Carbon dioxide flooding

Last updated

Carbon dioxide (CO2) flooding is a process in which carbon dioxide is injected into an oil reservoir to increase the output when extracting oil. This is most often used in reservoirs where production rates have declined due to depletion.

Contents

Overview

Figure 1. Carbon dioxide pressure-temperature phase diagram Carbon dioxide pressure-temperature phase diagram.jpg
Figure 1. Carbon dioxide pressure-temperature phase diagram

When the amount of recoverable oil in an oil reservoir is depleted through primary and secondary production, around 60 to 70% of oil that was originally in the reservoir may still remain. [1] In some cases, carbon dioxide (CO2) flooding may be an ideal tertiary recovery method to recover more of the recoverable oil than could be produced using secondary oil recovery methods.

Because of its special properties, CO2 improves oil recovery by lowering interfacial tension, swelling the oil, reducing viscosity of the oil, and by mobilizing the lighter components of the oil. [2] When the injected CO2 and residual oil are miscible, the physical forces holding the two fluids apart effectively disappears. This results in a viscosity reduction of the hydrocarbon and makes it easier to displace the crude oil from the rock pores and sweep it to the production well. [3]

In other cases where the CO2 and residual oil are immiscible, the injected CO2 may still be used to drive the crude oil through the formation to be produced. [4] One reason this occurs is because the injected CO2 can flow into the minute pores that are unavailable to oil and water. [5]

Process

As an oil field matures and production rates decline, there is a growing incentive to intervene and attempt to increase oil output utilizing tertiary recovery techniques (also termed improved or enhanced oil recovery). Petroleum engineers assess available options for increasing reservoir productivity. The options include chemical flooding, thermal/steam injection, and CO2 injection. [2] [6]

One of the criteria for determining if CO2 flooding is a candidate for the recovery of oil from the formation is the pressure of the formation. The miscibility of the CO2 and the crude oil is dependent upon the pressure and the temperature. However, since it is difficult to change the temperature of the reservoir, the pressure of the reservoir may be adjusted, to an extent, to bring the reservoir to a pressure that keeps the CO2 in a supercritical state. If a miscible flood is found to be feasible, the pressure is kept above the minimum miscibility pressure (MMP). [3] [2] The pressure may be below the MMP if an immiscible flood is desired.

Inverted 5-spot Pattern Inverted 5-spot Pattern.png
Inverted 5-spot Pattern

A petroleum engineer will then determine a method of using CO2 flooding to recover petroleum from the reservoir. This may be a continuous injection method, a water alternating gas (WAG) method, or some combination. [2] The amount, or amounts of CO2 will be determined by the amount of the pore volume of the formation that is filled with oil. This is known as the hydrocarbon pore volume (HCPV). [3] The petroleum engineer will also decide if the flood will be a pattern flood or a line drive flood. [2] [6] In a pattern flood, CO2 is usually injected into a number of injection wells surrounding a producing well. Alternatively, CO2 may be injected into injector wells surrounded by producing wells. This is called an inverted pattern. In a line drive, the injection wells are located in a straight line parallel to the production wells. [7]

Optimally, a slug of CO2 will mobilize a flood front where the mixture of oil and CO2 will mobilize more oil. [7] [2] This flood front will radiate from each injection well towards the surrounding producing wells where the oil will be produced. The formation of a front is dependent upon the rate that the CO2 is injected, how fast it mobilizes the oil, and the porosity of the formation. [7] Injecting the CO2 too fast will allow the CO2 to channel from the injector directly to a producing well without mobilizing any oil. Injecting CO2 too quickly may fracture the formation, which may again allow channeling from the injector to any or all of the producing wells. [2] [6] [8] Also, injecting CO2 may migrate fines, which are small particles of clay and minerals, may plug the pores and prevent the mobilization of oil through the formation. [9]

In a continuous flood, a slug of CO2 will be continuously injected and not followed by any other fluid. The amount of CO2 is usually calculated to be around 100% of the HCPV of the field or pattern. In a water alternating gas (WAG) process, slugs of CO2 are followed by slugs of water. The overall amount of CO2 may be between 40% and 50% of the HCPV. [2] [6] [8] The WAG process is known to reduce channeling of the CO2. [6]

Formations and Oil

Drilling rigs in the Permian Basin, where much of the CO2 flooding occurs in the United States. OdessaPermian.jpg
Drilling rigs in the Permian Basin, where much of the CO2 flooding occurs in the United States.

Sandstone and carbonate reservoirs (such as limestone or dolomite) are preferred for this method over reservoirs with ultra-low permeability such as shale due to the risk of CO2 channeling through hydraulic or natural fractures in the rock. [2] [1] CO2 flooding is still sometimes used in these instances, but usually using the "huff and puff" CO2 injection method, which allows the CO2 to soak in a reservoir after being pumped in through the injection well for a period of time before the production well is opened and put back into functionality. [10] [6] This method reduces the chances of unwanted channeling, and increases the amounts of oil that may be recovered as opposed to the more common CO2 injection water alternating gas process (WAG) or by following a soak of CO2 with steam. [1] [11]

Miscible CO2 flooding is a method preferred for medium to light oils due to the mobility ratio between the CO2 and the oil. [7] The mobility ratio refers to the ratio of the mobility of the CO2 fluid injected into a reservoir for secondary or tertiary production versus the mobility of the oil. [1] [2] [8] For medium or light oils with a high API gravity, fluids or gases that are less viscous themselves can be used. However, if an injection fluid or gas that had lower viscosity was used on a heavy crude oil or bitumen, the injection fluid or gas would bypass the oil and result in a poorly swept reservoir. [1]

In cases where the reservoir is filled with extremely heavy oil or bitumen, steam injection, or other methods that employ heat, are much more commonly favored so that the mobility or viscosity of the oil can be lowered and the extraction will become easier. [1] Generally, reservoirs with lighter oils will have higher recovery percentages with primary and secondary recovery methods, but reservoirs with heavier oils or bitumen will have much lower recovery with primary and secondary recovery methods and the transition from secondary to tertiary methods will have to occur much earlier in the reservoir's lifespan.

History

Using CO2 for enhanced oil recovery was first investigated and patented in 1952. [12] In 1964, a field test was conducted at the Mead Strawn Field, which involved the injection of a large slug of CO2 (25% of the hydrocarbon pore volume or HCPV) followed by carbonated water at reservoir conditions. Results indicated that 53 to 82 percent more oil was produced by the CO2 flood than was produced by water in the best areas of the waterflood. [13]

The process was first commercially attempted in 1977 in Scurry County, Texas. [13] Since then, the process has become extensively used in the Permian basin region of the US and is now more recently is being pursued in many different states. [1] It is now being more actively pursued in China and throughout the rest of the world. [2] [14] [15]

Sequestration of Carbon Dioxide

In connection with greenhouse gas emissions and global warming, CO2 flooding may be used to sequester CO2 underground and therefore offset CO2 emissions elsewhere. [16]

See also

Related Research Articles

<span class="mw-page-title-main">Oil well</span> Well drilled to extract crude oil and/or gas

An oil well is a drillhole boring in Earth that is designed to bring petroleum oil hydrocarbons to the surface. Usually some natural gas is released as associated petroleum gas along with the oil. A well that is designed to produce only gas may be termed a gas well. Wells are created by drilling down into an oil or gas reserve that is then mounted with an extraction device such as a pumpjack which allows extraction from the reserve. Creating the wells can be an expensive process, costing at least hundreds of thousands of dollars, and costing much more when in hard to reach areas, e.g., when creating offshore oil platforms. The process of modern drilling for wells first started in the 19th century, but was made more efficient with advances to oil drilling rigs during the 20th century.

Gas reinjection is the reinjection of natural gas into an underground reservoir, typically one already containing both natural gas and crude oil, in order to increase the pressure within the reservoir and thus induce the flow of crude oil or else sequester gas that cannot be exported. This is not to be confused with gas lift, where gas is injected into the annulus of the well rather than the reservoir. After the crude has been pumped out, the natural gas is once again recovered. Since many of the wells found around the world contain heavy crude, this process increases their production. The basic difference between light crude and heavy crude is its viscosity and pumpability—the lighter the crude the easier it is to pump. Recovery of hydrocarbons in a well is generally limited to 50% and 75–80%. Recycling of natural gas or other inert gases causes the pressure to rise in the well, thus causing more gas molecules to dissolve in the oil lowering its viscosity and thereby increasing the well's output. Air is not suitable for repressuring wells because it tends to cause deterioration of the oil, thus carbon dioxide or natural gas is used to repressure the well. The term 'gas-reinjection' is also sometimes referred to as repressuring—the term being used only to imply that the pressure inside the well is being increased to aid recovery.

<span class="mw-page-title-main">Petroleum reservoir</span> Subsurface pool of hydrocarbons

A petroleum reservoir or oil and gas reservoir is a subsurface accumulation of hydrocarbons contained in porous or fractured rock formations.

<span class="mw-page-title-main">Supercritical carbon dioxide</span> Carbon dioxide above its critical point

Supercritical carbon dioxide is a fluid state of carbon dioxide where it is held at or above its critical temperature and critical pressure.

Residual oil is oil found in low concentrations naturally or in exhausted oil fields. Often mixed with water, it cannot be recovered by conventional techniques. However, part of it can be recovered using carbon dioxide-enhanced oil recovery which involves injecting carbon dioxide into the well reducing viscosity and enhancing flow of the oil. The technique is not new but has not been used extensively on residual oil zones, low-grade deposits of petroleum such as the 40 square miles in the Permian Basin of Texas leased by Tiny Kamalabo. The technique is limited by availability of carbon dioxide. Carbon dioxide is injected and recycled as many times as possible, and stored in the depleted reservoir at the end of the life for the field. United States reserves of residual oil are estimated to be 100 billion barrels.

Enhanced oil recovery, also called tertiary recovery, is the extraction of crude oil from an oil field that cannot be extracted otherwise. Although the primary and secondary recovery techniques rely on the pressure differential between the surface and the underground well, enhanced oil recovery functions by altering the chemical composition of the oil itself in order to make it easier to extract. EOR can extract 30% to 60% or more of a reservoir's oil, compared to 20% to 40% using primary and secondary recovery. According to the US Department of Energy, carbon dioxide and water are injected along with one of three EOR techniques: thermal injection, gas injection, and chemical injection. More advanced, speculative EOR techniques are sometimes called quaternary recovery.

Steam-assisted gravity drainage is an enhanced oil recovery technology for producing heavy crude oil and bitumen. It is an advanced form of steam stimulation in which a pair of horizontal wells is drilled into the oil reservoir, one a few metres above the other. High pressure steam is continuously injected into the upper wellbore to heat the oil and reduce its viscosity, causing the heated oil to drain into the lower wellbore, where it is pumped out. Dr. Roger Butler, engineer at Imperial Oil from 1955 to 1982, invented the steam assisted gravity drainage (SAGD) process in the 1970s. Butler "developed the concept of using horizontal pairs of wells and injected steam to develop certain deposits of bitumen considered too deep for mining". In 1983 Butler became director of technical programs for the Alberta Oil Sands Technology and Research Authority (AOSTRA), a crown corporation created by Alberta Premier Lougheed to promote new technologies for oil sands and heavy crude oil production. AOSTRA quickly supported SAGD as a promising innovation in oil sands extraction technology.

Artificial lift refers to the use of artificial means to increase the flow of liquids, such as crude oil or water, from a production well. Generally this is achieved by the use of a mechanical device inside the well or by decreasing the weight of the hydrostatic column by injecting gas into the liquid some distance down the well. A newer method called Continuous Belt Transportation (CBT) uses an oil absorbing belt to extract from marginal and idle wells. Artificial lift is needed in wells when there is insufficient pressure in the reservoir to lift the produced fluids to the surface, but often used in naturally flowing wells to increase the flow rate above what would flow naturally. The produced fluid can be oil, water or a mix of oil and water, typically mixed with some amount of gas.

<span class="mw-page-title-main">Extraction of petroleum</span> Removal of petroleum from the earth

Petroleum is a fossil fuel that can be drawn from beneath the earth's surface. Reservoirs of petroleum are formed through the mixture of plants, algae, and sediments in shallow seas under high pressure. Petroleum is mostly recovered from oil drilling. Seismic surveys and other methods are used to locate oil reservoirs. Oil rigs and oil platforms are used to drill long holes into the earth to create an oil well and extract petroleum. After extraction, oil is refined to make gasoline and other products such as tires and refrigerators. Extraction of petroleum can be dangerous and have led to oil spills.

<span class="mw-page-title-main">Steam injection (oil industry)</span> Method of extracting heavy crude oil

Steam injection is an increasingly common method of extracting heavy crude oil. Used commercially since the 1960s, it is considered an enhanced oil recovery (EOR) method and is the main type of thermal stimulation of oil reservoirs. There are several different forms of the technology, with the two main ones being Cyclic Steam Stimulation and Steam Flooding. Both are most commonly applied to oil reservoirs, which are relatively shallow and which contain crude oils which are very viscous at the temperature of the native underground formation. Steam injection is widely used in the San Joaquin Valley of California (US), the Lake Maracaibo area of Venezuela, and the oil sands of northern Alberta, Canada.

Enhanced coal bed methane recovery is a method of producing additional coalbed methane from a source rock, similar to enhanced oil recovery applied to oil fields. Carbon dioxide (CO2) injected into a bituminous coal bed would occupy pore space and also adsorb onto the carbon in the coal at approximately twice the rate of methane (CH4), allowing for potential enhanced gas recovery. This technique may be used in conjunction with carbon capture and storage in mitigation of global warming where the carbon dioxide that is sequestered is captured from the output of fossil fuel power plants.

Wavefront Technology Solutions Inc. is a provider of secondary oil recovery and environmental technologies. The company was founded in 1997 as PE-TECH by CEO Brett Davidson and University of Alberta professor Tim Spanos. The company was later changed to Wavefront Technologies and Environmental Services. Wavefront Technology Solutions Inc. the company is known for its patented technology that uses pulse technology to simulate the effects of the aftershock of an earthquake to aid in the recovery of stranded oil. These technologies simulate the beating of a heart – when a heart pumps, it sends pulses through the body's blood vessels, causing the network of capillaries to expand and contract. When a pulse is applied to the ground, it expands and contracts the porous rock, essentially freeing the trapped oil. This technology is used for fluid flow optimization having applications in both the environmental and energy sectors. In the environmental sector, the process is marketed as Primawave, while in the energy sector it is marketed as Powerwave.

Heavy oil production is a developing technology for extracting heavy oil in industrial quantities. Estimated reserves of heavy oil are over 6 trillion barrels, three times that of conventional oil and gas.

The Batı Raman oil field (batı meaning west in Turkish) is located in Batman Province, in the Southeastern Anatolia Region of Turkey. With estimated reserves of 1.85 billion barrels (252×106 tonnes) and a production rate of around 7,500 barrels per day (1,190 m3/d) from 300 wells (as of 2007), it is the largest and most productive oil field in Turkey.

The Weyburn-Midale Carbon Dioxide Project is, as of 2008, the world's largest carbon capture and storage project. It is located in Midale, Saskatchewan, Canada.

Solar thermal enhanced oil recovery is a form of thermal enhanced oil recovery (EOR), a technique applied by oil producers to extract more oil from maturing oil fields. Solar EOR uses solar thermal arrays to concentrate the sun's energy to heat water and generate steam. The steam is injected into an oil reservoir to reduce the viscosity, or thin, heavy crude thus facilitating its flow to the surface. Thermal recovery processes, also known as steam injection, have traditionally burned natural gas to produce steam. Solar EOR is proving to be a viable alternative to gas-fired steam production for the oil industry. Solar EOR can generate the same quality steam as natural gas, reaching temperatures up to 750 °F (399 °C) and 2,500 PSI.

<span class="mw-page-title-main">Navitas Land and Mineral Corporation</span> Oil and gas exploration company

Navitas Land and Mineral Corporation is an oil and gas exploration, development and production firm headquartered in Madisonville, Kentucky. Founded in 2009, the company's oil and gas recovery efforts are focused on the Illinois Basin, an area that encompasses Western Kentucky, Southern Illinois, and Southwestern Indiana.

Riyaz Kharrat is an eminent Iranian scientist in the field of chemical engineering and petroleum engineering. He is a full professor at Montanuniversität Leoben.

Microbial Enhanced Oil Recovery (MEOR) is a biological-based technology involving the manipulation of functions or structures within microbial environments present in oil reservoirs. The primary objective of MEOR is to improve the extraction of oil confined within porous media, while boosting economic benefits. As a tertiary oil extraction technology, MEOR enables the partial recovery of the commonly residual 2/3 of oil, effectively prolonging the operational lifespan of mature oil reservoirs.

References

  1. 1 2 3 4 5 6 7 Speight, James G. (2019). "Chapter 2 - Nonthermal Methods of Recovery". Heavy Oil Recovery and Upgrading. Gulf Professional Publishing. pp. 49–112. doi:10.1016/b978-0-12-813025-4.00002-7. ISBN   978-0-12-813025-4.
  2. 1 2 3 4 5 6 7 8 9 10 11 Verma, Mahendra (2015). Fundamentals of carbon dioxide-enhanced oil recovery (CO2-EOR): a supporting document of the assessment methodology for hydrocarbon recovery using CO2-EOR associated with carbon sequestration (Report). Open-File Report. doi: 10.3133/ofr20151071 .
  3. 1 2 3 "Carbon Dioxide Enhanced Oil Recovery" (PDF). U.S. Department of Energy. March 2010.
  4. ↑ Zhang, Na; Wei, Mingzhen; Bai, Baojun (April 2018). Comprehensive Review of Worldwide CO2 Immiscible Flooding. SPE Improved Oil Recovery Conference. Tulsa, Oklahoma, USA.
  5. ↑ Pingping, Shen; Xinglong, Chen; Jishun, Qin (2010). "Pressure characteristics in CO2 flooding experiments". Petroleum Exploration and Development. 37 (2): 211–215. Bibcode:2010PEDO...37..211P. doi: 10.1016/S1876-3804(10)60026-2 .
  6. 1 2 3 4 5 6 Riley, Ronald; Harper, John; Harrison III, William; Barnes, David; Nuttall, Brandon; Avary, Katharine; Wahr, Amanda; Baranoski, Mark; Slater, Brian; Harris, David; Kelley, Stephen. Evaluation of Co2-Enhanced Oil Recovery and Sequestration Opportunities in Oil and Gas Fields in the MRCSP Region (Report). DOE-NETL.
  7. 1 2 3 4 Hughes, Richard (September 2009). Evaluation and Enhancement of Carbon Dioxide Flooding Through Sweep Improvement (Report). doi: 10.2172/983791 . OSTI   983791.
  8. 1 2 3 4 Kuuskraa, Vello A.; Van Leewen, Tyler; Wallace, Matt (June 2011). Improving Domestic Energy Security and Lowering CO2 Emissions with 'Next Generation' CO2-Enhanced Oil Recovery (CO2-EOR) (Report). doi:10.2172/1503260.
  9. ↑ Xie, Quan; Saeedi, Ali; Delle Piane, Claudio; Esteban, Lionel; Brady, Patrick (September 2017). "Fines migration during CO2 injection: Experimental results interpreted using surface forces". International Journal of Greenhouse Gas Control. 65: 32–39. Bibcode:2017IJGGC..65...32X. doi: 10.1016/j.ijggc.2017.08.011 . OSTI   1421635.
  10. ↑ Ahmadi, Mohammad Ali (2018). "Chapter Nine - Enhanced Oil Recovery (EOR) in Shale Oil Reservoirs". In Bahadori, Alireza (ed.). Fundamentals of Enhanced Oil and Gas Recovery from Conventional and Unconventional Reservoirs. Gulf Professional Publishing. pp. 269–290. doi:10.1016/b978-0-12-813027-8.00009-6. ISBN   978-0-12-813027-8.
  11. ↑ US 4,736,792 "Viscous oil recovery method"
  12. ↑ US 2,623,596 "Method for producing oil by means of carbon dioxide"
  13. 1 2 Summary of Carbon Dioxide Enhanced Oil Recovery (CO2EOR) Injection Well Technology (Report). American Petroleum Institute. 2007.
  14. ↑ Hill, Bruce; Li, XiaoChun; Wei, Ning (2020). "CO2-EOR in China: A comparative review". International Journal of Greenhouse Gas Control. 103: 103173. Bibcode:2020IJGGC.10303173H. doi: 10.1016/j.ijggc.2020.103173 . S2CID   228835796.
  15. ↑ Chen, H. Q.; Hu, Y. L.; Tian, C. B. (2012). "Advances in CO2 displacing oil and CO2, sequestrated researches". Oil-Field Chemistry. 29 (1): 116–127.
  16. ↑ Aminu, Mohammed D.; Nabavi, Seyed Ali; Rochelle, Christopher A.; Manovic, Vasilije (2017). "A review of developments in carbon dioxide storage". Applied Energy. 208: 1389–1419. doi:10.1016/j.apenergy.2017.09.015. hdl: 1826/12765 . ISSN   0306-2619.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.