Seismic source

Last updated
An air gun seismic source (30 litre) Air gun hg.jpg
An air gun seismic source (30 litre)

A seismic source is a device that generates controlled seismic energy used to perform both reflection and refraction seismic surveys. A seismic source can be simple, such as dynamite, or it can use more sophisticated technology, such as a specialized air gun. Seismic sources can provide single pulses or continuous sweeps of energy, generating seismic waves, which travel through a medium such as water or layers of rocks. Some of the waves then reflect and refract and are recorded by receivers, such as geophones or hydrophones. [1]

Contents

Seismic sources may be used to investigate shallow subsoil structure, for engineering site characterization, or to study deeper structures, either in the search for petroleum and mineral deposits, or to map subsurface faults or for other scientific investigations. The returning signals from the sources are detected by seismic sensors (geophones or hydrophones) in known locations relative to the position of the source. The recorded signals are then subjected to specialist processing and interpretation to yield comprehensible information about the subsurface. [2]

Source model

A seismic source signal has the following characteristics:

  1. Generates an impulse signal
  2. Band-limited
  3. The generated waves are time-varying

The generalized equation that shows all above properties is:

where is the maximum frequency component of the generated waveform. [3]

Types of sources

Sledgehammer

The most basic seismic source is a sledgehammer. A seismic energy is generated either by striking the ground directly, or more commonly striking a metal or polyethylene plate on the ground. Typically applied for near-surface seismic refraction surveys. Impact of sledgehammer contact with the surface can provide sufficient seismic energy for interface depths up to 30 m or more, depending on geological conditions and physical properties. [4]

Explosives

Explosives most widely used as seismic sources are known as gelatin dynamites. These dynamites are placed into three subcategories, straight gelatins in which nitroglycerin, also known as glyceryl trinitrate with the chemical formula C3H5(ONO2)3 is the active component, ammonia gelatins in which ammonia nitrite with chemical formula NH4NO3 as the active component, and semi gelatins in which the composition consists mostly of nitroglycerin. [5]

Upon detonation, explosives release large volumes of expanding gas very quickly, [6] forcing great pressure to the surroundings in the form of seismic waves.[ citation needed ]

Using explosives as seismic sources has been in practice for decades because of the reliability and energy efficiency they provide. [7] Such sources are most commonly used on land and swampy environments because of high thickness in sediments.[ citation needed ] Typical charge sizes used in the field for reflection surveys are 0.25 kg to 100 kg for single hole sources, 0.25 kg to 250 kg or more for multiple hole sources, and may reach 2500 kg or more for refraction surveys. [5]

Though dynamites and other explosives are efficient seismic sources because of their reduced costs, ease of transport in difficult terrains, and lack of regular maintenance compared to other sources, [8] the use of explosives is becoming restricted in certain areas, causing decline and increasing popularity for alternative seismic sources. [7]

For instance, hexanitrostilbene was the main explosive fill in the thumper mortar round canisters used as part of the Apollo Lunar Active Seismic Experiments. [9] Generally, the explosive charges are placed between 6 and 76 metres (20 and 250 ft) below ground, in a hole that is drilled with dedicated drilling equipment for this purpose. This type of seismic drilling is often referred to as "Shot Hole Drilling". A common drill rig used for "Shot Hole Drilling" is the ARDCO C-1000 drill mounted on an ARDCO K 4X4 buggy. These drill rigs often use water or air to assist the drilling.

Air gun

Litton LP air gun strings using in marine seismic acquisition Litton LP Gun Strings.jpg
Litton LP air gun strings using in marine seismic acquisition
Seismologist with 18 liter air gun array secured for transport aboard the R/V Sikuliaq Seismologist with air gun array.jpg
Seismologist with 18 liter air gun array secured for transport aboard the R/V Sikuliaq

An air gun is used for marine reflection and refraction surveys. It consists of one or more pneumatic chambers that are pressurized with compressed air at pressures from 14 to 21 MPa (2000 to 3000 lbf/in2). Air guns are submerged below the water surface and towed behind a seismic ship. When an air gun is fired, a solenoid is triggered that releases high pressure air from one chamber to the back of a shuttle that is normally held in balance between the two equally pressurised chambers. The instant lowering of air pressure in the first chamber allows the shuttle to move rapidly into the first chamber, releasing a high pressure air reservoir that is behind the shuttle in the second chamber through ports directly into the sea producing a pulse of acoustic energy. [10] Air gun arrays may consist of up to 48 individual air guns with different size chambers or certain air guns volumes may be clustered together. The firing of all of the array is controlled by gun controller and is usually done to within a ± 1 or 2 millisecond tolerance, the aim being to create the optimum initial shock wave followed by the minimum reverberation of the air bubble(s). Since the shuttle is magnetised, the rapid movement into the first chamber on releasing the solenoid value provides a small current that is in effect a timing signal for the firing gun that is returned to the gun controller. A near-field hydrophone located at a known measured distance from the gun port can also be used to time the first break signal into the hydrophone for accurate gun timing verification.

Air gun maintenance is important as guns can misfire; the worst case scenario being an auto-fire where the gun actually fires repeatedly out of synch because of a defect in the gun itself such as a damaged solenoid valve or a leaking gun O-ring. A single auto-firing gun can result in the total array bubble signature becoming corrupted and if undetected, can result in many seismic lines being re-shot just for one auto-firing gun when the fault is found during initial data processing.

During normal handling for deployment and recovery, air guns must never be fully pressurised to their optimum working pressure on deck and it is normal practice to air down guns to 500 psi to prevent water ingress on deployment and recovery. It is also a poor and dangerous practice to test fire guns on deck in the air at pressure. There must also be an isolation system in place to prevent the accidental firing of guns on deck by observers or navigators by mistake. High pressure air releases on deck can amputate fingers and also result in a high pressure injection injury through the skin, an almost untreatable and deadly injury in a seismic environment. Gunners should wear the required personal protective equipment to protect their eyes and their hearing and minimise exposure of uncovered skin.

Air guns are made from the highest grades of corrosion resistant stainless steel. Large chambers (i.e., greater than 1 L or 70 cu in) tend to give low frequency signals, and the small chambers (less than 1 L) give higher frequency signals.

Plasma sound source

Plasma sound source fired in small swimming pool PSS in swimmingpool 01.jpg
Plasma sound source fired in small swimming pool

A plasma sound source (PSS), otherwise called a spark gap sound source, or simply a sparker, is a means of making a very low frequency sonar pulse underwater. For each firing, electric charge is stored in a large high-voltage bank of capacitors, and then released in an arc across electrodes in the water. The underwater spark discharge produces a high-pressure plasma and vapor bubble, which expands and collapses, making a loud sound. [11] Most of the sound produced is between 20 and 200 Hz, useful for both seismic and sonar applications.

There are also plans to use PSS as a non-lethal weapon against submerged divers [ citation needed ].

Thumper truck

Thumper trucks, Noble Energy, northern Nevada 2012. Thumper trucks, Noble Energy.jpg
Thumper trucks, Noble Energy, northern Nevada 2012.

In 1953, the weight dropping thumper technique was introduced as an alternative to dynamite sources.

Vibroseis Vibroseis.jpg
Vibroseis
Vibroseis 2 Vibroseis 2.jpg
Vibroseis 2
Seismic vibrator during operation

A thumper truck (or weight-drop) truck is a vehicle-mounted ground impact system that can be used to provide a seismic source. A heavy weight is raised by a hoist at the back of the truck and dropped, generally about three meters, to impact (or "thump") the ground. [12] To augment the signal, the weight may be dropped more than once at the same spot, the signal may also be increased by thumping at several nearby places in an array whose dimensions may be chosen to enhance the seismic signal by spatial filtering.

More advanced thumpers use a technology called "Accelerated Weight Drop" (AWD), where a high pressure gas (min 7 MPa (1000 lbf/in2)) is used to accelerate a heavy weight hammer (5,000 kg (11,000 lb)) to hit a base plate coupled to the ground from a distance of 2 to 3 metres (6 ft 7 in to 9 ft 10 in). Several thumps are stacked to enhance signal to noise ratio. AWD allows both more energy and more control of the source than gravitational weight-drop, providing better depth penetration, control of signal frequency content.

Thumping may be less damaging to the environment than firing explosives in shot-holes, [13] [ citation needed ] though a heavily thumped seismic line with transverse ridges every few meters might create long-lasting disturbance of the soil. An advantage of the thumper (later shared with Vibroseis), especially in politically unstable areas, is that no explosives are required.

Electromagnetic Pulse Energy Source (Non-Explosive)

EMP sources based on the electrodynamic and electromagnetic principles.

Seismic vibrator

A seismic vibrator propagates energy signals into the Earth over an extended period of time as opposed to the near instantaneous energy provided by impulsive sources. The data recorded in this way must be correlated to convert the extended source signal into an impulse. The source signal using this method was originally generated by a servo-controlled hydraulic vibrator or shaker unit mounted on a mobile base unit, but electro-mechanical versions have also been developed.

The "Vibroseis" exploration technique was developed by the Continental Oil Company (Conoco) during the 1950s and was a trademark until the company's patent lapsed.

Boomer sources

Boomer sound sources are used for shallow water seismic surveys, mostly for engineering survey applications. Boomers are towed in a floating sled behind a survey vessel. Similar to the plasma source, a boomer source stores energy in capacitors, but it discharges through a flat spiral coil instead of generating a spark. A copper plate adjacent to the coil flexes away from the coil as the capacitors are discharged. This flexing is transmitted into the water as the seismic pulse. [14]

Originally the storage capacitors were placed in a steel container (the bang box) on the survey vessel. The high voltages used, typically 3,000 V, required heavy cables and strong safety containers. Recently, low voltage boomers have become available. [15] These use capacitors on the towed sled, allowing efficient energy recovery, lower voltage power supplies and lighter cables. The low voltage systems are generally easier to deploy and have fewer safety concerns.

Noise sources

Correlation-based processing techniques also enable seismologists to image the interior of the Earth at multiple scales using natural (e.g., the oceanic microseism) or artificial (e.g., urban) background noise as a seismic source. [16] For example, under ideal conditions of uniform seismic illumination, the correlation of the noise signals between two seismographs provides an estimate of the bidirectional seismic impulse response.

See also

Related Research Articles

<span class="mw-page-title-main">Geophysics</span> Physics of the Earth and its vicinity

Geophysics is a subject of natural science concerned with the physical processes and physical properties of the Earth and its surrounding space environment, and the use of quantitative methods for their analysis. Geophysicists, who usually study geophysics, physics, or one of the Earth sciences at the graduate level, complete investigations across a wide range of scientific disciplines. The term geophysics classically refers to solid earth applications: Earth's shape; its gravitational, magnetic fields, and electromagnetic fields ; its internal structure and composition; its dynamics and their surface expression in plate tectonics, the generation of magmas, volcanism and rock formation. However, modern geophysics organizations and pure scientists use a broader definition that includes the water cycle including snow and ice; fluid dynamics of the oceans and the atmosphere; electricity and magnetism in the ionosphere and magnetosphere and solar-terrestrial physics; and analogous problems associated with the Moon and other planets.

<span class="mw-page-title-main">Microphone</span> Device that converts sound into an electrical signal

A microphone, colloquially called a mic, or mike, is a transducer that converts sound into an electrical signal. Microphones are used in many applications such as telephones, hearing aids, public address systems for concert halls and public events, motion picture production, live and recorded audio engineering, sound recording, two-way radios, megaphones, and radio and television broadcasting. They are also used in computers and other electronic devices, such as mobile phones, for recording sounds, speech recognition, VoIP, and other purposes, such as ultrasonic sensors or knock sensors.

<span class="mw-page-title-main">Seismic wave</span> Seismic, volcanic, or explosive energy that travels through Earths layers

A seismic wave is a mechanical wave of acoustic energy that travels through the Earth or another planetary body. It can result from an earthquake, volcanic eruption, magma movement, a large landslide and a large man-made explosion that produces low-frequency acoustic energy. Seismic waves are studied by seismologists, who record the waves using seismometers, hydrophones, or accelerometers. Seismic waves are distinguished from seismic noise, which is persistent low-amplitude vibration arising from a variety of natural and anthropogenic sources.

In petroleum exploration and development, formation evaluation is used to determine the ability of a borehole to produce petroleum. Essentially, it is the process of "recognizing a commercial well when you drill one".

A transducer is a device that converts energy from one form to another. Usually a transducer converts a signal in one form of energy to a signal in another. Transducers are often employed at the boundaries of automation, measurement, and control systems, where electrical signals are converted to and from other physical quantities. The process of converting one form of energy to another is known as transduction.

<span class="mw-page-title-main">Impedance matching</span> Adjusting input/output impedances of an electrical circuit for some purpose

In electrical engineering, impedance matching is the practice of designing or adjusting the input impedance or output impedance of an electrical device for a desired value. Often, the desired value is selected to maximize power transfer or minimize signal reflection. For example, impedance matching typically is used to improve power transfer from a radio transmitter via the interconnecting transmission line to the antenna. Signals on a transmission line will be transmitted without reflections if the transmission line is terminated with a matching impedance.

<span class="mw-page-title-main">Reflection seismology</span> Explore subsurface properties with seismology

Reflection seismology is a method of exploration geophysics that uses the principles of seismology to estimate the properties of the Earth's subsurface from reflected seismic waves. The method requires a controlled seismic source of energy, such as dynamite or Tovex blast, a specialized air gun or a seismic vibrator. Reflection seismology is similar to sonar and echolocation.

<span class="mw-page-title-main">Seismic refraction</span> Geophysical principle

Seismic refraction is a geophysical principle governed by Snell's Law of refraction. The seismic refraction method utilizes the refraction of seismic waves by rock or soil layers to characterize the subsurface geologic conditions and geologic structure.

A geophone is a device that converts ground movement (velocity) into voltage, which may be recorded at a recording station. The deviation of this measured voltage from the base line is called the seismic response and is analyzed for structure of the Earth.

<span class="mw-page-title-main">Vertical seismic profile</span> Vibration measurement using boreholes

In geophysics, vertical seismic profile (VSP) is a technique of seismic measurements used for correlation with surface seismic data. The defining characteristic of a VSP is that either the energy source, or the detectors are in a borehole. In the most common type of VSP, hydrophones, or more often geophones or accelerometers, in the borehole record reflected seismic energy originating from a seismic source at the surface.

A drilling rig is used to create a borehole or well in the earth's sub-surface, for example in order to extract natural resources such as gas or oil. During such drilling, data is acquired from the drilling rig sensors for a range of purposes such as: decision-support to monitor and manage the smooth operation of drilling; to make detailed records of the geologic formations penetrated by a borehole; to generate operations statistics and performance benchmarks such that improvements can be identified, and to provide well planners with accurate historical operations-performance data with which to perform statistical risk analysis for future well operations. The terms measurement while drilling (MWD), and logging while drilling (LWD) are not used consistently throughout the industry. Although these terms are related, within the context of this section, the term measurement while drilling refers to directional-drilling measurements, e.g. for decision support for the wellbore path, while LWD refers to measurements concerning the geological formations penetrated while drilling.

<span class="mw-page-title-main">Underwater explosion</span> Chemical or nuclear explosion that occurs underwater

An underwater explosion is a chemical or nuclear explosion that occurs under the surface of a body of water. While useful in anti-ship and submarine warfare, underwater bombs are not as effective against coastal facilities.

<span class="mw-page-title-main">Geophysical imaging</span>

Geophysical imaging is a minimally destructive geophysical technique that investigates the subsurface of a terrestrial planet. Geophysical imaging is a noninvasive imaging technique with a high parametrical and spatio-temporal resolution. It can be used to model a surface or object understudy in 2D or 3D as well as monitor changes.

Sonic logging is a well logging tool that provides a formation’s interval transit time, designated as , which is a measure of a how fast elastic seismic compressional and shear waves travel through the formations. Geologically, this capacity varies with many things including lithology and rock textures, most notably decreasing with an increasing effective porosity and increasing with an increasing effective confining stress. This means that a sonic log can be used to calculate the porosity, confining stress, or pore pressure of a formation if the seismic velocity of the rock matrix, , and pore fluid, , are known, which is very useful for hydrocarbon exploration.

<span class="mw-page-title-main">Seismic vibrator</span>

A seismic vibrator is a truck-mounted or buggy-mounted device that is capable of injecting low-frequency vibrations into the earth. It is one of a number of seismic sources used in reflection seismology. The ‘Vibroseis’ exploration technique was developed by the Continental Oil Company (Conoco) during the 1950s and was a trademark until the company's patent lapsed.

<span class="mw-page-title-main">Explosion</span> Sudden release of heat and gas

An explosion is a rapid expansion in volume of a given amount of matter associated with an extreme outward release of energy, usually with the generation of high temperatures and release of high-pressure gases. Explosions may also be generated by a slower expansion that would normally not be forceful, but is not allowed to expand, so that when whatever is containing the expansion is broken by the pressure that builds as the matter inside tries to expand, the matter expands forcefully. An example of this is a volcanic eruption created by the expansion of magma in a magma chamber as it rises to the surface. Supersonic explosions created by high explosives are known as detonations and travel through shock waves. Subsonic explosions are created by low explosives through a slower combustion process known as deflagration.

<span class="mw-page-title-main">Applications of capacitors</span> Uses of capacitors in daily life

Capacitors have many uses in electronic and electrical systems. They are so ubiquitous that it is rare that an electrical product does not include at least one for some purpose. Capacitors allow only AC signals to pass when they are charged blocking DC signals. The main components of filters are capacitors. Capacitors have the ability to connect one circuit segment to another. Capacitors are used by Dynamic Random Access Memory (DRAM) devices to represent binary information as bits.

<span class="mw-page-title-main">Surface wave inversion</span>

Seismic inversion involves the set of methods which seismologists use to infer properties through physical measurements. Surface-wave inversion is the method by which elastic properties, density, and thickness of layers in the subsurface are obtained through analysis of surface-wave dispersion. The entire inversion process requires the gathering of seismic data, the creation of dispersion curves, and finally the inference of subsurface properties.

<span class="mw-page-title-main">Active Seismic Experiment</span> Geophysical experiment carried out at the Moon surface by Apollo missions

Active Seismic Experiment (ASE) was carried on Apollo 14 and Apollo 16 as part of the Apollo Lunar Surface Experiments Package (ALSEP). ASE used a thumper device and a mortar with explosive charges to explore subsurface lunar structure and elastic properties. The experiment's principal investigator was Robert Kovach of Stanford University. The experiment was succeeded on Apollo 17 by the Lunar Seismic Profiling experiment.

<span class="mw-page-title-main">Seismic data acquisition</span> Stage of seismic exploration

Seismic data acquisition is the first of the three distinct stages of seismic exploration, the other two being seismic data processing and seismic interpretation. Seismic acquisition requires the use of a seismic source at specified locations for a seismic survey, and the energy that travels within the subsurface as seismic waves generated by the source gets recorded at specified locations on the surface by what is known as receivers.

References

  1. R.E. Sheriff (2002) p160 & p 182
  2. R.E. Sheriff (2002) p312
  3. Seismic Wave Propagation Modeling and Inversion, Phil Bording Archived 2008-02-08 at the Wayback Machine
  4. Reynolds, John M. (2011). An introduction to applied and environmental geophysics (2nd ed.). Chichester, West Sussex: Wiley-Blackwell. pp. 155–156. ISBN   978-0-471-48535-3.
  5. 1 2 Stark, Andreas (2010). Seismic Methods and Applications. Universal-Publishers. pp. 177–178. ISBN   9781599424439.
  6. "Explosive | chemical product". Encyclopedia Britannica. Retrieved 2018-10-09.
  7. 1 2 Yordkayhun, Sawasdee; Ivanova, Alexandra; Giese, Rüdiger; Juhlin, Christopher; Cosma, Calin (January 2009). "Comparison of surface seismic sources at the CO2SINK site, Ketzin, Germany". Geophysical Prospecting. 57 (1): 125–139. Bibcode:2009GeopP..57..125Y. doi:10.1111/j.1365-2478.2008.00737.x. ISSN   0016-8025. S2CID   55497365.
  8. Strobbia, C.; Vermeer, P.; Glushchenko, A.; Laake, A. (2009-06-08). Advances in surface-wave processing for nearsurface characterisation in land seismic. Netherlands: EAGE Publications BV. doi:10.3997/2214-4609.201404894. ISBN   9789462821033.{{cite book}}: |journal= ignored (help)
  9. NASA reference publication
  10. R.E. Sheriff (2002) p6-8
  11. R.E. Sheriff (2002) p328
  12. R.E. Sheriff (2002) p357
  13. Chinenyeze, Madu. "Types of Seismic Energy Sources for Petroleum Exploration in Desert, Dry-Land, Swamp and Marine Environments in Nigeria and Other Sub-Saharan Africa". International Journal of Science and Research (IJSR). 6.
  14. Sheriff R. E., 1991, Encyclopedic Dictionary of Exploration Geophysics, Society of Exploration Geophysicists, Tulsa, 376p
  15. Jopling J. M., Forster P. D., Holland D. C. and Hale R. E., 2004, Low Voltage Seismic Sound Source, US Patent No 6771565
  16. R.E. Sheriff (2002) p295

Bibliography