Membranes

18 pages, 9413 KiB

Open AccessEditor’s ChoiceArticle

Performance and Enhanced Efficiency Induced by Cold Plasma on SAPO-34 Membranes for CO₂ and CH₄ Mixtures

by Fnu Gorky, Vashanti Storr, Grace Jones, Apolo Nambo, Jacek B. Jasinski and Maria L. Carreon

Membranes 2024, 14(8), 178; https://doi.org/10.3390/membranes14080178 - 20 Aug 2024

Viewed by 1885

In this study, we investigate the influence of cold-plasma-induced enhanced performance and efficiency of SAPO-34 membranes in the separation of CO₂ and CH₄ mixtures. Placing the herein presented research in a broader context, we aim to address the question of whether [...] Read more.

In this study, we investigate the influence of cold-plasma-induced enhanced performance and efficiency of SAPO-34 membranes in the separation of CO₂ and CH₄ mixtures. Placing the herein presented research in a broader context, we aim to address the question of whether cold plasma can significantly impact the membrane performance. We subjected SAPO-34 membranes to plasma mild disturbances and analyzed their performance in separating CO₂ and CH₄. Our findings reveal a notable enhancement in membrane efficiency and sustained performance when exposed to cold plasma. The pulsed plasma separation displayed improved structural integrity, and the experimental results indicated that the linear structure of CO₂ facilitates the distortion of electron clouds in response to the electric field, a property known as polarizability, which aids in effective separation. Plausible mechanistic insight indicated that the intermolecular forces facilitated an integral role in SAPO-34 membranes exhibiting strong electrostatic interactions. In conclusion, our research highlights the potential of cold plasma as a promising technique for improving the performance of SAPO-34 membranes in gas mixtures at atmospheric pressures, providing valuable insights for optimizing membrane technology in carbon capture and gas separation applications. Full article

(This article belongs to the Special Issue A Commemorative Special Issue in Honor of Dr. Moises Carreon)

► Show Figures

Figure 1

20 pages, 4099 KiB

Open AccessEditor’s ChoiceArticle

Treatment of Synthetic Wastewater Containing Polystyrene (PS) Nanoplastics by Membrane Bioreactor (MBR): Study of the Effects on Microbial Community and Membrane Fouling

by Anamary Pompa-Pernía, Serena Molina, Laura Cherta, Lorena Martínez-García and Junkal Landaburu-Aguirre

Membranes 2024, 14(8), 174; https://doi.org/10.3390/membranes14080174 - 9 Aug 2024

Viewed by 1173

Abstract

The persistent presence of micro- and nanoplastics (MNPs) in aquatic environments, particularly via effluents from wastewater treatment plants (WWTPs), poses significant ecological risks. This study investigated the removal efficiency of polystyrene nanoplastics (PS-NPs) using a lab-scale aerobic membrane bioreactor (aMBR) equipped with different [...] Read more.

The persistent presence of micro- and nanoplastics (MNPs) in aquatic environments, particularly via effluents from wastewater treatment plants (WWTPs), poses significant ecological risks. This study investigated the removal efficiency of polystyrene nanoplastics (PS-NPs) using a lab-scale aerobic membrane bioreactor (aMBR) equipped with different membrane types: microfiltration (MF), commercial ultrafiltration (c-UF), and recycled ultrafiltration (r-UF) membranes. Performance was assessed using synthetic urban wastewater spiked with PS-NPs, focusing on membrane efficiency, fouling behavior, and microbial community shifts. All aMBR systems achieved high organic matter removal, exceeding a 97% COD reduction in both the control and PS-exposed reactors. While low concentrations of PS-NPs did not significantly impact the sludge settleability or soluble microbial products initially, a higher accumulation increased the carbohydrate concentrations, indicating a protective bacterial response. The microbial community composition also adapted over time under polystyrene stress. All membrane types exhibited substantial NP removal; however, the presence of nano-sized PS particles negatively affected the membrane performance, enhancing the fouling phenomena and increasing transmembrane pressure. Despite this, the r-UF membrane demonstrated comparable efficiency to c-UF, suggesting its potential for sustainable applications. Advanced characterization techniques including pyrolysis gas chromatography/mass spectrometry (Py-GC/MS) were employed for NP detection and quantification. Full article

(This article belongs to the Special Issue Membrane Technologies for Water Purification)

► Show Figures

Figure 1

16 pages, 5680 KiB

Open AccessEditor’s ChoiceArticle

Mixed-Matrix Organo-Silica–Hydrotalcite Membrane for CO₂ Separation Part 1: Synthesis and Analytical Description

by Lucas Bünger, Krassimir Garbev, Angela Ullrich, Peter Stemmermann and Dieter Stapf

Membranes 2024, 14(8), 170; https://doi.org/10.3390/membranes14080170 - 6 Aug 2024

Viewed by 1312

Abstract

Hydrotalcite exhibits the capability to adsorb CO₂ at elevated temperatures. High surface area and favorable coating properties are essential to harness its potential for practical applications. Stable alcohol-based dispersions are needed for thin film applications of mixed membranes containing hydrotalcite. Currently, producing [...] Read more.

Hydrotalcite exhibits the capability to adsorb CO₂ at elevated temperatures. High surface area and favorable coating properties are essential to harness its potential for practical applications. Stable alcohol-based dispersions are needed for thin film applications of mixed membranes containing hydrotalcite. Currently, producing such dispersions without the need for delamination and dispersing agents is a challenging task. This work introduces, for the first time, a manufacturing approach to overcoming the drawbacks mentioned above. It includes a synthesis of hydrotalcite nanoparticles, followed by agent-free delamination of their layers and final dispersion into alcohol without dispersing agents. Further, the hydrotalcite-derived sorption agent is dispersed in a matrix based on organo-silica gels derived from 1,2-bis(triethoxysilyl)ethane (BTESE). The analytical results indicate that the interconnection between hydrotalcite and BTESE-derived gel occurs via forming a strong hydrogen bonding system between the interlayer species (OH groups, CO₃²⁻) of hydrotalcite and oxygen and silanol active gel centers. These findings lay the foundation for applications involving incorporating hydrotalcite-like compounds into silica matrices, ultimately enabling the development of materials with exceptional mass transfer properties. In part 2 of this study, the gas separation performance of the organo-silica and the hydrotalcite-like materials and their combined form will be investigated. Full article

(This article belongs to the Special Issue Advanced Membrane Materials for CO₂ Capture and Separation)

► Show Figures

Figure 1

23 pages, 18244 KiB

Open AccessEditor’s ChoiceArticle

Removal of Microplastics in a Hybrid Treatment Process of Ceramic Microfiltration and Photocatalyst-Mounted PES Spheres with Air Backwashing

by Minjoo Song and Jin Yong Park

Membranes 2024, 14(8), 169; https://doi.org/10.3390/membranes14080169 - 31 Jul 2024

Viewed by 1116

Abstract

Microplastics (MPs), which are defined as plastics with a size of less than 5 mm, cannot be treated completely in wastewater treatment plants (WWTPs) and discharged to a water body because they are too small in size. It has been reported that MPs [...] Read more.

Microplastics (MPs), which are defined as plastics with a size of less than 5 mm, cannot be treated completely in wastewater treatment plants (WWTPs) and discharged to a water body because they are too small in size. It has been reported that MPs can have adverse effects on human beings and water ecosystems. There is a need to combine existing drinking water treatment plants (DWTPs) and WWTPs with the traditional treatment process and technology with high removal efficiency of MPs or to develop a new technology to separate MPs from water and wastewater. In this study, the effects of MPs (polyethylene (PE), 125 μm) and organic matter (humic acid) were researched in a hybrid treatment process of ceramic microfiltration (MF) and photocatalyst (TiO₂)-mounted polyether sulfone (PES) spheres with air backwashing. The roles of the MF, photooxidation, and adsorption of PES spheres were confirmed in a single MF process (MF), an MF process with UV irradiation (MF+UV), MF and PES sphere adsorption without UV irradiation (MF+PES), and a hybrid process incorporating MF and PES spheres with UV irradiation (MF+PES+UV). The impact of the air backwashing cycle (filtration time, FT) on filtration characteristics and treatment efficiencies in the hybrid process was studied. In the MF process, membrane fouling increased with increasing organic matter (HA, humic acid). The treatment efficiency of MPs increased; however, that of dissolved organic matter (DOM) decreased with increasing HA. As MPs increased, the membrane fouling decreased; however, total filtration volume (V_T) remained almost constant. The treatment efficiency of MPs increased a little, and that of DOM showed a dropping trend. In the hybrid process, the membrane fouling was controlled via the adsorption and UV photooxidation of the PES spheres, and the DOM treatment efficiency increased by combining processes from MF to MF+PES+UV. The optimal FT was 10 min at BT 10 s in this hybrid process. The results could be applied to separate MPs effectively in DWTPs/WWTPs. Full article

(This article belongs to the Section Membrane Applications for Water Treatment)

► Show Figures

Figure 1

15 pages, 2271 KiB

Open AccessEditor’s ChoiceArticle

Lipid-Based Catalysis Demonstrated by Bilayer-Enabled Ester Hydrolysis

by Shu Liu, Kiran Kumar, Tracey Bell, Ayyalusamy Ramamoorthy, David Van Winkle and Steven Lenhert

Membranes 2024, 14(8), 168; https://doi.org/10.3390/membranes14080168 - 30 Jul 2024

Viewed by 1209

Abstract

Lipids have not traditionally been considered likely candidates for catalyzing reactions in biological systems. However, there is significant evidence that aggregates of amphiphilic compounds are capable of catalyzing reactions in synthetic organic chemistry. Here, we demonstrate the potential for the hydrophobic region of [...] Read more.

Lipids have not traditionally been considered likely candidates for catalyzing reactions in biological systems. However, there is significant evidence that aggregates of amphiphilic compounds are capable of catalyzing reactions in synthetic organic chemistry. Here, we demonstrate the potential for the hydrophobic region of a lipid bilayer to provide an environment suitable for catalysis by means of a lipid aggregate capable of speeding up a chemical reaction. By bringing organic molecules into the nonpolar or hydrophobic region of a lipid bilayer, reactions can be catalyzed by individual or collections of small, nonpolar, or amphiphilic molecules. We demonstrate this concept by the ester hydrolysis of calcein-AM to produce a fluorescent product, which is a widely used assay for esterase activity in cells. The reaction was first carried out in a two-phase octanol–water system, with the organic phase containing the cationic amphiphiles cetyltrimethylammonium bromide (CTAB) or octadecylamine. The octanol phase was then replaced with phospholipid vesicles in water, where the reaction was also found to be carried out. The reaction was monitored using quantitative fluorescence, which revealed catalytic turnover numbers on a scale of

10^{- 7}

to

10^{- 8}

s⁻¹ for each system, which is much slower than enzymatic catalysis. The reaction product was characterized by ¹H-NMR measurements, which were consistent with ester hydrolysis. The implications of thinking about lipids and lipid aggregates as catalytic entities are discussed in the context of biochemistry, pharmacology, and synthetic biology. Full article

(This article belongs to the Special Issue Structural, Dynamical, and Functional Implications of Membrane Compositional Heterogeneity)

► Show Figures

Figure 1

15 pages, 4602 KiB

Open AccessEditor’s ChoiceArticle

Influence of Feed Composition on the Separation Factor during Nanofiltration of Organic Acids

by Gustavo Tottoli, Sylvain Galier and Hélène Roux-de Balmann

Membranes 2024, 14(8), 166; https://doi.org/10.3390/membranes14080166 - 28 Jul 2024

Viewed by 1050

Abstract

In this study, nanofiltration experiments using synthetic solutions containing acetate, butyrate, and lactate are carried out to assess the impact of the feed composition, i.e., feed concentration and feed proportions, on the separation factor of couples of solutes in binary and ternary solutions. [...] Read more.

In this study, nanofiltration experiments using synthetic solutions containing acetate, butyrate, and lactate are carried out to assess the impact of the feed composition, i.e., feed concentration and feed proportions, on the separation factor of couples of solutes in binary and ternary solutions. In binary solutions, no influence of the solute proportions in the feed was pointed out, whatever the couple of solutes. The separation factor of acetate/butyrate and acetate/lactate was found to decrease with increasing feed concentration, while that of lactate/butyrate remained constant. The separation factors of acetate/lactate and lactate/butyrate were identical in ternary solutions compared to binary ones, showing no impact of the addition of the third solute. In ternary solutions, the presence of lactate decreased the separation factor of acetate/butyrate, but this decrease was not influenced by the proportion of lactate. Full article

(This article belongs to the Section Membrane Applications for Other Areas)

► Show Figures

Figure 1

30 pages, 3847 KiB

Open AccessEditor’s ChoiceReview

Carbon-Based Nanocomposite Membranes for Membrane Distillation: Progress, Problems and Future Prospects

by Chhabilal Regmi, Yuwaraj K. Kshetri and S. Ranil Wickramasinghe

Membranes 2024, 14(7), 160; https://doi.org/10.3390/membranes14070160 - 20 Jul 2024

Viewed by 1214

Abstract

The development of an ideal membrane for membrane distillation (MD) is of the utmost importance. Enhancing the efficiency of MD by adding nanoparticles to or onto a membrane’s surface has drawn considerable attention from the scientific community. It is crucial to thoroughly examine [...] Read more.

The development of an ideal membrane for membrane distillation (MD) is of the utmost importance. Enhancing the efficiency of MD by adding nanoparticles to or onto a membrane’s surface has drawn considerable attention from the scientific community. It is crucial to thoroughly examine state-of-the-art nanomaterials-enabled MD membranes with desirable properties, as they greatly enhance the efficiency and reliability of the MD process. This, in turn, opens up opportunities for achieving a sustainable water–energy–environment nexus. By introducing carbon-based nanomaterials into the membrane’s structure, the membrane gains excellent separation abilities, resistance to various feed waters, and a longer lifespan. Additionally, the use of carbon-based nanomaterials in MD has led to improved membrane performance characteristics such as increased permeability and a reduced fouling propensity. These nanomaterials have also enabled novel membrane capabilities like in situ foulant degradation and localized heat generation. Therefore, this review offers an overview of how the utilization of different carbon-based nanomaterials in membrane synthesis impacts the membrane characteristics, particularly the liquid entry pressure (LEP), hydrophobicity, porosity, and membrane permeability, as well as reduced fouling, thereby advancing the MD technology for water treatment processes. Furthermore, this review also discusses the development, challenges, and research opportunities that arise from these findings. Full article

(This article belongs to the Special Issue Membrane and Other Innovative Technologies for Water Purification: Design, Development, and Application)

► Show Figures

Figure 1

10 pages, 610 KiB

Open AccessEditor’s ChoiceReview

Electrophysiological Insights into Antibiotic Translocation and Resistance: The Impact of Outer Membrane Proteins

by Ishan Ghai

Membranes 2024, 14(7), 161; https://doi.org/10.3390/membranes14070161 - 20 Jul 2024

Viewed by 1221

Abstract

The alarming rise of antibiotic resistance in Gram-negative bacteria has emerged as a major global health challenge. A key factor contributing to this crisis is the low permeability of the bacterial outer membrane, which acts as a barrier that prevents antibiotics from entering [...] Read more.

The alarming rise of antibiotic resistance in Gram-negative bacteria has emerged as a major global health challenge. A key factor contributing to this crisis is the low permeability of the bacterial outer membrane, which acts as a barrier that prevents antibiotics from entering the cell. Protein channels embedded in this outer membrane selectively regulate the influx of hydrophilic compounds, including antibiotics. To combat antibiotic resistance, understanding the molecular mechanisms governing antibiotic permeability through bacterial membrane channels is crucial. This knowledge is key towards elucidating their roles in studing antibiotic resistance. By compiling and analysing the flux data from multiple electrophysiological reversal potential experimental studies, which involves measuring zero-current potentials and the corresponding single-channel conductance, we can calculate the flux of charged antibiotics/compounds across different Gram-negative bacterial outer membrane channels. Through this comprehensive synthesis, this review aims to advance our understanding and stimulate discussions about the physicochemical factors influencing the flux of antibiotics through bacterial membrane protein channels, ultimately enhancing our knowledge in this area. Full article

(This article belongs to the Section Biological Membrane Composition and Structures)

► Show Figures

Figure 1

33 pages, 7458 KiB

Open AccessEditor’s ChoiceArticle

Performance and Environmental Assessment of Biochar-Based Membranes Synthesized from Traditional and Eco-Friendly Solvents

by Abelline Fionah, Isaac Oluk, Laura Brady, Diana M. Byrne and Isabel C. Escobar

Membranes 2024, 14(7), 153; https://doi.org/10.3390/membranes14070153 - 11 Jul 2024

Viewed by 1510

Abstract

Water contamination resulting from coal spills is one of the largest environmental problems affecting communities in the Appalachia Region of the United States. This coal slurry contains potentially toxic substances, such as hydrocarbons, heavy metals, and coal cleaning chemicals, and its leakage into [...] Read more.

Water contamination resulting from coal spills is one of the largest environmental problems affecting communities in the Appalachia Region of the United States. This coal slurry contains potentially toxic substances, such as hydrocarbons, heavy metals, and coal cleaning chemicals, and its leakage into water bodies (lakes, rivers, and aquifers) can lead to adverse health effects not only for freshwater bodies and plant life but also for humans. This study focused on two major experiments. The first experiment involved the use of biochar to create a biochar–polysulfone (BC-PSf) flat-sheet multifunctional membrane to remove organic contaminants, and the other major experiment compared eco-friendly (gamma-valerolactone—GVL; Rhodiasolv^® PolarClean—PC) and petroleum-derived solvents (i.e., N-methyl-pyrrolidone—NMP) in the fabrication of the biochar–polysulfone membranes. The resulting membranes were tested for their efficiency in removing both positively and negatively charged organic contaminants from the collected water at varying pH values. A comparative life cycle assessment (LCA) with accompanying uncertainty and sensitivity analyses was carried out to understand the global environmental impacts of incorporating biochar, NMP, GVL, and PC in the synthesis of PSf/NMP, BC-PSf/NMP, PSf/GVL, BC-PSf/GVL, PSf/PC, and BC-PSf/PC membranes at a set surface area of 1000 m². The results showed that the addition of biochar to the membrane matrix increased the surface area of the membranes and improved both their adsorptive and mechanical properties. The membranes with biochar incorporated in their matrix showed a higher potential for contaminant removal than those without biochar. The environmental impacts normalized to the BC-PSf/GVL membrane showed that the addition of biochar increased global warming impacts, eutrophication, and respiratory impacts by over 100% in all the membrane configurations with biochar. The environmental impacts were highly sensitive to biochar addition (Spearman’s coefficient > 0.8). The BC/PSf membrane with Rhodiasolv^® PolarClean had the lowest associated global environmental impacts among all the membranes with biochar. Ultimately, this study highlighted potential tradeoffs between functional performance and global environmental impacts regarding choices for membrane fabrication. Full article

(This article belongs to the Collection Polymeric Membranes: Science, Materials and Applications)

► Show Figures

Figure 1

13 pages, 7170 KiB

Open AccessEditor’s ChoiceArticle

Application of Recycled Ultrafiltration Membranes in an Aerobic Membrane Bioreactor (aMBR): A Validation Study

by Laura Rodríguez-Sáez, Junkal Landaburu-Aguirre, Eloy García-Calvo and Serena Molina

Membranes 2024, 14(7), 149; https://doi.org/10.3390/membranes14070149 - 5 Jul 2024

Viewed by 1084

Abstract

A validation study using recycled ultrafiltration membranes (r-UF) on an aerobic membrane bioreactor (aMBR) was conducted for the first time. Four different polyethersulfone (PES) membranes were tested using synthetic urban wastewater (COD 0.4–0.5 g/L) during two experimental periods: (i) recycled ultrafiltration membrane (r-UF) [...] Read more.

A validation study using recycled ultrafiltration membranes (r-UF) on an aerobic membrane bioreactor (aMBR) was conducted for the first time. Four different polyethersulfone (PES) membranes were tested using synthetic urban wastewater (COD 0.4–0.5 g/L) during two experimental periods: (i) recycled ultrafiltration membrane (r-UF) and commercial UF membrane (molecular weight cut-off (MWCO) 150 kDa) (c-150 kDa); (ii) r-UF membrane modified by dip-coating using catechol (CA) and polyethyleneimine (PEI) (mr-UF) and c-20 kDa membrane. Permeability, fouling behavior, and permeate quality were evaluated. Extensive membrane characterization was conducted using scanning electron microscopy (SEM), atomic force microscopy (AFM), energy-dispersive X-ray (EDX), and confocal laser scanning microscopy (CLSM). Permeate quality for r-UF and mr-UF membranes was excellent and comparable to that obtained using commercial membranes under similar conditions. Additionally, r-UF and mr-UF membranes presented a steadier performance time. Additionally, r-UF membrane demonstrated less tendency to be fouled (R_f, m⁻¹) r-UF 7.92 ± 0.57 × 10¹²; mr-UF 9.90 ± 0.14 × 10¹², c-150 kDa 1.56 ± 0.07 × 10¹³ and c-20 kDa 1.25 ± 0.50 × 10¹³. The r-UF membrane showed an excellent antibiofouling character. Therefore, r-UF membranes can be successfully implemented for wastewater treatment in aMBR, being a sustainable and cost-effective alternative to commercial membranes that can contribute to overcome membrane fouling and membrane replacement issues. Full article

(This article belongs to the Special Issue Advanced Membranes and Membrane Technologies for Wastewater Treatment)

► Show Figures

Figure 1

15 pages, 2161 KiB

Open AccessEditor’s ChoiceArticle

Efficient Isolation of Outer Membrane Vesicles (OMVs) Secreted by Gram-Negative Bacteria via a Novel Gradient Filtration Method

by Ning Li, Minghui Wu, Lu Wang, Mengyu Tang, Hongbo Xin and Keyu Deng

Membranes 2024, 14(6), 135; https://doi.org/10.3390/membranes14060135 - 6 Jun 2024

Cited by 1 | Viewed by 1940

Abstract

Bacterial extracellular vesicles (bEVs) secreted by Gram-negative bacteria are referred to as outer membrane vesicles (OMVs) because they originate in the outer membrane. OMVs are membrane-coated vesicles 20–250 nm in size. They contain lipopolysaccharide (LPS), peptidoglycan, proteins, lipids, nucleic acids, and other substances [...] Read more.

Bacterial extracellular vesicles (bEVs) secreted by Gram-negative bacteria are referred to as outer membrane vesicles (OMVs) because they originate in the outer membrane. OMVs are membrane-coated vesicles 20–250 nm in size. They contain lipopolysaccharide (LPS), peptidoglycan, proteins, lipids, nucleic acids, and other substances derived from their parent bacteria and participate in the transmission of information to host cells. OMVs have broad prospects in terms of potential application in the fields of adjuvants, vaccines, and drug delivery vehicles. Currently, there remains a lack of efficient and convenient methods to isolate OMVs, which greatly limits OMV-related research. In this study, we developed a fast, convenient, and low-cost gradient filtration method to separate OMVs that can achieve industrial-scale production while maintaining the biological activity of the isolated OMVs. We compared the gradient filtration method with traditional ultracentrifugation to isolate OMVs from probiotic Escherichia coli Nissle 1917 (EcN) bacteria. Then, we used RAW264.7 macrophages as an in vitro model to study the influence on the immune function of EcN-derived OMVs obtained through the gradient filtration method. Our results indicated that EcN-derived OMVs were efficiently isolated using our gradient filtration method. The level of OMV enrichment obtained via our gradient filtration method was about twice as efficient as that achieved through traditional ultracentrifugation. The EcN-derived OMVs enriched through the gradient filtration method were successfully taken up by RAW264.7 macrophages and induced them to secrete pro-inflammatory cytokines such as tumor necrosis factor α (TNF-α) and interleukins (ILs) 6 and 1β, as well as anti-inflammatory cytokine IL-10. Furthermore, EcN-derived OMVs induced more anti-inflammatory response (i.e., IL-10) than pro-inflammatory response (i.e., TNF-α, IL-6, and IL-1β). These results were consistent with those reported in the literature. The related literature reported that EcN-derived OMVs obtained through ultracentrifugation could induce stronger anti-inflammatory responses than pro-inflammatory responses in RAW264.7 macrophages. Our simple and novel separation method may therefore have promising prospects in terms of applications involving the study of OMVs. Full article

(This article belongs to the Special Issue Design and Characterization of Membranes for Biomedical Applications)

► Show Figures

Figure 1

18 pages, 3171 KiB

Open AccessEditor’s ChoiceReview

A Short Review of Advances in MOF Glass Membranes for Gas Adsorption and Separation

by Zichen Li, Yumei Wang, Jianxin Zhang, Shiqi Cheng and Yue Sun

Membranes 2024, 14(5), 99; https://doi.org/10.3390/membranes14050099 - 25 Apr 2024

Cited by 1 | Viewed by 2727

Abstract

The phenomenon of melting in metal–organic frameworks (MOFs) has recently garnered attention. Crystalline MOF materials can be transformed into an amorphous glassy state through melt-quenching treatment. The resulting MOF glass structure eliminates grain boundaries and retains short-range order while exhibiting long-range disorder. Based [...] Read more.

The phenomenon of melting in metal–organic frameworks (MOFs) has recently garnered attention. Crystalline MOF materials can be transformed into an amorphous glassy state through melt-quenching treatment. The resulting MOF glass structure eliminates grain boundaries and retains short-range order while exhibiting long-range disorder. Based on these properties, it emerges as a promising candidate for high-performance separation membranes. MOF glass membranes exhibit permanent and accessible porosity, allowing for selective adsorption of different gas species. This review summarizes the melting mechanism of MOFs and explores the impact of ligands and metal ions on glassy MOFs. Additionally, it presents an analysis of the diverse classes of MOF glass composites, outlining their structures and properties, which are conducive to gas adsorption and separation. The absence of inter-crystalline defects in the structures, coupled with their distinctive mechanical properties, renders them highly promising for industrial gas separation applications. Furthermore, this review provides a summary of recent research on MOF glass composite membranes for gas adsorption and separation. It also addresses the challenges associated with membrane production and suggests future research directions. Full article

(This article belongs to the Special Issue Recent Advances of Metal–Organic Framework Membranes for Separation Process)

► Show Figures

Figure 1

24 pages, 2757 KiB

Open AccessEditor’s ChoiceReview

Recent Advances and Challenges in Anion Exchange Membranes Development/Application for Water Electrolysis: A Review

by Lu Liu, Hongyang Ma, Madani Khan and Benjamin S. Hsiao

Membranes 2024, 14(4), 85; https://doi.org/10.3390/membranes14040085 - 5 Apr 2024

Cited by 5 | Viewed by 5212

Abstract

In recent years, anion exchange membranes (AEMs) have aroused widespread interest in hydrogen production via water electrolysis using renewable energy sources. The two current commercial low-temperature water electrolysis technologies used are alkaline water electrolysis (AWE) and proton exchange membrane (PEM) water electrolysis. The [...] Read more.

In recent years, anion exchange membranes (AEMs) have aroused widespread interest in hydrogen production via water electrolysis using renewable energy sources. The two current commercial low-temperature water electrolysis technologies used are alkaline water electrolysis (AWE) and proton exchange membrane (PEM) water electrolysis. The AWE technology exhibited the advantages of high stability and increased cost-effectiveness with low hydrogen production efficiency. In contrast, PEM water electrolysis exhibited high hydrogen efficiency with low stability and cost-effectiveness, respectively. Unfortunately, the major challenges that AEMs, as well as the corresponding ion transportation membranes, including alkaline hydrogen separator and proton exchange membranes, still face are hydrogen production efficiency, long-term stability, and cost-effectiveness under working conditions, which exhibited critical issues that need to be addressed as a top priority. This review comprehensively presented research progress on AEMs in recent years, providing a thorough understanding of academic studies and industrial applications. It focused on analyzing the chemical structure of polymers and the performance of AEMs and established the relationship between the structure and efficiency of the membranes. This review aimed to identify approaches for improving AEM ion conductivity and alkaline stability. Additionally, future research directions for the commercialization of anion exchange membranes were discussed based on the analysis and assessment of the current applications of AEMs in patents. Full article

(This article belongs to the Collection Feature Papers in Membrane Processing and Engineering)

► Show Figures

Graphical abstract

17 pages, 2949 KiB

Open AccessEditor’s ChoiceArticle

Hydrophilic Modification of Dialysis Membranes Sustains Middle Molecule Removal and Filtration Characteristics

by Adam M. Zawada, Karlee Emal, Eva Förster, Saeedeh Saremi, Dirk Delinski, Lukas Theis, Florian Küng, Wenhao Xie, Joanie Werner, Manuela Stauss-Grabo, Matthias Faust, Skyler Boyington and James P. Kennedy

Membranes 2024, 14(4), 83; https://doi.org/10.3390/membranes14040083 - 3 Apr 2024

Cited by 1 | Viewed by 2432

Abstract

While efficient removal of uremic toxins and accumulated water is pivotal for the well-being of dialysis patients, protein adsorption to the dialyzer membrane reduces the performance of a dialyzer. Hydrophilic membrane modification with polyvinylpyrrolidone (PVP) has been shown to reduce protein adsorption and [...] Read more.

While efficient removal of uremic toxins and accumulated water is pivotal for the well-being of dialysis patients, protein adsorption to the dialyzer membrane reduces the performance of a dialyzer. Hydrophilic membrane modification with polyvinylpyrrolidone (PVP) has been shown to reduce protein adsorption and to stabilize membrane permeability. In this study we compared middle molecule clearance and filtration performance of nine polysulfone-, polyethersulfone-, and cellulose-based dialyzers over time. Protein adsorption was simulated in recirculation experiments, while β2-microglobulin clearance as well as transmembrane pressure (TMP) and filtrate flow were determined over time. The results of this study showed that β2-microglobulin clearance (−7.2 mL/min/m²) and filtrate flow (−54.4 mL/min) decreased strongly during the first 30 min and slowly afterwards (−0.7 mL/min/m² and −6.8 mL/min, respectively, for the next 30 min); the TMP increase (+37.2 mmHg and +8.6 mmHg, respectively) showed comparable kinetics. Across all tested dialyzers, the dialyzer with a hydrophilic modified membrane (FX CorAL) had the highest β2-microglobulin clearance after protein fouling and the most stable filtration characteristics. In conclusion, hydrophilic membrane modification with PVP stabilizes the removal capacity of middle molecules and filtration performance over time. Such dialyzers may have benefits during hemodiafiltration treatments which aim to achieve high exchange volumes. Full article

(This article belongs to the Topic Nephrology and Dialysis: From Bench to Bedside)

► Show Figures

Figure 1

20 pages, 5158 KiB

Open AccessEditor’s ChoiceArticle

Experimental Investigation on the Energy and Exergy Efficiency of the Vacuum Membrane Distillation System with Its Various Configurations

by Abdullah Najib, Turki Mana, Emad Ali, Hany Al-Ansary, Fahad Awjah Almehmadi and Mansour Alhoshan

Membranes 2024, 14(2), 54; https://doi.org/10.3390/membranes14020054 - 13 Feb 2024

Cited by 1 | Viewed by 1694

Abstract

This paper addresses a retrofitting vacuum membrane distillation (VMD) setup to reduce the accumulated pressure inside the permeated side. This modification is necessary to extend the operation of the VMD to extreme operation conditions of higher hot water temperatures. This modification, denoted as [...] Read more.

This paper addresses a retrofitting vacuum membrane distillation (VMD) setup to reduce the accumulated pressure inside the permeated side. This modification is necessary to extend the operation of the VMD to extreme operation conditions of higher hot water temperatures. This modification, denoted as a hybrid configuration, proposes the injection of a cold water stream into the VMD cell without mixing it with the permeate. Energy and exergy efficiency analyses were performed to assess the effectiveness of the hybrid configuration. The performance of the modified system indicated an improvement in terms of permeate flux (J), the gain output ratio (GOR), and the utilitarian exergetic efficiency (η_ex,u), which reach up to two and three times that of the base configuration of the VMD system. However, the exergetic efficiency (η_ex) of the hybrid system showed marginal improvement compared to the base case over the tested range of hot water temperatures. This is because the enhanced vapor production is penalized by excess energy consumption. Moreover, the highest exergy destruction percentages occurred in the operational components (e.g., heater and chillers) which fall in the range of 19.0–68.9%. The exergy destruction percentage in the original components (e.g., the VMD cell and condenser) did not exceed 8.3%. Furthermore, this study indicated that the hybrid configuration requires additional tuning and optimization to perform efficiently over wide operating conditions. Full article

(This article belongs to the Special Issue Applications of Membrane Processes in Desalination, Wastewater Treatment and Resource Recovery)

► Show Figures

Figure 1

27 pages, 7988 KiB

Open AccessEditor’s ChoiceReview

Sustainability in Membrane Technology: Membrane Recycling and Fabrication Using Recycled Waste

by Noman Khalid Khanzada, Raed A. Al-Juboori, Muzamil Khatri, Farah Ejaz Ahmed, Yazan Ibrahim and Nidal Hilal

Membranes 2024, 14(2), 52; https://doi.org/10.3390/membranes14020052 - 12 Feb 2024

Cited by 7 | Viewed by 5536

Abstract

Membrane technology has shown a promising role in combating water scarcity, a globally faced challenge. However, the disposal of end-of-life membrane modules is problematic as the current practices include incineration and landfills as their final fate. In addition, the increase in population and [...] Read more.

Membrane technology has shown a promising role in combating water scarcity, a globally faced challenge. However, the disposal of end-of-life membrane modules is problematic as the current practices include incineration and landfills as their final fate. In addition, the increase in population and lifestyle advancement have significantly enhanced waste generation, thus overwhelming landfills and exacerbating environmental repercussions and resource scarcity. These practices are neither economically nor environmentally sustainable. Recycling membranes and utilizing recycled material for their manufacturing is seen as a potential approach to address the aforementioned challenges. Depending on physiochemical conditions, the end-of-life membrane could be reutilized for similar, upgraded, and downgraded operations, thus extending the membrane lifespan while mitigating the environmental impact that occurred due to their disposal and new membrane preparation for similar purposes. Likewise, using recycled waste such as polystyrene, polyethylene terephthalate, polyvinyl chloride, tire rubber, keratin, and cellulose and their derivates for fabricating the membranes can significantly enhance environmental sustainability. This study advocates for and supports the integration of sustainability concepts into membrane technology by presenting the research carried out in this area and rigorously assessing the achieved progress. The membranes’ recycling and their fabrication utilizing recycled waste materials are of special interest in this work. Furthermore, this study offers guidance for future research endeavors aimed at promoting environmental sustainability. Full article

(This article belongs to the Special Issue Sustainable Polymeric Membrane Preparation and Application)

► Show Figures

Figure 1

21 pages, 5677 KiB

Open AccessEditor’s ChoiceArticle

Field-Scale Testing of a High-Efficiency Membrane Reactor (MR)—Adsorptive Reactor (AR) Process for H₂ Generation and Pre-Combustion CO₂ Capture

by Nicholas Margull, Doug Parsley, Ibubeleye Somiari, Linghao Zhao, Mingyuan Cao, Dimitrios Koumoulis, Paul K. T. Liu, Vasilios I. Manousiouthakis and Theodore T. Tsotsis

Membranes 2024, 14(2), 51; https://doi.org/10.3390/membranes14020051 - 11 Feb 2024

Cited by 2 | Viewed by 2097

Abstract

The study objective was to field-validate the technical feasibility of a membrane- and adsorption-enhanced water gas shift reaction process employing a carbon molecular sieve membrane (CMSM)-based membrane reactor (MR) followed by an adsorptive reactor (AR) for pre-combustion CO₂ capture. The project was [...] Read more.

The study objective was to field-validate the technical feasibility of a membrane- and adsorption-enhanced water gas shift reaction process employing a carbon molecular sieve membrane (CMSM)-based membrane reactor (MR) followed by an adsorptive reactor (AR) for pre-combustion CO₂ capture. The project was carried out in two different phases. In Phase I, the field-scale experimental MR-AR system was designed and constructed, the membranes, and adsorbents were prepared, and the unit was tested with simulated syngas to validate functionality. In Phase II, the unit was installed at the test site, field-tested using real syngas, and a technoeconomic analysis (TEA) of the technology was completed. All project milestones were met. Specifically, (i) high-performance CMSMs were prepared meeting the target H₂ permeance (>1 m³/(m².hbar) and H₂/CO selectivity of >80 at temperatures of up to 300 °C and pressures of up to 25 bar with a <10% performance decline over the testing period; (ii) pelletized adsorbents were prepared for use in relevant conditions (250 °C < T < 450 °C, pressures up to 25 bar) with a working capacity of >2.5 wt.% and an attrition rate of <0.2; (iii) TEA showed that the MR-AR technology met the CO₂ capture goals of 95% CO₂ purity at a cost of electricity (COE) 30% less than baseline approaches. Full article

(This article belongs to the Special Issue Sorption and Transport Phenomena in Inorganic Membranes)

► Show Figures

Figure 1

17 pages, 13402 KiB

Open AccessEditor’s ChoiceReview

Roles of a Glycolipid MPIase in Sec-Independent Membrane Protein Insertion

by Kaoru Nomura, Shoko Mori and Keiko Shimamoto

Membranes 2024, 14(2), 48; https://doi.org/10.3390/membranes14020048 - 8 Feb 2024

Cited by 1 | Viewed by 1792

Abstract

Membrane protein integrase (MPIase), an endogenous glycolipid in Escherichia coli (E. coli) membranes, is essential for membrane protein insertion in E. coli. We have examined Sec-independent membrane protein insertion mechanisms facilitated by MPIase using physicochemical analytical techniques, namely solid-state nuclear [...] Read more.

Membrane protein integrase (MPIase), an endogenous glycolipid in Escherichia coli (E. coli) membranes, is essential for membrane protein insertion in E. coli. We have examined Sec-independent membrane protein insertion mechanisms facilitated by MPIase using physicochemical analytical techniques, namely solid-state nuclear magnetic resonance, fluorescence measurements, and surface plasmon resonance. In this review, we outline the physicochemical characteristics of membranes that may affect membrane insertion of proteins. Subsequently, we introduce our results verifying the effects of membrane lipids on insertion and estimate the impact of MPIase. Although MPIase is a minor component of E. coli membranes, it regulates insertion by altering the physicochemical properties of the membrane. In addition, MPIase promotes insertion by interacting with substrate proteins. We propose comprehensive mechanisms for the membrane insertion of proteins involving MPIase, which provide a physicochemical basis for understanding the roles of glycolipids in protein translocation. Full article

(This article belongs to the Special Issue Advanced Research on Structure-Function Relationships of Membrane Proteins, 2nd Edition)

► Show Figures

Figure 1

17 pages, 7218 KiB

Open AccessEditor’s ChoiceArticle

Identification of Membrane Fouling with Greywater Filtration by Porous Membranes: Combined Effect of Membrane Pore Size and Applied Pressure

by Hoseok Jang, Sinu Kang and Jeonghwan Kim

Membranes 2024, 14(2), 46; https://doi.org/10.3390/membranes14020046 - 7 Feb 2024

Cited by 2 | Viewed by 2019

Abstract

Membrane fouling caused by complex greywater synthesized by personal care products and detergents commercially available for household applications was investigated using dead-end microfiltration (MF) and analyzed systematically by a multistage Hermia blocking model as a first attempt. The highest flux decline was associated [...] Read more.

Membrane fouling caused by complex greywater synthesized by personal care products and detergents commercially available for household applications was investigated using dead-end microfiltration (MF) and analyzed systematically by a multistage Hermia blocking model as a first attempt. The highest flux decline was associated with the smallest pore size of the membrane (0.03 μm). This effectiveness was more pronounced at higher applied pressures to the membrane. A cake layer was formed on the membrane consisting mainly of silica particles present as ingredients in greywater. Although organic rejection was low by the porous MF membrane, the organic compound contributed to membrane fouling in the filtration stage. With a 0.03 μm pore size of the membrane, dominant fouling mechanisms were classified into three stages as applied pressure increased, such as complete pore blocking, intermediate pore blocking, and cake layer formation. Specifically, during the early stage of membrane filtration at 1.5 bar, membrane fouling was determined by complete pore blocking in the 0.10 μm pore size of the membrane. However, the later stage of membrane fouling was controlled mainly by intermediate pore blocking. Regardless of the applied pressure, pore constriction or standard blocking played an important role in the fouling rate with a 0.45 μm pore size of the membrane. Our results also support that complex formation can occur due to the concentration of organic and inorganic species present in simulated greywater. Thus, strategic approaches such as periodic, chemically enhanced backwashing need to be developed and tailored to remove both organic and inorganic fouling from MF membranes treating greywater. Full article

(This article belongs to the Special Issue Advanced Membrane Bioreactors for Wastewater Treatment 2nd Edition)

► Show Figures

Figure 1

23 pages, 9180 KiB

Open AccessEditor’s ChoiceArticle

Studying Conformational Properties of Transmembrane Domain of KCNE3 in a Lipid Bilayer Membrane Using Molecular Dynamics Simulations

by Anna Clara Miranda Moura, Isaac K. Asare, Mateo Fernandez Cruz, Antonio Javier Franco Aguado, Kaeleigh Dyan Tuck, Conner C. Campbell, Matthew W. Scheyer, Ikponwmosa Obaseki, Steve Alston, Andrea N. Kravats, Charles R. Sanders, Gary A. Lorigan and Indra D. Sahu

Membranes 2024, 14(2), 45; https://doi.org/10.3390/membranes14020045 - 4 Feb 2024

Cited by 1 | Viewed by 2179

Abstract

KCNE3 is a single-pass integral membrane protein that regulates numerous voltage-gated potassium channel functions such as KCNQ1. Previous solution NMR studies suggested a moderate degree of curved α-helical structure in the transmembrane domain (TMD) of KCNE3 in lyso-myristoylphosphatidylcholine (LMPC) micelles and isotropic bicelles [...] Read more.

KCNE3 is a single-pass integral membrane protein that regulates numerous voltage-gated potassium channel functions such as KCNQ1. Previous solution NMR studies suggested a moderate degree of curved α-helical structure in the transmembrane domain (TMD) of KCNE3 in lyso-myristoylphosphatidylcholine (LMPC) micelles and isotropic bicelles with the residues T71, S74 and G78 situated along the concave face of the curved helix. During the interaction of KCNE3 and KCNQ1, KCNE3 pushes its transmembrane domain against KCNQ1 to lock the voltage sensor in its depolarized conformation. A cryo-EM study of KCNE3 complexed with KCNQ1 in nanodiscs suggested a deviation of the KCNE3 structure from its independent structure in isotropic bicelles. Despite the biological significance of KCNE3 TMD, the conformational properties of KCNE3 are poorly understood. Here, all atom molecular dynamics (MD) simulations were utilized to investigate the conformational dynamics of the transmembrane domain of KCNE3 in a lipid bilayer containing a mixture of POPC and POPG lipids (3:1). Further, the effect of the interaction impairing mutations (V72A, I76A and F68A) on the conformational properties of the KCNE3 TMD in lipid bilayers was investigated. Our MD simulation results suggest that the KCNE3 TMD adopts a nearly linear α helical structural conformation in POPC-POPG lipid bilayers. Additionally, the results showed no significant change in the nearly linear α-helical conformation of KCNE3 TMD in the presence of interaction impairing mutations within the sampled time frame. The KCNE3 TMD is more stable with lower flexibility in comparison to the N-terminal and C-terminal of KCNE3 in lipid bilayers. The overall conformational flexibility of KCNE3 also varies in the presence of the interaction-impairing mutations. The MD simulation data further suggest that the membrane bilayer width is similar for wild-type KCNE3 and KCNE3 containing mutations. The Z-distance measurement data revealed that the TMD residue site A69 is close to the lipid bilayer center, and residue sites S57 and S82 are close to the surfaces of the lipid bilayer membrane for wild-type KCNE3 and KCNE3 containing interaction-impairing mutations. These results agree with earlier KCNE3 biophysical studies. The results of these MD simulations will provide complementary data to the experimental outcomes of KCNE3 to help understand its conformational dynamic properties in a more native lipid bilayer environment. Full article

(This article belongs to the Special Issue Analytical Sciences of/with Bio(mimetic) Membranes (Volume II))

► Show Figures

Figure 1

15 pages, 2348 KiB

Open AccessEditor’s ChoiceArticle

Impact of Concentration Polarization Phenomena on Gas Separation Processes with High-Performance Zeolite Membranes: Experiments vs. Simulations

by Omar Abdul Majid, Margarita Kuznetsova, Christophe Castel, Eric Favre and Rainier Hreiz

Membranes 2024, 14(2), 41; https://doi.org/10.3390/membranes14020041 - 1 Feb 2024

Cited by 2 | Viewed by 2376

Abstract

Polarization phenomena play a key role in membrane separation processes but remain largely unexplored for gas separations, where the mass transfer resistance is most often limited to the membrane. This assumption, which is commonly used today for the simulation of membrane gas separations, [...] Read more.

Polarization phenomena play a key role in membrane separation processes but remain largely unexplored for gas separations, where the mass transfer resistance is most often limited to the membrane. This assumption, which is commonly used today for the simulation of membrane gas separations, has to be reconsidered when high-performance materials, showing a very high permeance and/or selectivity, are used. In this study, a series of steady-state separation performances experimentally obtained on CO₂/CH₄ mixtures with a zeolite membrane are compared to the predictions of a dedicated 1D approach, recently derived and validated through CFD simulations. Polarization effects are shown to generate a significant negative impact on the separation performances, both in terms of the productivity and separation efficiency. The 1D model predictions, based on pure gas permeance data and without any adjustable parameters, are in very good agreement with the experimental data. This fast and efficient modeling approach can easily be implemented in simulation or process synthesis programs for the rigorous evaluation of membrane gas separation processes, when high-performance materials are used. Full article

(This article belongs to the Section Membrane Processing and Engineering)

► Show Figures

Figure 1

22 pages, 1495 KiB

Open AccessEditor’s ChoiceReview

Water, Protons, and the Gating of Voltage-Gated Potassium Channels

by Alisher M. Kariev and Michael E. Green

Membranes 2024, 14(2), 37; https://doi.org/10.3390/membranes14020037 - 29 Jan 2024

Cited by 1 | Viewed by 2461

Abstract

Ion channels are ubiquitous throughout all forms of life. Potassium channels are even found in viruses. Every cell must communicate with its surroundings, so all cells have them, and excitable cells, in particular, especially nerve cells, depend on the behavior of these channels. [...] Read more.

Ion channels are ubiquitous throughout all forms of life. Potassium channels are even found in viruses. Every cell must communicate with its surroundings, so all cells have them, and excitable cells, in particular, especially nerve cells, depend on the behavior of these channels. Every channel must be open at the appropriate time, and only then, so that each channel opens in response to the stimulus that tells that channel to open. One set of channels, including those in nerve cells, responds to voltage. There is a standard model for the gating of these channels that has a section of the protein moving in response to the voltage. However, there is evidence that protons are moving, rather than protein. Water is critical as part of the gating process, although it is hard to see how this works in the standard model. Here, we review the extensive evidence of the importance of the role of water and protons in gating these channels. Our principal example, but by no means the only example, will be the K_v1.2 channel. Evidence comes from the effects of D₂O, from mutations in the voltage sensing domain, as well as in the linker between that domain and the gate, and at the gate itself. There is additional evidence from computations, especially quantum calculations. Structural evidence comes from X-ray studies. The hydration of ions is critical in the transfer of ions in constricted spaces, such as the gate region and the pore of a channel; we will see how the structure of the hydrated ion fits with the structure of the channel. In addition, there is macroscopic evidence from osmotic experiments and streaming current measurements. The combined evidence is discussed in the context of a model that emphasizes the role of protons and water in gating these channels. Full article

(This article belongs to the Special Issue Function and Malfunction of Ion Channels in Biological Cell Membrane)

► Show Figures

Figure 1

12 pages, 1393 KiB

Open AccessEditor’s ChoiceArticle

Ultra-Stable Inorganic Mesoporous Membranes for Water Purification

by Ralph A. Bauer, Minghui Qiu, Melissa C. Schillo-Armstrong, Matthew T. Snider, Zi Yang, Yi Zhou and Hendrik Verweij

Membranes 2024, 14(2), 34; https://doi.org/10.3390/membranes14020034 - 27 Jan 2024

Cited by 1 | Viewed by 2058

Abstract

Thin, supported inorganic mesoporous membranes are used for the removal of salts, small molecules (PFAS, dyes, and polyanions) and particulate species (oil droplets) from aqueous sources with high flux and selectivity. Nanofiltration membranes can reject simple salts with 80–100% selectivity through a space [...] Read more.

Thin, supported inorganic mesoporous membranes are used for the removal of salts, small molecules (PFAS, dyes, and polyanions) and particulate species (oil droplets) from aqueous sources with high flux and selectivity. Nanofiltration membranes can reject simple salts with 80–100% selectivity through a space charge mechanism. Rejection by size selectivity can be near 100% since the membranes can have a very narrow size distribution. Mesoporous membranes have received particular interest due to their (potential) stability under operational conditions and during defouling operations. More recently, membranes with extreme stability became interesting with the advent of in situ fouling mitigation by means of ultrasound emitted from within the membrane structure. For this reason, we explored the stability of available and new membranes with accelerated lifetime tests in aqueous solutions at various temperatures and pH values. Of the available ceria, titania, and magnetite membranes, none were actually stable under all test conditions. In earlier work, it was established that mesoporous alumina membranes have very poor stability. A new nanofiltration membrane was made of cubic zirconia membranes that exhibited near-perfect stability. A new ultrafiltration membrane was made of amorphous silica that was fully stable in ultrapure water at 80 °C. This work provides details of membrane synthesis, stability characterization and data and their interpretation. Full article

(This article belongs to the Special Issue Latest Research on Pollutants Removal from Aqueous Media by Membrane Processes)

► Show Figures

Figure 1

14 pages, 4224 KiB

Open AccessEditor’s ChoiceArticle

Facilitating Water Permeation in Graphene Oxide Membranes via Incorporating Sulfonato Calix[n]arenes

by Yufan Ji, Shurui Dong, Yiping Huang, Changhai Yue, Hao Zhu, Dan Wu and Jing Zhao

Membranes 2024, 14(2), 32; https://doi.org/10.3390/membranes14020032 - 24 Jan 2024

Cited by 1 | Viewed by 1761

Abstract

Graphene oxide (GO) with its atomic thickness and abundant functional groups holds great potential in molecular-scale membrane separation. However, constructing high-speed and highly selective water transport channels within GO membranes remains a key challenge. Herein, sulfonato calix[n]arenes (SCn) molecules with a cavity structure, [...] Read more.

Graphene oxide (GO) with its atomic thickness and abundant functional groups holds great potential in molecular-scale membrane separation. However, constructing high-speed and highly selective water transport channels within GO membranes remains a key challenge. Herein, sulfonato calix[n]arenes (SCn) molecules with a cavity structure, hydrophilic entrance, and hydrophobic wall were incorporated into GO interlayer channels through a layer-by-layer assembly approach to facilitate water permeation in a water/ethanol separation process. The hydrophilic entrance enables preferential access of water molecules to the cavity over ethanol molecules, while the high hydrophobicity of the cavity wall confers low resistance for water diffusion. After incorporating SCn molecules, the membrane shows a remarkable increase in the water/ethanol separation factor from 732 to 1260, while the permeate flux also increases by about 50%. In addition, the strong electrostatic interactions between the building blocks endow the membrane with excellent swelling resistance even under a high water content. This work provides an effective strategy of constructing high-efficiency water transport channels in membrane. Full article

(This article belongs to the Special Issue Graphene Oxide Membrane for Sustainable Energy and Environmental Applications)

► Show Figures

Graphical abstract

25 pages, 3235 KiB

Open AccessEditor’s ChoiceReview

Membrane Separation Technology in Direct Air Capture

by Pavlo Ignatusha, Haiqing Lin, Noe Kapuscinsky, Ludmila Scoles, Weiguo Ma, Bussaraporn Patarachao and Naiying Du

Membranes 2024, 14(2), 30; https://doi.org/10.3390/membranes14020030 - 24 Jan 2024

Cited by 6 | Viewed by 4967

Abstract

Direct air capture (DAC) is an emerging negative CO₂ emission technology that aims to introduce a feasible method for CO₂ capture from the atmosphere. Unlike carbon capture from point sources, which deals with flue gas at high CO₂ concentrations, carbon [...] Read more.

Direct air capture (DAC) is an emerging negative CO₂ emission technology that aims to introduce a feasible method for CO₂ capture from the atmosphere. Unlike carbon capture from point sources, which deals with flue gas at high CO₂ concentrations, carbon capture directly from the atmosphere has proved difficult due to the low CO₂ concentration in ambient air. Current DAC technologies mainly consider sorbent-based systems; however, membrane technology can be considered a promising DAC approach since it provides several advantages, e.g., lower energy and operational costs, less environmental footprint, and more potential for small-scale ubiquitous installations. Several recent advancements in validating the feasibility of highly permeable gas separation membrane fabrication and system design show that membrane-based direct air capture (m-DAC) could be a complementary approach to sorbent-based DAC, e.g., as part of a hybrid system design that incorporates other DAC technologies (e.g., solvent or sorbent-based DAC). In this article, the ongoing research and DAC application attempts via membrane separation have been reviewed. The reported membrane materials that could potentially be used for m-DAC are summarized. In addition, the future direction of m-DAC development is discussed, which could provide perspective and encourage new researchers’ further work in the field of m-DAC. Full article

(This article belongs to the Special Issue Advanced Membrane Materials for CO₂ Capture and Separation)

► Show Figures

Figure 1

17 pages, 3101 KiB

Open AccessEditor’s ChoiceArticle

Development of a New Affinity Gold Polymer Membrane with Immobilized Protein A

by Tobias Steegmüller, Tim Kratky, Lena Gollwitzer, Sebastian Patrick Schwaminger and Sonja Berensmeier

Membranes 2024, 14(2), 31; https://doi.org/10.3390/membranes14020031 - 24 Jan 2024

Cited by 1 | Viewed by 2066

Abstract

New and highly selective stationary phases for affinity membrane chromatography have the potential to significantly enhance the efficiency and specificity of therapeutic protein purification by reduced mass transfer limitations. This work developed and compared different immobilization strategies for recombinant Protein A ligands to [...] Read more.

New and highly selective stationary phases for affinity membrane chromatography have the potential to significantly enhance the efficiency and specificity of therapeutic protein purification by reduced mass transfer limitations. This work developed and compared different immobilization strategies for recombinant Protein A ligands to a gold-sputtered polymer membrane for antibody separation in terms of functionalization and immobilization success, protein load, and stability. Successful, functionalization was validated via X-ray photoelectron spectroscopy (XPS). Here, a recombinant Protein A ligand was coupled by N-hydroxysuccinimide (NHS)/N-(3-dimethylaminopropyl)-N′-ethylcarbodiimide (EDC) chemistry to carboxy-functionalized, gold-sputtered membranes. We achieved a binding capacity of up to 104 ± 17 mg of the protein ligand per gram of the gold-sputtered membrane. The developed membranes were able to successfully capture and release the monoclonal antibody (mAb) Trastuzumab, as well as antibodies from fresh frozen human blood plasma in both static and dynamic setups. Therefore, they demonstrated successful functionalization and immobilization strategies. The antibody load was tested using bicinchoninic acid (BCA), ultraviolet-visible spectroscopy (UV-vis) measurements, and sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE). The outcome is a fully functional affinity membrane that can be implemented in a variety of different antibody purification processes, eliminating the need for creating individualized strategies for modifying the surface to suit different substrates or conditions. Full article

(This article belongs to the Special Issue Application of Advanced Membrane Materials in Bioseparation)

► Show Figures

Figure 1

21 pages, 1633 KiB

Open AccessEditor’s ChoiceReview

Simultaneous Wastewater Treatment and Resources Recovery by Forward Osmosis Coupled with Microbial Fuel Cell: A Review

by Hengliang Zhang, Liang Duan, Shilong Li, Qiusheng Gao, Mingyue Li, Fei Xing and Yang Zhao

Membranes 2024, 14(2), 29; https://doi.org/10.3390/membranes14020029 - 23 Jan 2024

Cited by 5 | Viewed by 2514

Abstract

Osmotic microbial fuel cells (OsMFCs) with the abilities to simultaneously treat wastewater, produce clean water, and electricity provided a novel approach for the application of microbial fuel cell (MFC) and forward osmosis (FO). This synergistic merging of functions significantly improved the performances of [...] Read more.

Osmotic microbial fuel cells (OsMFCs) with the abilities to simultaneously treat wastewater, produce clean water, and electricity provided a novel approach for the application of microbial fuel cell (MFC) and forward osmosis (FO). This synergistic merging of functions significantly improved the performances of OsMFCs. Nonetheless, despite their promising potential, OsMFCs currently receive inadequate attention in wastewater treatment, water reclamation, and energy recovery. In this review, we delved into the cooperation mechanisms between the MFC and the FO. MFC facilitates the FO process by promoting water flux, reducing reverse solute flux (RSF), and degrading contaminants in the feed solution (FS). Moreover, the water flux based on the FO principle contributed to MFC’s electricity generation capability. Furthermore, we summarized the potential roles of OsMFCs in resource recovery, including nutrient, energy, and water recovery, and identified the key factors, such as configurations, FO membranes, and draw solutions (DS). We prospected the practical applications of OsMFCs in the future, including their capabilities to remove emerging pollutants. Finally, we also highlighted the existing challenges in membrane fouling, system expansion, and RSF. We hope this review serves as a useful guide for the practical implementation of OsMFCs. Full article

(This article belongs to the Special Issue Advances in Modeling, Control, and Optimization of Membrane Distillation and Membrane Separation Processes)

► Show Figures

Figure 1

14 pages, 1804 KiB

Open AccessEditor’s ChoiceReview

The Application of Membrane Separation Technology in the Pharmaceutical Industry

by Ruirui Ma, Juan Li, Ping Zeng, Liang Duan, Jimin Dong, Yunxia Ma and Lingkong Yang

Membranes 2024, 14(1), 24; https://doi.org/10.3390/membranes14010024 - 17 Jan 2024

Cited by 5 | Viewed by 5010

Abstract

With the advancement in membrane technology, membrane separation technology has been found increasingly widespread applications in the pharmaceutical industry. It is utilized in drug separation and purification, wastewater treatment, and the recycling of wastewater resources. This study summarizes the application history of membrane [...] Read more.

With the advancement in membrane technology, membrane separation technology has been found increasingly widespread applications in the pharmaceutical industry. It is utilized in drug separation and purification, wastewater treatment, and the recycling of wastewater resources. This study summarizes the application history of membrane technology in the pharmaceutical industry, presents practical engineering examples of its applications, analyzes the various types of membrane technologies employed in the pharmaceutical sector, and finally, highlights the application cases of renowned international and Chinese membrane technology companies in the pharmaceutical field. Full article

(This article belongs to the Special Issue Sustainable Membrane Technologies for Wastewater Treatment)

► Show Figures

Figure 1

28 pages, 2689 KiB

Open AccessEditor’s ChoiceReview

Green Synthesis of Cation Exchange Membranes: A Review

by Stef Depuydt and Bart Van der Bruggen

Membranes 2024, 14(1), 23; https://doi.org/10.3390/membranes14010023 - 17 Jan 2024

Cited by 2 | Viewed by 4052

Abstract

Cation exchange membranes (CEMs) play a significant role in the transition to a more sustainable/green society. They are important components for applications such as water electrolysis, artificial photosynthesis, electrodialysis and fuel cells. Their synthesis, however, is far from being sustainable, affecting safety, health [...] Read more.

Cation exchange membranes (CEMs) play a significant role in the transition to a more sustainable/green society. They are important components for applications such as water electrolysis, artificial photosynthesis, electrodialysis and fuel cells. Their synthesis, however, is far from being sustainable, affecting safety, health and the environment. This review discusses and evaluates the possibilities of synthesizing CEMs that are more sustainable and green. First, the concepts of green and sustainable chemistry are discussed. Subsequently, this review discusses the fabrication of conventional perfluorinated CEMs and how they violate the green/sustainability principles, eventually leading to environmental and health incidents. Furthermore, the synthesis of green CEMs is presented by dividing the synthesis into three parts: sulfonation, material selection and solvent selection. Innovations in using gaseous SO3 or gas–liquid interfacial plasma technology can make the sulfonation process more sustainable. Regarding the selection of polymers, chitosan, cellulose, polylactic acid, alginate, carrageenan and cellulose are promising alternatives to fossil fuel-based polymers. Finally, water is the most sustainable solvent and many biopolymers are soluble in it. For other polymers, there are a limited number of studies using green solvents. Promising solvents are found back in other membrane, such as dimethyl sulfoxide, Cyrene™, Rhodiasolv^® PolarClean, TamiSolve NxG and γ-valerolactone. Full article

(This article belongs to the Special Issue Electrochemical Membranes: Materials, Characterization, Testing, and Cleaning)

► Show Figures

Graphical abstract

13 pages, 6584 KiB

Open AccessEditor’s ChoiceArticle

Effect of Long-Term Sodium Hypochlorite Cleaning on Silicon Carbide Ultrafiltration Membranes Prepared via Low-Pressure Chemical Vapor Deposition

by Asif Jan, Mingliang Chen, Michiel Nijboer, Mieke W. J. Luiten-Olieman, Luuk C. Rietveld and Sebastiaan G. J. Heijman

Membranes 2024, 14(1), 22; https://doi.org/10.3390/membranes14010022 - 15 Jan 2024

Viewed by 2806

Abstract

Sodium hypochlorite (NaClO) is widely used for the chemical cleaning of fouled ultrafiltration (UF) membranes. Various studies performed on polymeric membranes demonstrate that long-term (>100 h) exposure to NaClO deteriorates the physicochemical properties of the membranes, leading to reduced performance and service life. [...] Read more.

Sodium hypochlorite (NaClO) is widely used for the chemical cleaning of fouled ultrafiltration (UF) membranes. Various studies performed on polymeric membranes demonstrate that long-term (>100 h) exposure to NaClO deteriorates the physicochemical properties of the membranes, leading to reduced performance and service life. However, the effect of NaClO cleaning on ceramic membranes, particularly the number of cleaning cycles they can undergo to alleviate irreversible fouling, remains poorly understood. Silicon carbide (SiC) membranes have garnered widespread attention for water and wastewater treatment, but their chemical stability in NaClO has not been studied. Low-pressure chemical vapor deposition (LP-CVD) provides a simple and economical route to prepare/modify ceramic membranes. As such, LP-CVD facilitates the preparation of SiC membranes: (a) in a single step; and (b) at much lower temperatures (700–900 °C) in comparison with sol-gel methods (ca. 2000 °C). In this work, SiC ultrafiltration (UF) membranes were prepared via LP-CVD at two different deposition temperatures and pressures. Subsequently, their chemical stability in NaClO was investigated over 200 h of aging. Afterward, the properties and performance of as-prepared SiC UF membranes were evaluated before and after aging to determine the optimal deposition conditions. Our results indicate that the SiC UF membrane prepared via LP-CVD at 860 °C and 100 mTorr exhibited excellent resistance to NaClO aging, while the membrane prepared at 750 °C and 600 mTorr significantly deteriorated. These findings not only highlight a novel preparation route for SiC membranes in a single step via LP-CVD, but also provide new insights about the careful selection of LP-CVD conditions for SiC membranes to ensure their long-term performance and robustness under harsh chemical cleaning conditions. Full article

(This article belongs to the Special Issue Inorganic Membranes for Energy and Environmental Applications)

► Show Figures

Graphical abstract

17 pages, 14440 KiB

Open AccessEditor’s ChoiceArticle

Inducing Deep Sweeps and Vortex Ejections on Patterned Membrane Surfaces to Mitigate Surface Fouling

by August H. Young, Nico Hotz, Brian T. Hawkins and Zbigniew J. Kabala

Membranes 2024, 14(1), 21; https://doi.org/10.3390/membranes14010021 - 13 Jan 2024

Cited by 2 | Viewed by 1978

Abstract

Patterned membrane surfaces offer a hydrodynamic approach to mitigating concentration polarization and subsequent surface fouling. However, when subjected to steady crossflow conditions, surface patterns promote particle accumulation in the recirculation zones of cavity-like spaces. In order to resolve this issue, we numerically subject [...] Read more.

Patterned membrane surfaces offer a hydrodynamic approach to mitigating concentration polarization and subsequent surface fouling. However, when subjected to steady crossflow conditions, surface patterns promote particle accumulation in the recirculation zones of cavity-like spaces. In order to resolve this issue, we numerically subject a two-dimensional, patterned membrane surface to a rapidly pulsed crossflow. When combined with cavity-like spaces, such as the valleys of membrane surface patterns, a rapidly pulsed flow generates mixing mechanisms (i.e., the deep sweep and the vortex ejection) and disrupts recirculation zones. In only four pulses, we demonstrate the ability of these mechanisms to remove over half of the particles trapped in recirculation zones via massless particle tracking studies (i.e., numerical integration of the simulated velocity field). The results of this work suggest that when combined with a rapidly pulsed inlet flow, patterned membrane surfaces can not only alleviate concentration polarization and the surface fouling that follows but also reduce the need for traditional cleaning methods that require operational downtime and often involve the use of abrasive chemical agents. Full article

(This article belongs to the Special Issue Theoretical Study of Membrane Processes)

► Show Figures

Figure 1

13 pages, 2453 KiB

Open AccessEditor’s ChoiceArticle

Cannabidiol Strengthening of Gastric Tight Junction Complexes Analyzed in an Improved Xenopus Oocyte Assay

by Laura Stein, Marie-Luise Vollstaedt and Salah Amasheh

Membranes 2024, 14(1), 18; https://doi.org/10.3390/membranes14010018 - 8 Jan 2024

Cited by 1 | Viewed by 2184

Abstract

Cannabidiol (CBD), the non-psychoactive compound derived from the cannabis plant, has gained attention in recent years as a remedy against gastrointestinal disorders ranging from nausea and inflammation to abdominal pain. Recent advances demonstrated an effect on inflammatory pathways and barrier proteins. However, information [...] Read more.

Cannabidiol (CBD), the non-psychoactive compound derived from the cannabis plant, has gained attention in recent years as a remedy against gastrointestinal disorders ranging from nausea and inflammation to abdominal pain. Recent advances demonstrated an effect on inflammatory pathways and barrier proteins. However, information on possible direct effects is scarce and needs to be addressed, as applications are currently increasing in popularity. To accomplish this, we have employed Xenopus laevis oocytes as a heterologous expression system for analysis of the direct effects on stomach-specific claudins and further developed tight junction (TJ) protein interaction assays. Human claudin-4, claudin-5, and claudin-18.2 were expressed in Xenopus oocytes, clustered in pairs to form contact areas, and analyzed in a two-cell model approach, including measurement of the contact area and contact strength. CLDN4/5/18 + CLDN4/5/18 oocyte pairs were incubated with 20 µM CBD or with 40 µM CBD and were compared to cells without CBD treatment (ctrl). For interaction analysis, the contact area was measured after 24 h and 48 h. Whereas CBD did not affect the size of the protein interaction area, Double Orbital Challenge experiments revealed an increased contact strength after 24 h incubation with CBD. In addition, the Xenopus oocyte experiments were accompanied by an analysis of claudin-4, -5, and -18 expression in gastric epithelium by immunoblotting and immunohistochemistry. Claudin-4, -5, and -18 were strongly expressed, indicating a major role for gastric epithelial barrier function. In summary, our study shows direct effects of 40 µM CBD on Xenopus oocytes heterologously expressing a stomach-specific claudin combination, indicating a supportive and beneficial effect of CBD on gastric TJ proteins. Full article

(This article belongs to the Special Issue The Xenopus Oocyte: A Tool for Membrane Biology, Second Edition)

► Show Figures

Graphical abstract

16 pages, 5171 KiB

Open AccessEditor’s ChoiceArticle

Promising Fluorine-Free Ion Exchange Membranes Based on a Poly(ether-block-amide) Copolymer and Sulfonated Montmorillonite: Influence of Different Copolymer Segment Ratios

by Manhal H. Ibrahim Al-Mashhadani, Khirdakhanim Salmanzade, András Tompos and Asmaa Selim

Membranes 2024, 14(1), 17; https://doi.org/10.3390/membranes14010017 - 6 Jan 2024

Cited by 1 | Viewed by 2366

Abstract

Novel composite membranes employing a poly(ether-block-amide) (PEBAX) copolymer and sulfonated montmorillonite (S-MMT) as a filler were developed. The ratio of polyether to polyamide blocks was investigated using PEBAX 2533 and PEBAX 4533 based on the membrane properties and performance. Additionally, the effect of [...] Read more.

Novel composite membranes employing a poly(ether-block-amide) (PEBAX) copolymer and sulfonated montmorillonite (S-MMT) as a filler were developed. The ratio of polyether to polyamide blocks was investigated using PEBAX 2533 and PEBAX 4533 based on the membrane properties and performance. Additionally, the effect of the changing filler ratio was monitored. The interaction between the S-MMT as nanofiller and the polymer matrix of PEBAX2533 and PEBAX4533 as well as the crystalline nature and thermal and mechanical stability of the composite membranes were evaluated using Fourier Transform Infrared Spectroscopy (FT-IR), X-ray diffraction (XRD), thermogravimetric analysis (TGA), and tensile test. The composite membrane with 7 wt.% S-MMT showed the highest water uptake of 21% and 16% and an acceptable swelling degree of 16% and 9% for PEBAX 2533 and PEBAX 4533 composite membranes, respectively. In terms of water uptake and ion exchange capacity at room temperature, the new un-protonated membranes are superior to un-protonated Nafion. Meanwhile, with the same S-MMT content, the ion conductivity of PEBAX 2533 and PEBAX 4533 composite membranes is 2 and 1.6 mS/cm, and their ion exchange capacity is 0.9 and 1.10 meq/g. Full article

(This article belongs to the Special Issue Advanced Polymeric Membranes for Fuel Cell Applications)

► Show Figures

Figure 1

13 pages, 4179 KiB

Open AccessEditor’s ChoiceArticle

High-Degree Concentration Organic Solvent Forward Osmosis for Pharmaceutical Pre-Concentration

by Ryoichi Takada, Ryosuke Takagi and Hideto Matsuyama

Membranes 2024, 14(1), 14; https://doi.org/10.3390/membranes14010014 - 4 Jan 2024

Cited by 2 | Viewed by 1995

Abstract

Over half of the pharmaceutical industry’s capital investments are related to the purification of active pharmaceutical ingredients (APIs). Thus, a cost-effective purification process with a highly concentrated solution is urgently required. In addition, the purification process should be nonthermal because most APIs and [...] Read more.

Over half of the pharmaceutical industry’s capital investments are related to the purification of active pharmaceutical ingredients (APIs). Thus, a cost-effective purification process with a highly concentrated solution is urgently required. In addition, the purification process should be nonthermal because most APIs and their intermediates are temperature-sensitive. This study investigated a high-degree concentration organic solvent forward osmosis (OSFO) membrane process. A polyketone-based thin-film composite hollow fiber membrane with a polyamide selective layer on the bore surface was used as the OSFO membrane to achieve a high tolerance for organic solvents and an effective concentration. MeOH, sucrose octaacetate (SoA), and 2M polyethylene glycol 400 (PEG-400)/MeOH solution were used as the solvent, model API, and a draw solution (DS), respectively. OSFO was performed at room temperature (23 ± 3 °C). Consequently, the 11 wt% SoA/MeOH solution was concentrated to 52 wt% without any SoA leakage into the DS. To our knowledge, there are no studies in which up to a 5 wt% concentration by OSFO has been demonstrated. However, the final feed solution contained 17 wt% PEG-400. This study demonstrates the promising potential of OSFO for pharmaceutical pre-concentration and the technical problems that need to be solved for social implementation. Full article

(This article belongs to the Special Issue Development and Application of Membrane Separation Processes, 2nd Edition)

► Show Figures

Graphical abstract

15 pages, 2946 KiB

Open AccessEditor’s ChoiceArticle

Antibacterial Activity Assessment of Chitosan/Alginate Lavender Essential Oil Membranes for Biomedical Applications

by Encarnación Cruz Sánchez, María Teresa García, Ignacio Gracia, Soledad Illescas Fernández-Bermejo, Juan Francisco Rodríguez, Jesús Manuel García-Vargas and Dolors Vidal Roig

Membranes 2024, 14(1), 12; https://doi.org/10.3390/membranes14010012 - 1 Jan 2024

Cited by 2 | Viewed by 2682

Abstract

The demand for natural products in the treatment of dermatological pathologies has boosted the use of bioactive substances such as lavender essential oil (LEO), which stands out for its anti-inflammatory and antioxidant properties and its antimicrobial potential. Biopolymers such as chitosan (CHT) and [...] Read more.

The demand for natural products in the treatment of dermatological pathologies has boosted the use of bioactive substances such as lavender essential oil (LEO), which stands out for its anti-inflammatory and antioxidant properties and its antimicrobial potential. Biopolymers such as chitosan (CHT) and alginate (ALG) are biodegradable and biocompatible and have proven their viability in biomedical applications such as skin regeneration. The inhibitory effect of LEO on the growth of skin-related bacterial species Staphylococcus aureus, Staphylococcus epidermidis, Pseudomonas aeruginosa and the fungus Candida albicans was studied by incorporating 1% v/v LEO encapsulated in CHT, ALG, and CHT/ALG membranes. Despite the verification of the antimicrobial effect of all type of membranes, no synergistic effect was observed following the addition of LEO. S. aureus and P. aeruginosa showed the most growth on the different substrates and C. albicans demonstrated the highest inhibition. This is a first approach using microorganisms isolated from clinical samples or skin microbiota. Further investigation would be advisable using more clinical strains for each microorganism to validate their biomedical applicability. Full article

► Show Figures

Graphical abstract

27 pages, 5353 KiB

Open AccessEditor’s ChoiceReview

Membrane-Based Technologies for Post-Combustion CO₂ Capture from Flue Gases: Recent Progress in Commonly Employed Membrane Materials

by Petros Gkotsis, Efrosini Peleka and Anastasios Zouboulis

Membranes 2023, 13(12), 898; https://doi.org/10.3390/membranes13120898 - 2 Dec 2023

Cited by 12 | Viewed by 10470

Abstract

Carbon dioxide (CO₂), which results from fossil fuel combustion and industrial processes, accounts for a substantial part of the total anthropogenic greenhouse gases (GHGs). As a result, several carbon capture, utilization and storage (CCUS) technologies have been developed during the last [...] Read more.

Carbon dioxide (CO₂), which results from fossil fuel combustion and industrial processes, accounts for a substantial part of the total anthropogenic greenhouse gases (GHGs). As a result, several carbon capture, utilization and storage (CCUS) technologies have been developed during the last decade. Chemical absorption, adsorption, cryogenic separation and membrane separation are the most widely used post-combustion CO₂ capture technologies. This study reviews post-combustion CO₂ capture technologies and the latest progress in membrane processes for CO₂ separation. More specifically, the objective of the present work is to present the state of the art of membrane-based technologies for CO₂ capture from flue gases and focuses mainly on recent advancements in commonly employed membrane materials. These materials are utilized for the fabrication and application of novel composite membranes or mixed-matrix membranes (MMMs), which present improved intrinsic and surface characteristics and, thus, can achieve high selectivity and permeability. Recent progress is described regarding the utilization of metal–organic frameworks (MOFs), carbon molecular sieves (CMSs), nanocomposite membranes, ionic liquid (IL)-based membranes and facilitated transport membranes (FTMs), which comprise MMMs. The most significant challenges and future prospects of implementing membrane technologies for CO₂ capture are also presented. Full article

(This article belongs to the Special Issue Advances in Modeling, Control, and Optimization of Membrane Distillation and Membrane Separation Processes)

► Show Figures

Figure 1

20 pages, 8184 KiB

Open AccessEditor’s ChoiceArticle

Surface-Modified Pore-Filled Anion-Exchange Membranes for Efficient Energy Harvesting via Reverse Electrodialysis

by Ji-Hyeon Lee, Do-Hyeong Kim and Moon-Sung Kang

Membranes 2023, 13(12), 894; https://doi.org/10.3390/membranes13120894 - 30 Nov 2023

Cited by 3 | Viewed by 2255

Abstract

In this study, novel pore-filled anion-exchange membranes (PFAEMs) modified with polypyrrole (PPy) and reduced graphene oxide (rGO) were developed to improve the energy harvesting performance of reverse electrodialysis (RED). The surface-modified PFAEMs were fabricated by varying the contents of PPy and rGO through [...] Read more.

In this study, novel pore-filled anion-exchange membranes (PFAEMs) modified with polypyrrole (PPy) and reduced graphene oxide (rGO) were developed to improve the energy harvesting performance of reverse electrodialysis (RED). The surface-modified PFAEMs were fabricated by varying the contents of PPy and rGO through simple spin coating and chemical/thermal treatments. It was confirmed that the PPy and PPy/rGO layers introduced on the membrane surface did not significantly increase the electrical resistance of the membrane and could effectively control surface characteristics, such as structural tightness, hydrophilicity, and electrostatic repulsion. The PPy/rGO-modified PFAEM showed excellent monovalent ion selectivity, more than four times higher than that of the commercial membrane (AMX, Astom Corp., Tokyo, Japan). This means that the PPy/rGO layer can effectively reduce the permeation of multivalent ions with a high charge intensity and a relatively large hydration radius compared to monovalent ions. The results of evaluating the performance of the surface-modified PFAEMs by applying them to a RED cell revealed that the decrease in potential difference occurring in the membrane was reduced by effectively suppressing the uphill transport of multivalent ions. Consequently, the PPy/rGO-modified membrane exhibited a 5.43% higher power density than the AMX membrane. Full article

(This article belongs to the Special Issue Surface Modification of Ion Exchange Membranes)

► Show Figures

Graphical abstract

17 pages, 8117 KiB

Open AccessEditor’s ChoiceArticle

Heterogeneous Anion-Exchange Membranes with Enhanced Ion Conductivity for Continuous Electrodeionization

by Ji-Min Lee and Moon-Sung Kang

Membranes 2023, 13(12), 888; https://doi.org/10.3390/membranes13120888 - 27 Nov 2023

Cited by 2 | Viewed by 3286

Abstract

In this study, the optimal fabrication parameters of a heterogeneous anion-exchange membrane (AEM) using an ionomer binder are investigated to improve the performance of continuous electrodeionization (CEDI) for producing ultrapure water. Poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) is selected as the base material for preparing the [...] Read more.

In this study, the optimal fabrication parameters of a heterogeneous anion-exchange membrane (AEM) using an ionomer binder are investigated to improve the performance of continuous electrodeionization (CEDI) for producing ultrapure water. Poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) is selected as the base material for preparing the ionomer binder and quaternized to have various ion exchange capacities (IECs). The optimal content of ion-exchange resin (IER) powder according to the IEC of the ionomer binder is then determined through systematic analyses. In conclusion, it is revealed that a heterogeneous AEM with optimal performance can be fabricated when the IEC of the ionomer binder is lowered and the content of IER powder is also lower than that of conventional heterogeneous membranes. Moreover, crosslinked quaternized PPO (QPPO) nanofiber powder is used as an additive to improve ion conductivity without deteriorating the mechanical properties of the membrane. The membrane fabricated under optimal conditions exhibits significantly lower electrical resistance (4.6 Ω cm²) despite a low IER content (30 wt%) compared to the commercial membrane (IONAC MA-3475, 13.6 Ω cm²) while also demonstrating moderate tensile strength (9.7 MPa) and a high transport number (ca. 0.97). Furthermore, it is proven that the prepared membrane exhibits a superior ion removal rate (99.86%) and lower energy consumption (0.35 kWh) compared to the commercial membrane (99.76% and 0.4 kWh, respectively) in CEDI experiments. Full article

(This article belongs to the Section Polymeric Membranes)

► Show Figures

Graphical abstract

18 pages, 2604 KiB

Open AccessEditor’s ChoiceArticle

The Effect of Calcium Ions on hIAPP Channel Activity: Possible Implications in T2DM

by Daniela Meleleo, Giuseppe Cibelli, Anna Valenzano, Maria Mastrodonato and Rosanna Mallamaci

Membranes 2023, 13(11), 878; https://doi.org/10.3390/membranes13110878 - 9 Nov 2023

Cited by 1 | Viewed by 1941

Abstract

The calcium ion (Ca²⁺) has been linked to type 2 diabetes mellitus (T2DM), although the role of Ca²⁺ in this disorder is the subject of intense investigation. Serum Ca²⁺ dyshomeostasis is associated with the development of insulin resistance, reduced [...] Read more.

The calcium ion (Ca²⁺) has been linked to type 2 diabetes mellitus (T2DM), although the role of Ca²⁺ in this disorder is the subject of intense investigation. Serum Ca²⁺ dyshomeostasis is associated with the development of insulin resistance, reduced insulin sensitivity, and impaired glucose tolerance. However, the molecular mechanisms involving Ca²⁺ ions in pancreatic β-cell loss and subsequently in T2DM remain poorly understood. Implicated in the decline in β-cell functions are aggregates of human islet amyloid polypeptide (hIAPP), a small peptide secreted by β-cells that shows a strong tendency to self-aggregate into β-sheet-rich aggregates that evolve toward the formation of amyloid deposits and mature fibrils. The soluble oligomers of hIAPP can permeabilize the cell membrane by interacting with bilayer lipids. Our study aimed to evaluate the effect of Ca²⁺ on the ability of the peptide to incorporate and form ion channels in zwitterionic planar lipid membranes (PLMs) composed of palmitoyl-oleoyl-phosphatidylcholine (POPC) and on the aggregation process of hIAPP molecules in solution. Our results may help to clarify the link between Ca²⁺ ions, hIAPP peptide, and consequently the pathophysiology of T2DM. Full article

(This article belongs to the Special Issue Structure-Function Relationships and Biological Processes of Membrane Proteins)

► Show Figures

Graphical abstract

22 pages, 1869 KiB

Open AccessEditor’s ChoiceReview

Adsorptive Membranes Incorporating Ionic Liquids (ILs), Deep Eutectic Solvents (DESs) or Graphene Oxide (GO) for Metal Salts Extraction from Aqueous Feed

by Liyan Qalyoubi, Ioannis Zuburtikudis, Hadil Abu Khalifeh and Enas Nashef

Membranes 2023, 13(11), 874; https://doi.org/10.3390/membranes13110874 - 3 Nov 2023

Cited by 4 | Viewed by 2387

Abstract

Water scarcity is a significant concern, particularly in arid regions, due to the rapid growth in population, industrialization, and climate change. Seawater desalination has emerged as a conventional and reliable solution for obtaining potable water. However, conventional membrane-based seawater desalination has drawbacks, such [...] Read more.

Water scarcity is a significant concern, particularly in arid regions, due to the rapid growth in population, industrialization, and climate change. Seawater desalination has emerged as a conventional and reliable solution for obtaining potable water. However, conventional membrane-based seawater desalination has drawbacks, such as high energy consumption resulting from a high-pressure requirement, as well as operational challenges like membrane fouling and high costs. To overcome these limitations, it is crucial to enhance the performance of membranes by increasing their efficiency, selectivity, and reducing energy consumption and footprint. Adsorptive membranes, which integrate adsorption and membrane technologies, offer a promising approach to address the drawbacks of standalone membranes. By incorporating specific materials into the membrane matrix, composite membranes have demonstrated improved permeability, selectivity, and reduced pressure requirements, all while maintaining effective pollutant rejection. Researchers have explored different adsorbents, including emerging materials such as ionic liquids (ILs), deep eutectic solvents (DESs), and graphene oxide (GO), for embedding into membranes and utilizing them in various applications. This paper aims to discuss the existing challenges in the desalination process and focus on how these materials can help overcome these challenges. It will also provide a comprehensive review of studies that have reported the successful incorporation of ILs, DESs, and GO into membranes to fabricate adsorptive membranes for desalination. Additionally, the paper will highlight both the current and anticipated challenges in this field, as well as present prospects, and provide recommendations for further advancements. Full article

► Show Figures

Figure 1

16 pages, 6238 KiB

Open AccessEditor’s ChoiceArticle

High-Performance FAU Zeolite Membranes Derived from Nano-Seeds for Gas Separation

by Qing Wang, Huiyuan Chen, Feiyang He, Qiao Liu, Nong Xu, Long Fan, Chuyan Wang, Lingyun Zhang and Rongfei Zhou

Membranes 2023, 13(11), 858; https://doi.org/10.3390/membranes13110858 - 26 Oct 2023

Cited by 5 | Viewed by 3206

Abstract

In this study, high-performance FAU (NaY type) zeolite membranes were successfully synthesized using small-sized seeds of 50 nm, and their gas separation performance was systematically evaluated. Employing nano-sized NaY seeds and an ultra-dilute reaction solution with a molar composition of 80 Na₂ [...] Read more.

In this study, high-performance FAU (NaY type) zeolite membranes were successfully synthesized using small-sized seeds of 50 nm, and their gas separation performance was systematically evaluated. Employing nano-sized NaY seeds and an ultra-dilute reaction solution with a molar composition of 80 Na₂O: 1Al₂O₃: 19 SiO₂: 5000H₂O, the effects of synthesis temperature, crystallization time, and porous support (α-Al₂O₃ or mullite) on the formation of FAU membranes were investigated. The results illustrated that further extending the crystallization time or increasing the synthesis temperature led to the formation of a NaP impurity phase on the FAU membrane layer. The most promising FAU membrane with a thickness of 2.7 µm was synthesized on an α-Al₂O₃ support at 368 K for 8 h and had good reproducibility. The H₂ permeance of the membrane was as high as 5.34 × 10⁻⁷ mol/(m² s Pa), and the H₂/C₃H₈ and H₂/i-C₄H₁₀ selectivities were 183 and 315, respectively. The C₃H₆/C₃H₈ selectivity of the membrane was as high as 46, with a remarkably high C₃H₆ permeance of 1.35 × 10⁻⁷ mol/(m² s Pa). The excellent separation performance of the membrane is mainly attributed to the thin, defect-free membrane layer and the relatively wide pore size (0.74 nm). Full article

(This article belongs to the Section Membrane Applications)

► Show Figures

Figure 1

18 pages, 1327 KiB

Open AccessEditor’s ChoiceReview

The Latest Achievements of Liquid Membranes for Rare Earth Elements Recovery from Aqueous Solutions—A Mini Review

by Małgorzata A. Kaczorowska

Membranes 2023, 13(10), 839; https://doi.org/10.3390/membranes13100839 - 21 Oct 2023

Cited by 5 | Viewed by 2770

Abstract

The systematic increase in the use of rare earth elements (REEs) in various technologically advanced products around the world (e.g., in electronic devices), the growing amount of waste generated by the use of high-tech materials, and the limited resources of naturally occurring REE [...] Read more.

The systematic increase in the use of rare earth elements (REEs) in various technologically advanced products around the world (e.g., in electronic devices), the growing amount of waste generated by the use of high-tech materials, and the limited resources of naturally occurring REE ores resulted in an intensive search for effective and environmentally safe methods for recovering these elements. Among these methods, techniques based on the application of various types of liquid membranes (LMs) play an important role, primarily due to their high efficiency, the simplicity of membrane formation and use, the utilization of only small amounts of environmentally hazardous reagents, and the possibility of simultaneous extraction and back-extraction and reusing the membranes after regeneration. However, because both primary and secondary sources (e.g., waste) of REEs are usually complex and contain a wide variety of components, and the selectivity and efficiency of LMs depend on many factors (e.g., the composition and form of the membrane, nature of the recovered ions, composition of the feed and stripping phases, etc.), new membranes are being developed that are “tailored” to the properties of the recovered rare earth elements and to the character of the solution in which they occur. This review describes the latest achievements (since 2019) related to the recovery of a range of REEs with the use of various liquid membranes (supported liquid membranes (SLMs), emulsion liquid membranes (ELMs), and polymer inclusion membranes (PIMs)), with particular emphasis on methods that fall within the trend of eco-friendly solutions. Full article

(This article belongs to the Special Issue Membrane Systems for Metal Ion Extraction)

► Show Figures

Figure 1

15 pages, 2596 KiB

Open AccessEditor’s ChoiceReview

A Comprehensive Analysis of the Impact of Inorganic Matter on Membrane Organic Fouling: A Mini Review

by Qiusheng Gao, Liang Duan, Yanyan Jia, Hengliang Zhang, Jianing Liu and Wei Yang

Membranes 2023, 13(10), 837; https://doi.org/10.3390/membranes13100837 - 20 Oct 2023

Cited by 5 | Viewed by 2351

Abstract

Membrane fouling is a non-negligible issue affecting the performance of membrane systems. Particularly, organic fouling is the most persistent and severe form of fouling. The complexation between inorganic and organic matter may exacerbate membrane organic fouling. This mini review systematically analyzes the role [...] Read more.

Membrane fouling is a non-negligible issue affecting the performance of membrane systems. Particularly, organic fouling is the most persistent and severe form of fouling. The complexation between inorganic and organic matter may exacerbate membrane organic fouling. This mini review systematically analyzes the role of inorganic matter in membrane organic fouling. Inorganic substances, such as metal ions and silica, can interact with organic foulants like humic acids, polysaccharides, and proteins through ionic bonding, hydrogen bonding, coordination, and van der Waals interactions. These interactions facilitate the formation of larger aggregates that exacerbate fouling, especially for reverse osmosis membranes. Molecular simulations using molecular dynamics (MD) and density functional theory (DFT) provide valuable mechanistic insights complementing fouling experiments. Polysaccharide fouling is mainly governed by transparent exopolymer particle (TEP) formations induced by inorganic ion bridging. Inorganic coagulants like aluminum and iron salts mitigate fouling for ultrafiltration but not reverse osmosis membranes. This review summarizes the effects of critical inorganic constituents on fouling by major organic foulants, providing an important reference for membrane fouling modeling and fouling control strategies. Full article

(This article belongs to the Special Issue Membrane Separation Systems: Design and Applications)

► Show Figures

Figure 1

25 pages, 5593 KiB

Open AccessEditor’s ChoiceReview

A Recent Review of Electrospun Porous Carbon Nanofiber Mats for Energy Storage and Generation Applications

by Al Mamun, Mohamed Kiari and Lilia Sabantina

Membranes 2023, 13(10), 830; https://doi.org/10.3390/membranes13100830 - 13 Oct 2023

Cited by 7 | Viewed by 3017

Abstract

Electrospun porous carbon nanofiber mats have excellent properties, such as a large surface area, tunable porosity, and excellent electrical conductivity, and have attracted great attention in energy storage and power generation applications. Moreover, due to their exceptional properties, they can be used in [...] Read more.

Electrospun porous carbon nanofiber mats have excellent properties, such as a large surface area, tunable porosity, and excellent electrical conductivity, and have attracted great attention in energy storage and power generation applications. Moreover, due to their exceptional properties, they can be used in dye-sensitized solar cells (DSSCs), membrane electrodes for fuel cells, catalytic applications such as oxygen reduction reactions (ORRs), hydrogen evolution reactions (HERs), and oxygen evolution reactions (OERs), and sensing applications such as biosensors, electrochemical sensors, and chemical sensors, providing a comprehensive insight into energy storage development and applications. This study focuses on the role of electrospun porous carbon nanofiber mats in improving energy storage and generation and contributes to a better understanding of the fabrication process of electrospun porous carbon nanofiber mats. In addition, a comprehensive review of various alternative preparation methods covering a wide range from natural polymers to synthetic carbon-rich materials is provided, along with insights into the current literature. Full article

(This article belongs to the Special Issue Nanofibrous Membrane for Biomedical, Environmental and Energy Application)

► Show Figures

Figure 1

15 pages, 8704 KiB

Open AccessEditor’s ChoiceArticle

Differences in the Effect of Mn²⁺ on the Reverse Osmosis Membrane Fouling Caused by Different Types of Organic Matter: Experimental and Density Functional Theory Evidence

by Qiusheng Gao, Liang Duan, Yanyan Jia, Hengliang Zhang, Jianing Liu and Wei Yang

Membranes 2023, 13(10), 823; https://doi.org/10.3390/membranes13100823 - 5 Oct 2023

Cited by 3 | Viewed by 1978

Abstract

Landfill leachate from some sites contains a high concentration of Mn²⁺, which may cause reverse osmosis (RO) membrane fouling during RO treatment. In this study, the effect of Mn²⁺ on RO membrane fouling caused by typical organic pollutants (humic acid [...] Read more.

Landfill leachate from some sites contains a high concentration of Mn²⁺, which may cause reverse osmosis (RO) membrane fouling during RO treatment. In this study, the effect of Mn²⁺ on RO membrane fouling caused by typical organic pollutants (humic acid (HA), protein (BSA), and sodium alginate (SA)) was systematically investigated, and it was found that Mn²⁺ exacerbates RO membrane fouling caused by HA, SA, and HBS (mixture of HA + BSA + SA). When the Mn²⁺ concentration was 0.5 mM and 0.05 mM separately, the membrane fouling caused by HA and SA began to become significant. On the other hand, with for HBS fouling only, the water flux decreased significantly by about 21.7% and further decreased with an increasing Mn²⁺ concentration. However, Mn²⁺ has no direct effect on BSA. The effect degrees to which Mn²⁺ affected RO membrane fouling can be expressed as follows: HBS > SA > HA > BSA. The density functional theory (DFT) calculations also gave the same results. In modeling the reaction of the complexation of Mn²⁺ with the carboxyl group in these four types of organic matter, BSA has the highest energy (−55.7 kJ/mol), which predicts that BSA binding to Mn²⁺ is the most unstable compared to other organic matter. The BSA carboxylate group also has the largest bond length (2.538–2.574 Å) with Mn²⁺ and the weakest interaction force, which provides a theoretical basis for controlling RO membrane fouling exacerbated by Mn²⁺. Full article

(This article belongs to the Special Issue Membrane Separation Systems: Design and Applications)

► Show Figures

Figure 1

18 pages, 2146 KiB

Open AccessEditor’s ChoiceArticle

Polymeric Inclusion Membranes Based on Ionic Liquids for Selective Separation of Metal Ions

by Adrián Hernández-Fernández, Eduardo Iniesta-López, Anahí Ginestá-Anzola, Yolanda Garrido, Antonia Pérez de los Ríos, Joaquín Quesada-Medina and Francisco José Hernández-Fernández

Membranes 2023, 13(9), 795; https://doi.org/10.3390/membranes13090795 - 13 Sep 2023

Cited by 3 | Viewed by 2019

Abstract

In this work, poly(vinyl chloride)-based polymeric ionic liquid inclusion membranes were used in the selective separation of Fe(III), Zn(II), Cd(II), and Cu(II) from hydrochloride aqueous solutions. The ionic liquids under study were 1-octyl-3-methylimidazolium hexafluorophosphate, [omim⁺][PF₆⁻] and methyl trioctyl [...] Read more.

In this work, poly(vinyl chloride)-based polymeric ionic liquid inclusion membranes were used in the selective separation of Fe(III), Zn(II), Cd(II), and Cu(II) from hydrochloride aqueous solutions. The ionic liquids under study were 1-octyl-3-methylimidazolium hexafluorophosphate, [omim⁺][PF₆⁻] and methyl trioctyl ammonium chloride, [MTOA⁺][Cl⁻]. For this purpose, stability studies of different IL/base polymer compositions against aqueous phases were carried out. Among all polymer inclusion membranes studied, [omim⁺][PF₆⁻]/PVC membranes at a ratio of 30/70 and [MTOA⁺][Cl⁻]/PVC membranes at a ratio of 70/30 were able to retain up to 82% and 48% of the weight of the initial ionic liquid, respectively, after being exposed to a solution of metal ions in 1 M HCl for 2048 h (85 days). It was found that polymer inclusion membranes based on the ionic liquid methyl trioctyl ammonium chloride allowed the selective separation of Zn(II)/Cu(II) and Zn(II)/Fe(III) mixtures with separation factors of 1996, 606 and, to a lesser extent but also satisfactorily, Cd(II)/Cu(II) mixtures, with a separation factor of 112. Therefore, selecting the appropriate ionic liquid/base polymer mixture makes it possible to create polymeric inclusion membranes capable of selectively separating target metal ions. Full article

(This article belongs to the Special Issue Advances in Modeling, Control, and Optimization of Membrane Distillation and Membrane Separation Processes)

► Show Figures

Figure 1

16 pages, 1640 KiB

Open AccessEditor’s ChoiceArticle

Ultrafiltration and Nanofiltration for the Removal of Pharmaceutically Active Compounds from Water: The Effect of Operating Pressure on Electrostatic Solute—Membrane Interactions

by Alexandre Giacobbo, Isabella Franco Pasqualotto, Rafael Cabeleira de Coronel Machado Filho, Miguel Minhalma, Andréa Moura Bernardes and Maria Norberta de Pinho

Membranes 2023, 13(8), 743; https://doi.org/10.3390/membranes13080743 - 19 Aug 2023

Cited by 7 | Viewed by 2120

Abstract

The present work investigates nanofiltration (NF) and ultrafiltration (UF) for the removal of three widely used pharmaceutically active compounds (PhACs), namely atenolol, sulfamethoxazole, and rosuvastatin. Four membranes, two polyamide NF membranes (NF90 and NF270) and two polyethersulfone UF membranes (XT and ST), were [...] Read more.

The present work investigates nanofiltration (NF) and ultrafiltration (UF) for the removal of three widely used pharmaceutically active compounds (PhACs), namely atenolol, sulfamethoxazole, and rosuvastatin. Four membranes, two polyamide NF membranes (NF90 and NF270) and two polyethersulfone UF membranes (XT and ST), were evaluated in terms of productivity (permeate flux) and selectivity (rejection of PhACs) at pressures from 2 to 8 bar. Although the UF membranes have a much higher molecular weight cut-off (1000 and 10,000 Da), when compared to the molecular weight of the PhACs (253–482 Da), moderate rejections were observed. For UF, rejections were dependent on the molecular weight and charge of the PhACs, membrane molecular weight cut-off (MWCO), and operating pressure, demonstrating that electrostatic interactions play an important role in the removal of PhACs, especially at low operating pressures. On the other hand, both NF membranes displayed high rejections for all PhACs studied (75–98%). Hence, considering the optimal operating conditions, the NF270 membrane (MWCO = 400 Da) presented the best performance, achieving permeate fluxes of about 100 kg h⁻¹ m⁻² and rejections above 80% at a pressure of 8 bar, that is, a productivity of about twice that of the NF90 membrane (MWCO = 200 Da). Therefore, NF270 was the most suitable membrane for this application, although the tight UF membranes under low operating pressures displayed satisfactory results. Full article

(This article belongs to the Special Issue Honorary Issue for Prof João G. Crespo)

► Show Figures

Figure 1

21 pages, 2447 KiB

Open AccessEditor’s ChoiceArticle

MID-FTIR-PLS Chemometric Analysis of Cr(VI) from Aqueous Solutions Using a Polymer Inclusion Membrane-Based Sensor

by Armando Martínez de la Peña, Eduardo Rodríguez de San Miguel and Josefina de Gyves

Membranes 2023, 13(8), 740; https://doi.org/10.3390/membranes13080740 - 18 Aug 2023

Cited by 3 | Viewed by 1511

Abstract

A partial least squares (PLS) quantitative chemometric method based on the analysis of the mid-Fourier transform infrared spectroscopy (MID-FTIR) spectrum of polymer inclusion membranes (PIMs) used for the extraction of Cr(VI) from aqueous media is developed. The system previously optimized considering the variables [...] Read more.

A partial least squares (PLS) quantitative chemometric method based on the analysis of the mid-Fourier transform infrared spectroscopy (MID-FTIR) spectrum of polymer inclusion membranes (PIMs) used for the extraction of Cr(VI) from aqueous media is developed. The system previously optimized considering the variables membrane composition, extraction time, and pH, is characterized in terms of its adsorption isotherm, distribution coefficient, extraction percent, and enrichment factor. A Langmuir-type adsorption behavior with K_L = 2199 cm³/mmol, q_max = 0.188 mmol/g, and 0 < R_L < 1 indicates that metal adsorption is favorable. The characterization of the extraction reaction is performed as well, showing a 1:1 Cr(VI):Aliquat 336 ratio, in agreement with solvent extraction data. The principal component analysis (PCA) of the PIMs reveals a complex pattern, which is satisfactorily simplified and related to Cr(VI) concentrations through the use of a variable selection method (iPLS) in which the bands in the ranges 3451–3500 cm⁻¹ and 3751–3800 cm⁻¹ are chosen. The final PLS model, including the 100 wavelengths selected by iPLS and 10 latent variables, shows excellent parameter values with root mean square error of calibration (RMSEC) of 3.73115, root mean square error of cross-validation (RMSECV) of 6.82685, bias of −1.91847 × 10⁻¹³, cross-validation (CV) bias of 0.185947, R² Cal of 0.98145, R² CV of 0.940902, recovery% of 104.02 ± 4.12 (α = 0.05), sensitivity% of 0.001547 ppb, analytical sensitivity (γ) of 3.8 ppb, γ⁻¹: 0.6 ppb⁻¹, selectivity of 0.0155, linear range of 5.8–100 ppb, limit of detection (LD) of 1.9 ppb, and limit of quantitation (LQ) of 5.8 ppb. The developed PIM sensor is easy to implement as it requires few manipulations and a reduced number of chemical compounds in comparison to other similar reported systems. Full article

(This article belongs to the Special Issue New Trends in Polymer Inclusion Membranes 2.0)

► Show Figures

Figure 1

41 pages, 4959 KiB

Open AccessEditor’s ChoiceReview

Large-Scale Synthesis of Covalent Organic Frameworks: Challenges and Opportunities

by Harsh Vardhan, Grace Rummer, Angela Deng and Shengqian Ma

Membranes 2023, 13(8), 696; https://doi.org/10.3390/membranes13080696 - 27 Jul 2023

Cited by 11 | Viewed by 4705

Abstract

Connecting organic building blocks by covalent bonds to design porous crystalline networks has led to covalent organic frameworks (COFs), consequently transferring the flexibility of dynamic linkages from discrete architectures to extended structures. By virtue of the library of organic building blocks and the [...] Read more.

Connecting organic building blocks by covalent bonds to design porous crystalline networks has led to covalent organic frameworks (COFs), consequently transferring the flexibility of dynamic linkages from discrete architectures to extended structures. By virtue of the library of organic building blocks and the diversity of dynamic linkages and topologies, COFs have emerged as a novel field of organic materials that propose a platform for tailor-made complex structural design. Progress over the past two decades in the design, synthesis, and functional exploration of COFs in diverse applications successively established these frameworks in materials chemistry. The large-scale synthesis of COFs with uniform structures and properties is of profound importance for commercialization and industrial applications; however, this is in its infancy at present. An innovative designing and synthetic approaches have paved novel ways to address future hurdles. This review article highlights the fundamental of COFs, including designing principles, coupling reactions, topologies, structural diversity, synthetic strategies, characterization, growth mechanism, and activation aspects of COFs. Finally, the major challenges and future trends for large-scale COF fabrication are outlined. Full article

(This article belongs to the Special Issue Porous MOF/COF for Membrane Applications)

► Show Figures

Graphical abstract

16 pages, 11361 KiB

Open AccessEditor’s ChoiceArticle

In Situ Formation of Silver Nanoparticles Induced by Cl-Doped Carbon Quantum Dots for Enhanced Separation and Antibacterial Performance of Nanofiltration Membrane

by Yi-Fang Mi, Jia-Li Liu, Wen Xia, Shu-Heng He and Bao-Qing Shentu

Membranes 2023, 13(8), 693; https://doi.org/10.3390/membranes13080693 - 25 Jul 2023

Cited by 4 | Viewed by 1353

Abstract

Polyamide (PA) nanofiltration (NF) membranes suffer from biofouling, which will deteriorate their separation performance. In this study, we proposed a strategy to incorporate silver nanoparticles (Ag NPs) into PA NF membranes in situ, in order to simultaneously enhance water permeability and antibacterial performance. [...] Read more.

Polyamide (PA) nanofiltration (NF) membranes suffer from biofouling, which will deteriorate their separation performance. In this study, we proposed a strategy to incorporate silver nanoparticles (Ag NPs) into PA NF membranes in situ, in order to simultaneously enhance water permeability and antibacterial performance. The chloride-doped carbon quantum dots (Cl-CQDs) with photocatalytic performance were pre-embedded in the PA selective layer. Under visible light irradiation, the photogenerated charge carriers generated by Cl-CQDs rapidly transported to silver ions (Ag⁺ ions), resulting in the in situ formation of Ag NPs. The proposed strategy avoided the problem of aggregating Ag NPs, and the amount of Ag NPs on the membrane surfaces could be easily tuned by changing silver nitrate (AgNO₃) concentrations and immersion times. These uniformly dispersed Ag NPs increased membrane hydrophilicity. Thus, the obtained thin film nanocomposite Ag NPs (TFN-Ag) membrane exhibited an improved water flux (31.74 L m⁻² h⁻¹), which was ~2.98 times that of the pristine PA membrane; meanwhile, the sodium sulfate (Na₂SO₄) rejection rate was 96.11%. The sterilization rates of the TFN-Ag membrane against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) were 99.55% and 99.52%, respectively. Thus, this facile strategy simultaneously improved the permeability and antibacterial property of PA NF membranes. Full article

(This article belongs to the Special Issue Mixed-Matrix Membranes and Polymeric Membranes 2.0)

► Show Figures

Figure 1

Journal Menu

Journal Browser

Editor’s Choice Articles

Further Information

Guidelines

MDPI Initiatives

Follow MDPI