Lancia Ardea

Last updated
Lancia Ardea
Lancia Ardea.JPG
Overview
Manufacturer Lancia
Production1939–1953
approx 32 000 vehicles
Body and chassis
Class Small family car (C)
Body style
Layout Front-engine, rear-wheel-drive
Powertrain
Engine 903 cc Lancia V4
Max. Power output 26 bhp (19 kW) at 4600 rpm
Transmission 4-speed manual (1939–1948)
5-speed manual (1948–1953) [1]
Dimensions
Wheelbase
  • 2,440 mm (96.1 in)
  • 2,500 mm (98.4 in) (pick-up/van)
  • 2,950 mm (116.1 in) (taxi)
Length3,615 mm (142.3 in)
Width1,380 mm (54.3 in)
Kerb weight 780 kg (1,720 lb) (saloon)
Chronology
Predecessor Lancia Augusta
Successor Lancia Appia

The Lancia Ardea is a small family car produced by Italian car manufacturer Lancia between 1939 and 1953. Its unusually short bonnet reportedly contained the smallest V4 engine ever commercialized in a small family car.

Contents

Nearly 23,000 of the Ardeas produced were standard bodied saloons but between 1940 and 1942 approximately 500 Ardeas were manufactured with lengthened bodies and a squared off rear cabin for use in Rome as taxis. After the war more than 8,500 commercial adaptations of the Ardea known as 'furgoncini' (light van versions) and the 'camioncini' (car based light trucks) were also produced.

The third series Ardea, produced from 1948, was the first mass-produced car with a 5-speed manual transmission. [2] Ardea was named either after Ardea town (Lazio), or Via Ardeatina, Roman road leading from Rome to that town.

The cabin

Instrumentation included a centrally mounted speedometer, the fuel level and the oil pressure. A third dial directly below the driver's sight line was a clock, unusually on this size of car. The three floor pedals followed the pattern still 'conventional' for a manual transmission car (clutch, brake, gas) but to the left of the clutch pedal was a small foot-operated dipper switch for the headlights. Control knobs lined up along the base of the fascia included a hand throttle.

Lancia Ardea MHV Lancia Ardea rear.jpg
Lancia Ardea

Early Italian images of Ardea interiors confirm that Lancias of the period were still right hand drive, a position elsewhere taken to imply driving on the left side of the road. However, right-hand drive is practical even where drivers drive on the right-hand side of the road as it allows a better view of the edge of the road, which is useful when driving on rough roads in mountainous districts. This did mean that drivers of cars with centrally located floor mounted gear shifts, such as the Ardea, needed to learn how to shift with the left hand. During the 1920s Italian leader Benito Mussolini required all Italian drivers to drive on the right, but Lancia would continue, through the 1950s, to supply right hand drive cars in areas viewed by other automakers as left hand drive markets.

History

Four versions of the Ardea were built:

Variants

Alongside the type 250 4-door saloon other body variants of the Ardea were offered.

Chassis

The Ardea was offered as bare chassis (type 350) between 1939–1941 to be bodied by independent coachbuilders. The chassis had the 2440 mm wheelbase of the saloon.

Ardea furgoncino and camioncino

The Aurelia chassis type 550 van (furgoncino, literally "small van") was built in 9 examples already in 1941, but regular production begun only in 1945. [3] The Ardea chassis type 650 pick-up (camioncino, literally "small pickup") was introduced in 1948. [3] In 1949 they were upgraded to fourth series specifications (5-speed gearbox and more powerful 101B engine), and continued to be built until they were superseded by equivalent versions of the Appia in 1954. Unlike on the earlier Augusta, whose commercial variants were bodied by third-party coachbuilders, these Ardeas were factory-built by Lancia. [3]

Tassì Roma

The Tassì Roma, chassis type 450, was an Ardea derivative with special 6-window saloon body, intended for use as a taxicab. It paired the Ardea's running gear with a larger chassis (longer 2,950 mm or 116.1 in wheelbase and wider tracks) which allowed for better passenger accommodation. From 1939 to 1941 about 500 were made—501 or 511 depending on the source. [3]

Related Research Articles

<span class="mw-page-title-main">Lancia Thema</span> Motor vehicle

The Lancia Thema is an executive car produced by the Italian automaker Lancia between 1984 and 1994, and one of four cars to share the Type Four platform alongside the Alfa Romeo 164, Fiat Croma and Saab 9000. The Thema was first shown in Turin Motor Show in 1984.

<span class="mw-page-title-main">Lancia Aurelia</span> 1950s-era car

The Lancia Aurelia is a car produced by Italian manufacturer Lancia from 1950 to the summer of 1958. It is noted for using one of the first series-production V6 engines. Several body styles were offered: 4-door saloon, 2-door GT coupé (B20), 2-door spider/convertible (B24), and a chassis to be custom bodied by external coachbuilders.

<span class="mw-page-title-main">Lancia Fulvia</span> Motor vehicle

The Lancia Fulvia is a car produced by Lancia between 1963 and 1976. Named after Via Fulvia, the Roman road leading from Tortona to Turin, it was introduced at the Geneva Motor Show in 1963 and manufactured in three variants: Berlina 4-door saloon, 2-door Coupé, and Sport, an alternative fastback coupé designed and built by Zagato on the Coupé floorpan.

<span class="mw-page-title-main">Lancia Beta</span> Italian car produced 1972 to 1984

The Lancia Beta, stylised as Lancia β, was an entry-level luxury car produced by Italian car manufacturer Lancia from 1972 to 1984. It was the first new model introduced by Lancia after it had been taken over by Fiat in 1969.

<span class="mw-page-title-main">Rolls-Royce Silver Dawn</span> Motor vehicle

The Rolls-Royce Silver Dawn is a full-size luxury car that was produced by Rolls-Royce at their Crewe works between 1949 and 1955. It was the first Rolls-Royce car to be offered with a factory built body which it shared, along with its chassis, with the Bentley Mark VI until 1952 and then the Bentley R Type until production finished in 1955. The car was first introduced as an export only model. The left hand drive manual transmission models had a column gear change, while right hand drives had a floor change by the door. In the British home market the Silver Dawn only became available from October 1953, with the introduction of the model corresponding to the Bentley R Type.

<span class="mw-page-title-main">Bentley Mark VI</span> Motor vehicle

The Bentley Mark VI is an automobile from Bentley which was produced from 1946 until 1952.

<span class="mw-page-title-main">Bentley R Type</span> Motor vehicle

The Bentley R Type is the second series of post-war Bentley automobiles, produced from 1952 to 1955 as the successor the Mark VI. Essentially a larger-boot version of the Mk VI, the R type is regarded by some as a stop-gap before the introduction of the S series cars in 1955. As with its predecessor, a standard body was available as well as coachbuilt versions by firms including H. J. Mulliner & Co., Park Ward, Harold Radford, Freestone and Webb, Carrosserie Worblaufen and others.

<span class="mw-page-title-main">Rolls-Royce Phantom II</span> Ultra-luxury flagship automobile in its second generation

The Rolls-Royce Phantom II was the third and last of Rolls-Royce's 40/50 hp models, replacing the New Phantom in 1929. It used an improved version of the New Phantom engine in an all-new chassis. A "Continental" version, with a short wheelbase and stiffer springs, was offered.

<span class="mw-page-title-main">Rolls-Royce Phantom III</span> Ultra-luxury flagship automobile in its third generation

The Rolls-Royce Phantom III was the final large pre-war Rolls-Royce. Introduced in 1936, it replaced the Phantom II and it was the only V12 Rolls-Royce until the 1998 introduction of the Silver Seraph. It is the first of the three V12-powered Rolls-Royce Phantoms, with the 2003-2017 Rolls-Royce Phantom VII and 2018- Rolls-Royce Phantom VIII being the other two. 727 V12 Phantom III chassis were constructed from 1936 to 1939, and approximately 650 have survived. Although chassis production ceased in 1939, cars were still being bodied and delivered in 1940 and 1941. The last car, though the rolling chassis was completed in 1941, was not delivered with a body to its owner until 1947. The Phantom III was the last car that Henry Royce worked on – he died, aged 70, a year into the Phantom III's development.

<span class="mw-page-title-main">Lancia Flaminia</span> Motor vehicle

The Lancia Flaminia is a luxury car produced by Italian automaker Lancia from 1957 until 1970. It was Lancia's flagship model at that time, replacing the Aurelia. It was available throughout its lifetime as saloon, coupé and cabriolet. The Flaminia coupé and cabriolet were coachbuilt cars with bodies from several prestigious Italian coachbuilders. Four "presidential" stretched limousine Flaminias were produced by Pininfarina for use on state occasions.

<span class="mw-page-title-main">Rolls-Royce 20/25</span> Motor vehicle

The Rolls-Royce 20/25 is the second of Rolls-Royce Limited's inter-war entry-level models. Built between 1929 and 1936, it was very popular, becoming the most successful selling inter-war Rolls-Royce. Its success enabled Rolls-Royce to survive the Great Depression, and remain one of World's great brands. 3,827 20/25s were produced, and more than 70% of these survive in use.

<span class="mw-page-title-main">Lancia Appia</span> Motor vehicle

The Lancia Appia is a passenger car introduced in 1953 by Italian car manufacturer Lancia as a replacement for the Ardea, and which remained in production for ten years. The Appia was the last in a long line of Lancia production cars dating back to the Lancia Lambda to use sliding pillar front suspension. All three series produced had a 1089cc Lancia V4 engine.

<span class="mw-page-title-main">Rover 10</span> Motor vehicle

The Rover 10 was a small family car from the British Rover car company produced between 1927 and 1947.

<span class="mw-page-title-main">Alfa Romeo 6C</span> Motor vehicle

The Alfa Romeo 6C name was used on road, race, and sports cars produced between 1927 and 1954 by Alfa Romeo; the "6C" name refers to the six cylinders of the car's straight-six engine. Bodies for these cars were made by coachbuilders such as James Young, Zagato, Touring Superleggera, Castagna, and Pinin Farina. Beginning in 1933 there was also a 6C version with an Alfa factory body, built in Portello. In the early 1920s Vittorio Jano received a commission to create a lightweight, high performance vehicle to replace the Giuseppe Merosi designed RL and RM models. The car was introduced in April 1925 at the Salone dell' Automobile di Milano as the 6C 1500. It was based on Alfa's P2 Grand Prix car, using a single overhead cam 1,487 cc in-line six-cylinder engine, producing 44 horsepower. In 1928 the 1500 Sport was presented, which was the first Alfa Romeo road car with double overhead camshafts.

<span class="mw-page-title-main">Lancia Artena</span> Motor vehicle

The Lancia Artena is a passenger car produced by Italian car manufacturer Lancia from 1931 until 1936, and from 1940 until 1942 chiefly for army and government use. It was powered by a 2-litre Lancia V4 engine, while chassis and factory bodies were shared with the more luxurious 2.6-litre V8-engined Lancia Astura. Total production amounted to 5,567 examples.

<span class="mw-page-title-main">Lancia Epsilon</span> Motor vehicle

The Lancia 20/30 HP, later known as Lancia Epsilon, is a passenger car produced by Italian car manufacturer Lancia between 1911 and 1912. The car was quite similar to the previous 20/30 HP Delta model. In total 357 were made.

<span class="mw-page-title-main">Rover 12</span> Name given to several medium-sized family cars from the British Rover car company

The Rover 12 was a name given to several medium-sized family cars from the British Rover car company between 1905 and 1948.

<span class="mw-page-title-main">Humber Snipe</span> Motor vehicle

The Humber Snipe was a four-door luxury saloon introduced by British-based Humber Limited for 1930 as a successor to the Humber 20/55 hp at the same time as the similar but slightly longer Humber Pullman.

The Lancia Ro, Lancia Ro-Ro and Lancia 3Ro were 4x2 heavy trucks built by Italian manufacturer Lancia from the 1930s through the 1940s for military and civilian use. The 2-cylinder diesel Ro was produced from 1933 to 1939, the 3-cylinder diesel Ro-Ro from 1935 to 1939 and the improved 5-cylinder diesel 3Ro from 1938 to 1947.

<span class="mw-page-title-main">Lancia Jota</span> Motor vehicle

The Lancia Jota is a series of truck and bus chassis produced by Lancia between 1915 and 1935. The original 1915 Jota was the first true Lancia truck; throughout the following two decades it was made in a number of different series and variants, each identified by a progressive Greek numeral prefix added to the name, from Djota to the last Eptajota. While axle tracks, wheelbase and equipment gradually grew, the original layout and 4,940 cc four-cylinder petrol engine were retained.

References

  1. 1 2 "Lancia Ardea". carsfromitaly.net. Retrieved 2007-11-26.
  2. "Innovation by Lancia, performance by Abarth". classicaldrives.com. Archived from the original on 2010-11-22. Retrieved 2007-11-26.
  3. 1 2 3 4 Amatori 1992.

Bibliography