Aquifer

Last updated
Schematic of an aquifer showing confined zones, groundwater travel times, a spring and a well Groundwater flow.svg
Schematic of an aquifer showing confined zones, groundwater travel times, a spring and a well

An aquifer is an underground layer of water-bearing material, consisting of permeable or fractured rock, or of unconsolidated materials (gravel, sand, or silt). Aquifers vary greatly in their characteristics. The study of water flow in aquifers and the characterization of aquifers is called hydrogeology. Related terms include aquitard, which is a bed of low permeability along an aquifer, and aquiclude (or aquifuge), which is a solid, impermeable area underlying or overlying an aquifer, the pressure of which could lead to the formation of a confined aquifer. The classification of aquifers is as follows: Saturated versus unsaturated; aquifers versus aquitards; confined versus unconfined; isotropic versus anisotropic; porous, karst, or fractured; transboundary aquifer.

Contents

Groundwater from aquifers can be sustainably harvested by humans through the use of qanats leading to a well. [1] This groundwater is a major source of fresh water for many regions, however can present a number of challenges such as overdrafting (extracting groundwater beyond the equilibrium yield of the aquifer), groundwater-related subsidence of land, and the salinization or pollution of the groundwater.

Properties

Depth

An aquifer cross-section. This diagram shows two aquifers with one aquitard (a confining or impermeable layer) between them, surrounded by the bedrock aquiclude, which is in contact with a gaining stream (typical in humid regions). The water table and unsaturated zone are also illustrated. Aquifer en.svg
An aquifer cross-section. This diagram shows two aquifers with one aquitard (a confining or impermeable layer) between them, surrounded by the bedrock aquiclude, which is in contact with a gaining stream (typical in humid regions). The water table and unsaturated zone are also illustrated.

Aquifers occur from near-surface to deeper than 9,000 metres (30,000 ft). [2] Those closer to the surface are not only more likely to be used for water supply and irrigation, but are also more likely to be replenished by local rainfall. Although aquifers are sometimes characterized as "underground rivers or lakes," they are actually porous rock saturated with water. [3]

Many desert areas have limestone hills or mountains within them or close to them that can be exploited as groundwater resources. [4] Part of the Atlas Mountains in North Africa, the Lebanon and Anti-Lebanon ranges between Syria and Lebanon, the Jebel Akhdar in Oman, parts of the Sierra Nevada and neighboring ranges in the United States' Southwest, have shallow aquifers that are exploited for their water. Overexploitation can lead to the exceeding of the practical sustained yield; i.e., more water is taken out than can be replenished.

Along the coastlines of certain countries, such as Libya and Israel, increased water usage associated with population growth has caused a lowering of the water table and the subsequent contamination of the groundwater with saltwater from the sea.

In 2013 large freshwater aquifers were discovered under continental shelves off Australia, China, North America and South Africa. They contain an estimated half a million cubic kilometers of "low salinity" water that could be economically processed into potable water. The reserves formed when ocean levels were lower and rainwater made its way into the ground in land areas that were not submerged until the ice age ended 20,000 years ago. The volume is estimated to be 100 times the amount of water extracted from other aquifers since 1900. [5] [6]

Groundwater recharge

This section is an excerpt from Groundwater recharge.[ edit ]
Groundwater recharge or deep drainage or deep percolation is a hydrologic process, where water moves downward from surface water to groundwater. Recharge is the primary method through which water enters an aquifer. This process usually occurs in the vadose zone below plant roots and is often expressed as a flux to the water table surface. Groundwater recharge also encompasses water moving away from the water table farther into the saturated zone. [7] Recharge occurs both naturally (through the water cycle) and through anthropogenic processes (i.e., "artificial groundwater recharge"), where rainwater and/or reclaimed water is routed to the subsurface.

Classification

An aquitard is a zone within the Earth that restricts the flow of groundwater from one aquifer to another. An aquitard can sometimes, if completely impermeable, be called an aquiclude or aquifuge. Aquitards are composed of layers of either clay or non-porous rock with low hydraulic conductivity.

Saturated versus unsaturated

Groundwater can be found at nearly every point in the Earth's shallow subsurface to some degree, although aquifers do not necessarily contain fresh water. The Earth's crust can be divided into two regions: the saturated zone or phreatic zone (e.g., aquifers, aquitards, etc.), where all available spaces are filled with water, and the unsaturated zone (also called the vadose zone), where there are still pockets of air that contain some water, but can be filled with more water.

Saturated means the pressure head of the water is greater than atmospheric pressure (it has a gauge pressure > 0). The definition of the water table is the surface where the pressure head is equal to atmospheric pressure (where gauge pressure = 0).

Unsaturated conditions occur above the water table where the pressure head is negative (absolute pressure can never be negative, but gauge pressure can) and the water that incompletely fills the pores of the aquifer material is under suction. The water content in the unsaturated zone is held in place by surface adhesive forces and it rises above the water table (the zero-gauge-pressure isobar) by capillary action to saturate a small zone above the phreatic surface (the capillary fringe) at less than atmospheric pressure. This is termed tension saturation and is not the same as saturation on a water-content basis. Water content in a capillary fringe decreases with increasing distance from the phreatic surface. The capillary head depends on soil pore size. In sandy soils with larger pores, the head will be less than in clay soils with very small pores. The normal capillary rise in a clayey soil is less than 1.8 m (6 ft) but can range between 0.3 and 10 m (1 and 33 ft). [8]

The capillary rise of water in a small-diameter tube involves the same physical process. The water table is the level to which water will rise in a large-diameter pipe (e.g., a well) that goes down into the aquifer and is open to the atmosphere.

Aquifers versus aquitards

Aquifers are typically saturated regions of the subsurface that produce an economically feasible quantity of water to a well or spring (e.g., sand and gravel or fractured bedrock often make good aquifer materials).

An aquitard is a zone within the Earth that restricts the flow of groundwater from one aquifer to another. [9] A completely impermeable aquitard is called an aquiclude or aquifuge. Aquitards contain layers of either clay or non-porous rock with low hydraulic conductivity.

In mountainous areas (or near rivers in mountainous areas), the main aquifers are typically unconsolidated alluvium, composed of mostly horizontal layers of materials deposited by water processes (rivers and streams), which in cross-section (looking at a two-dimensional slice of the aquifer) appear to be layers of alternating coarse and fine materials. Coarse materials, because of the high energy needed to move them, tend to be found nearer the source (mountain fronts or rivers), whereas the fine-grained material will make it farther from the source (to the flatter parts of the basin or overbank areas—sometimes called the pressure area). Since there are less fine-grained deposits near the source, this is a place where aquifers are often unconfined (sometimes called the forebay area), or in hydraulic communication with the land surface.

Confined versus unconfined

An unconfined aquifer has no impermeable barrier immediately above it, such that the water level can rise in response to recharge. A confined aquifer has an overlying impermeable barrier that prevents the water level in the aquifer from rising any higher. An aquifer in the same geologic unit may be confined in one area and unconfined in another. Unconfined aquifers are sometimes also called water table or phreatic aquifers, because their upper boundary is the water table or phreatic surface (see Biscayne Aquifer). Typically (but not always) the shallowest aquifer at a given location is unconfined, meaning it does not have a confining layer (an aquitard or aquiclude) between it and the surface. The term "perched" refers to ground water accumulating above a low-permeability unit or strata, such as a clay layer. This term is generally used to refer to a small local area of ground water that occurs at an elevation higher than a regionally extensive aquifer. The difference between perched and unconfined aquifers is their size (perched is smaller). Confined aquifers are aquifers that are overlain by a confining layer, often made up of clay. The confining layer might offer some protection from surface contamination.

If the distinction between confined and unconfined is not clear geologically (i.e., if it is not known if a clear confining layer exists, or if the geology is more complex, e.g., a fractured bedrock aquifer), the value of storativity returned from an aquifer test can be used to determine it (although aquifer tests in unconfined aquifers should be interpreted differently than confined ones). Confined aquifers have very low storativity values (much less than 0.01, and as little as 10−5), which means that the aquifer is storing water using the mechanisms of aquifer matrix expansion and the compressibility of water, which typically are both quite small quantities. Unconfined aquifers have storativities (typically called specific yield) greater than 0.01 (1% of bulk volume); they release water from storage by the mechanism of actually draining the pores of the aquifer, releasing relatively large amounts of water (up to the drainable porosity of the aquifer material, or the minimum volumetric water content).

Isotropic versus anisotropic

In isotropic aquifers or aquifer layers the hydraulic conductivity (K) is equal for flow in all directions, while in anisotropic conditions it differs, notably in horizontal (Kh) and vertical (Kv) sense.

Semi-confined aquifers with one or more aquitards work as an anisotropic system, even when the separate layers are isotropic, because the compound Kh and Kv values are different (see hydraulic transmissivity and hydraulic resistance).

When calculating flow to drains [10] or flow to wells [11] in an aquifer, the anisotropy is to be taken into account lest the resulting design of the drainage system may be faulty.

Porous, karst, or fractured

To properly manage an aquifer its properties must be understood. Many properties must be known to predict how an aquifer will respond to rainfall, drought, pumping, and contamination. Considerations include where and how much water enters the groundwater from rainfall and snowmelt, how fast and in what direction the groundwater travels, and how much water leaves the ground as springs. Computer models can be used to test how accurately the understanding of the aquifer properties matches the actual aquifer performance. [12] : 192–193, 233–237  Environmental regulations require sites with potential sources of contamination to demonstrate that the hydrology has been characterized. [12] : 3 

Porous

Water in porous aquifers slowly seeps through pore spaces between sand grains Water seep from sandstone in Hanging Garden SE Utah.jpg
Water in porous aquifers slowly seeps through pore spaces between sand grains

Porous aquifers typically occur in sand and sandstone. Porous aquifer properties depend on the depositional sedimentary environment and later natural cementation of the sand grains. The environment where a sand body was deposited controls the orientation of the sand grains, the horizontal and vertical variations, and the distribution of shale layers. Even thin shale layers are important barriers to groundwater flow. All these factors affect the porosity and permeability of sandy aquifers. [13] : 413 

Sandy deposits formed in shallow marine environments and in windblown sand dune environments have moderate to high permeability while sandy deposits formed in river environments have low to moderate permeability. [13] : 418  Rainfall and snowmelt enter the groundwater where the aquifer is near the surface. Groundwater flow directions can be determined from potentiometric surface maps of water levels in wells and springs. Aquifer tests and well tests can be used with Darcy's law flow equations to determine the ability of a porous aquifer to convey water. [12] : 177–184 

Analyzing this type of information over an area gives an indication how much water can be pumped without overdrafting and how contamination will travel. [12] : 233  In porous aquifers groundwater flows as slow seepage in pores between sand grains. A groundwater flow rate of 1 foot per day (0.3 m/d) is considered to be a high rate for porous aquifers, [14] as illustrated by the water slowly seeping from sandstone in the accompanying image to the left.

Porosity is important, but, alone, it does not determine a rock's ability to act as an aquifer. Areas of the Deccan Traps (a basaltic lava) in west central India are good examples of rock formations with high porosity but low permeability, which makes them poor aquifers. Similarly, the micro-porous (Upper Cretaceous) Chalk Group of south east England, although having a reasonably high porosity, has a low grain-to-grain permeability, with its good water-yielding characteristics mostly due to micro-fracturing and fissuring.

Karst

Water in karst aquifers can form subterranean rivers. MammothCaveNPS.jpg
Water in karst aquifers can form subterranean rivers.

Karst aquifers typically develop in limestone. Surface water containing natural carbonic acid moves down into small fissures in limestone. This carbonic acid gradually dissolves limestone thereby enlarging the fissures. The enlarged fissures allow a larger quantity of water to enter which leads to a progressive enlargement of openings. Abundant small openings store a large quantity of water. The larger openings form a conduit system that drains the aquifer to springs. [15]

Characterization of karst aquifers requires field exploration to locate sinkholes, swallets, sinking streams, and springs in addition to studying geologic maps. [16] : 4  Conventional hydrogeologic methods such as aquifer tests and potentiometric mapping are insufficient to characterize the complexity of karst aquifers. These conventional investigation methods need to be supplemented with dye traces, measurement of spring discharges, and analysis of water chemistry. [17] U.S. Geological Survey dye tracing has determined that conventional groundwater models that assume a uniform distribution of porosity are not applicable for karst aquifers. [18]

Linear alignment of surface features such as straight stream segments and sinkholes develop along fracture traces. Locating a well in a fracture trace or intersection of fracture traces increases the likelihood to encounter good water production. [19] Voids in karst aquifers can be large enough to cause destructive collapse or subsidence of the ground surface that can initiate a catastrophic release of contaminants. [12] : 3–4  Groundwater flow rate in karst aquifers is much more rapid than in porous aquifers as shown in the accompanying image to the left. For example, in the Barton Springs Edwards aquifer, dye traces measured the karst groundwater flow rates from 0.5 to 7 miles per day (0.8 to 11.3 km/d). [20] The rapid groundwater flow rates make karst aquifers much more sensitive to groundwater contamination than porous aquifers. [16] : 1 

In the extreme case, groundwater may exist in underground rivers (e.g., caves underlying karst topography.

Fractured

If a rock unit of low porosity is highly fractured, it can also make a good aquifer (via fissure flow), provided the rock has a hydraulic conductivity sufficient to facilitate movement of water.

Map of major US aquifers by rock type Major US Aquifers by Rock Type.jpg
Map of major US aquifers by rock type

Human use of groundwater

This section is an excerpt from Groundwater § Uses by humans.[ edit ]
Reliance on groundwater will only increase, mainly due to growing water demand by all sectors combined with increasing variation in rainfall patterns. [21]

Challenges for using groundwater include: overdrafting (extracting groundwater beyond the equilibrium yield of the aquifer), groundwater-related subsidence of land, groundwater becoming saline, groundwater pollution.

By country or continent

Texas blind salamander found in Edwards Aquifer Texas blind salamander.jpg
Texas blind salamander found in Edwards Aquifer

Africa

Aquifer depletion is a problem in some areas, especially in northern Africa, where one example is the Great Manmade River project of Libya. However, new methods of groundwater management such as artificial recharge and injection of surface waters during seasonal wet periods has extended the life of many freshwater aquifers, especially in the United States.

Australia

The Great Artesian Basin situated in Australia is arguably the largest groundwater aquifer in the world [22] (over 1.7 million km2 or 0.66 million sq mi). It plays a large part in water supplies for Queensland, and some remote parts of South Australia.

Canada

Discontinuous sand bodies at the base of the McMurray Formation in the Athabasca Oil Sands region of northeastern Alberta, Canada, are commonly referred to as the Basal Water Sand (BWS) aquifers. [23] Saturated with water, they are confined beneath impermeable bitumen-saturated sands that are exploited to recover bitumen for synthetic crude oil production. Where they are deep-lying and recharge occurs from underlying Devonian formations they are saline, and where they are shallow and recharged by surface water they are non-saline. The BWS typically pose problems for the recovery of bitumen, whether by open-pit mining or by in situ methods such as steam-assisted gravity drainage (SAGD), and in some areas they are targets for waste-water injection. [24] [25] [26]

South America

The Guarani Aquifer, located beneath the surface of Argentina, Brazil, Paraguay, and Uruguay, is one of the world's largest aquifer systems and is an important source of fresh water. [27] Named after the Guarani people, it covers 1,200,000 km2 (460,000 sq mi), with a volume of about 40,000 km3 (9,600 cu mi), a thickness of between 50 and 800 m (160 and 2,620 ft) and a maximum depth of about 1,800 m (5,900 ft).

United States

The Ogallala Aquifer of the central United States is one of the world's great aquifers, but in places it is being rapidly depleted by growing municipal use, and continuing agricultural use. This huge aquifer, which underlies portions of eight states, contains primarily fossil water from the time of the last glaciation. Annual recharge, in the more arid parts of the aquifer, is estimated to total only about 10 percent of annual withdrawals. According to a 2013 report by the United States Geological Survey (USGS), the depletion between 2001 and 2008, inclusive, is about 32 percent of the cumulative depletion during the entire 20th century. [28]

In the United States, the biggest users of water from aquifers include agricultural irrigation and oil and coal extraction. [29] "Cumulative total groundwater depletion in the United States accelerated in the late 1940s and continued at an almost steady linear rate through the end of the century. In addition to widely recognized environmental consequences, groundwater depletion also adversely impacts the long-term sustainability of groundwater supplies to help meet the Nation’s water needs." [28]

An example of a significant and sustainable carbonate aquifer is the Edwards Aquifer [30] in central Texas. This carbonate aquifer has historically been providing high quality water for nearly 2 million people, and even today, is full because of tremendous recharge from a number of area streams, rivers and lakes. The primary risk to this resource is human development over the recharge areas.

See also

Related Research Articles

<span class="mw-page-title-main">Water table</span> Top of a saturated aquifer, or where the water pressure head is equal to the atmospheric pressure

The water table is the upper surface of the zone of saturation. The zone of saturation is where the pores and fractures of the ground are saturated with groundwater, which may be fresh, saline, or brackish, depending on the locality. It can also be simply explained as the depth below which the ground is saturated.

<span class="mw-page-title-main">Groundwater</span> Water located beneath the ground surface

Groundwater is the water present beneath Earth's surface in rock and soil pore spaces and in the fractures of rock formations. About 30 percent of all readily available fresh water in the world is groundwater. A unit of rock or an unconsolidated deposit is called an aquifer when it can yield a usable quantity of water. The depth at which soil pore spaces or fractures and voids in rock become completely saturated with water is called the water table. Groundwater is recharged from the surface; it may discharge from the surface naturally at springs and seeps, and can form oases or wetlands. Groundwater is also often withdrawn for agricultural, municipal, and industrial use by constructing and operating extraction wells. The study of the distribution and movement of groundwater is hydrogeology, also called groundwater hydrology.

<span class="mw-page-title-main">Hydrogeology</span> Study of the distribution and movement of groundwater

Hydrogeology is the area of geology that deals with the distribution and movement of groundwater in the soil and rocks of the Earth's crust. The terms groundwater hydrology, geohydrology, and hydrogeology are often used interchangeably, though hydrogeology is the most commonly used.

Permeability in fluid mechanics, materials science and Earth sciences is a measure of the ability of a porous material to allow fluids to pass through it.

In hydrogeology, an aquifer test is conducted to evaluate an aquifer by "stimulating" the aquifer through constant pumping, and observing the aquifer's "response" (drawdown) in observation wells. Aquifer testing is a common tool that hydrogeologists use to characterize a system of aquifers, aquitards and flow system boundaries.

Phreatic is a term used in hydrology to refer to aquifers, in speleology to refer to cave passages, and in volcanology to refer to a type of volcanic eruption.

<span class="mw-page-title-main">Vadose zone</span> Unsaturated aquifer above the water table

The vadose zone, also termed the unsaturated zone, is the part of Earth between the land surface and the top of the phreatic zone, the position at which the groundwater is at atmospheric pressure. Hence, the vadose zone extends from the top of the ground surface to the water table.

Fossil water, fossil groundwater, or paleowater is an ancient body of water that has been contained in some undisturbed space, typically groundwater in an aquifer, for millennia. Other types of fossil water can include subglacial lakes, such as Antarctica's Lake Vostok. UNESCO defines fossil groundwater as "water that infiltrated usually millennia ago and often under climatic conditions different from the present, and that has been stored underground since that time."

In science and engineering, hydraulic conductivity, is a property of porous materials, soils and rocks, that describes the ease with which a fluid can move through the pore space, or fracture network. It depends on the intrinsic permeability of the material, the degree of saturation, and on the density and viscosity of the fluid. Saturated hydraulic conductivity, Ksat, describes water movement through saturated media. By definition, hydraulic conductivity is the ratio of volume flux to hydraulic gradient yielding a quantitative measure of a saturated soil's ability to transmit water when subjected to a hydraulic gradient.

In hydrology, there are two similar but distinct definitions in use for the word drawdown:

In the field of hydrogeology, storage properties are physical properties that characterize the capacity of an aquifer to release groundwater. These properties are storativity (S), specific storage (Ss) and specific yield (Sy). According to Groundwater, by Freeze and Cherry (1979), specific storage, [m−1], of a saturated aquifer is defined as the volume of water that a unit volume of the aquifer releases from storage under a unit decline in hydraulic head.

Used in hydrogeology, the groundwater flow equation is the mathematical relationship which is used to describe the flow of groundwater through an aquifer. The transient flow of groundwater is described by a form of the diffusion equation, similar to that used in heat transfer to describe the flow of heat in a solid. The steady-state flow of groundwater is described by a form of the Laplace equation, which is a form of potential flow and has analogs in numerous fields.

<span class="mw-page-title-main">Overdrafting</span> Unsustainable extraction of groundwater

Overdrafting is the process of extracting groundwater beyond the equilibrium yield of an aquifer. Groundwater is one of the largest sources of fresh water and is found underground. The primary cause of groundwater depletion is the excessive pumping of groundwater up from underground aquifers. Insufficient recharge can lead to depletion, reducing the usefulness of the aquifer for humans. Depletion can also have impacts on the environment around the aquifer, such as soil compression and land subsidence, local climatic change, soil chemistry changes, and other deterioration of the local environment.

Groundwater models are computer models of groundwater flow systems, and are used by hydrologists and hydrogeologists. Groundwater models are used to simulate and predict aquifer conditions.

The groundwater energy balance is the energy balance of a groundwater body in terms of incoming hydraulic energy associated with groundwater inflow into the body, energy associated with the outflow, energy conversion into heat due to friction of flow, and the resulting change of energy status and groundwater level.

Porosity or void fraction is a measure of the void spaces in a material, and is a fraction of the volume of voids over the total volume, between 0 and 1, or as a percentage between 0% and 100%. Strictly speaking, some tests measure the "accessible void", the total amount of void space accessible from the surface.

<span class="mw-page-title-main">Willamette Lowland basin-fill aquifer</span>

The Willamette Lowland basin-fill aquifer is 31,000 km2, 12,000 square mile aquifer underlying the region of Oregon and parts of Washington (state) between the Oregon Coast Range and the Cascade Range. The aquifer shares a name with the local river, the Willamette River, originating from a Clackamas Chinook word. The "mette" of Willamette was used by the Clackamas to mean water or river. The Willamette valley is home to 70% of Oregon's population, with the aquifer supplying water for agricultural, domestic, and industrial purposes. Reported in 2005, the total water use from the aquifer was 1.6 hm3 per day, with 58% going to irrigation, 24% to public supply, and 18% to industrial use. In general, the aquifer withdraw is sufficiently compensated in the long term by recharge through precipitation, however regions of the aquifer have shown long term declines, including that regions underlain by the Columbia River basalt unit. However, during the dry season from June-September, withdrawals from the aquifer result is significant seasonal variations in the ground water table height, changing by more than 60 ft. In the state of Oregon, all water is publicly owned and maintenance and protection of water is done by the Oregon Water Resources Department and the Oregon Water Resources Commission. However, local governments can provide land use permits for aquifer use, notably, use for new rural residences.

Bioclogging or biological clogging refers to the blockage of pore space in soil by microbial biomass, including active cells and their byproducts such as extracellular polymeric substance (EPS). The microbial biomass obstructs pore spaces, creating an impermeable layer in the soil and significantly reducing water infiltration rates.

<span class="mw-page-title-main">Fault zone hydrogeology</span>

Fault zone hydrogeology is the study of how brittlely deformed rocks alter fluid flows in different lithological settings, such as clastic, igneous and carbonate rocks. Fluid movements, that can be quantified as permeability, can be facilitated or impeded due to the existence of a fault zone. This is because different mechanisms that deform rocks can alter porosity and permeability within a fault zone. Fluids involved in a fault system generally are groundwater and hydrocarbons.

<span class="mw-page-title-main">Coastal hydrogeology</span> Branch of hydrogeology

Coastal Hydrogeology is a branch of Hydrogeology that focuses on the movement and the chemical properties of groundwater in coastal areas. Coastal Hydrogeology studies the interaction between fresh groundwater and seawater, including seawater intrusion, sea level induced groundwater level fluctuation, submarine groundwater discharge, human activities and groundwater management in coastal areas.

References

  1. ↑ Walker, Kira (2022). "Ancient systems keep water flowing". Nature Middle East. Nature. doi:10.1038/nmiddleeast.2022.72. S2CID   253486495 . Retrieved 10 July 2023.
  2. ↑ "Aquifers and Groundwater". USGS. ...more than 30,000 feet. On average, however, the porosity and permeability of rocks decrease as their depth below land surface increases; the pores and cracks in rocks at great depths are closed or greatly reduced in size because of the weight of overlying rocks.
  3. ↑ "Aquifers". National Geographic Society. 2019-07-30. Retrieved 2021-09-17.
  4. ↑ "Types of aquifers: Aquiclude, Aquitard and Aquifuge and location of aquifers – Geography of Water Resources". ebooks.inflibnet.ac.in. Retrieved 2024-06-27.
  5. ↑ "Huge reserves of freshwater lie beneath the ocean floor". Gizmag.com. 11 December 2013. Retrieved 15 December 2013.
  6. ↑ Post, V. E. A.; Groen, J.; Kooi, H.; Person, M.; Ge, S.; Edmunds, W. M. (2013). "Offshore fresh groundwater reserves as a global phenomenon". Nature. 504 (7478): 71–78. Bibcode:2013Natur.504...71P. doi:10.1038/nature12858. PMID   24305150. S2CID   4468578.
  7. ↑ Freeze, R.A.; Cherry, J.A. (1979). Groundwater. Prentice-Hall. ISBN   978-0-13-365312-0. OCLC   643719314. Accessed from: http://hydrogeologistswithoutborders.org/wordpress/1979-english/ Archived 2020-04-06 at the Wayback Machine
  8. ↑ "Morphological Features of Soil Wetness". Ces.ncsu.edu. Archived from the original on 9 August 2010. Retrieved 6 September 2010.
  9. ↑ "Understanding Aquitards and Aquicludes | UNSW Connected Waters Initiative". www.connectedwaters.unsw.edu.au. Retrieved 2022-12-07.
  10. ↑ The energy balance of groundwater flow applied to subsurface drainage in anisotropic soils by pipes or ditches with entrance resistance. International Institute for Land Reclamation and Improvement (ILRI), Wageningen, The Netherlands. On line : Archived 2009-02-19 at the Wayback Machine . Paper based on: R.J. Oosterbaan, J. Boonstra and K.V.G.K. Rao, 1996, "The energy balance of groundwater flow". Published in V.P.Singh and B.Kumar (eds.), Subsurface-Water Hydrology, pp. 153–60, Vol. 2 of Proceedings of the International Conference on Hydrology and Water Resources, New Delhi, India, 1993. Kluwer Academic Publishers, Dordrecht, The Netherlands. ISBN   978-0-7923-3651-8 . On line : . The corresponding "EnDrain" software can be downloaded from : , or from :
  11. ↑ ILRI (2000), Subsurface drainage by (tube)wells: Well spacing equations for fully and partially penetrating wells in uniform or layered aquifers with or without anisotropy and entrance resistance, 9 pp. Principles used in the "WellDrain" model. International Institute for Land Reclamation and Improvement (ILRI), Wageningen, The Netherlands. On line : . Download "WellDrain" software from : , or from :
  12. 1 2 3 4 5 Assaad, Fakhry; LaMoreaux, Philip; Hughes, Travis (2004). Field methods for geologists and hydrogeologists. Berlin, Germany: Springer-Verlag Berlin Heidelberg. doi:10.1007/978-3-662-05438-3. ISBN   978-3-540-40882-6.
  13. 1 2 Pettijohn, Francis; Potter, Paul; Siever, Raymond (1987). Sand and Sandstone. New York: Springer Science+Business Media. doi:10.1007/978-1-4612-1066-5. ISBN   978-0-387-96350-1.
  14. ↑ Alley, William; Reilly, Thomas; Franke, O. (1999). Sustainability of ground-water resources . Circular 1186. Denver, Colorado: U.S. Geological Survey. p.  8. doi:10.3133/cir1186. ISBN   978-0-607-93040-5.
  15. ↑ Dreybrodt, Wolfgang (1988). Processes in karst systems: physics, chemistry, and geology. Springer Series in Physical Environment. Vol. 4. Berlin: Springer. pp. 2–3. doi:10.1007/978-3-642-83352-6. ISBN   978-3-642-83354-0.
  16. 1 2 Taylor, Charles (1997). Delineation of ground-water basins and recharge areas for municipal water-supply springs in a karst aquifer system in the Elizabethtown area, Northern Kentucky (PDF). Water-Resources Investigations Report 96-4254. Denver, Colorado: U.S. Geological Survey. doi:10.3133/wri964254.
  17. ↑ Taylor, Charles; Greene, Earl (2008). "Hydrogeologic characterization and methods used in the investigation of karst hydrology." (PDF). Field Techniques for Estimating Water Fluxes Between Surface Water and Ground Water. Techniques and Methods 4–D2. U.S. Geological Survey. p. 107. Archived (PDF) from the original on 2008-11-02.
  18. ↑ Renken, R.; Cunningham, K.; Zygnerski, M.; Wacker, M.; Shapiro, A.; Harvey, R.; Metge, D.; Osborn, C.; Ryan, J. (November 2005). "Assessing the Vulnerability of a Municipal Well Field to Contamination in a Karst Aquifer". Environmental and Engineering Geoscience. 11 (4). GeoScienceWorld: 320. Bibcode:2005EEGeo..11..319R. CiteSeerX   10.1.1.372.1559 . doi:10.2113/11.4.319.
  19. ↑ Fetter, Charles (1988). Applied Hydrology. Columbus, Ohio: Merrill. pp. 294–295. ISBN   978-0-675-20887-1.
  20. ↑ Scanlon, Bridget; Mace, Robert; Barrett, Michael; Smith, Brian (2003). "Can we simulate regional groundwater flow in a karst system using equivalent porous media models? Case study, Barton Springs Edwards aquifer, USA". Journal of Hydrology. 276 (1–4). Elsevier Science: 142. Bibcode:2003JHyd..276..137S. doi:10.1016/S0022-1694(03)00064-7. S2CID   16046040.
  21. ↑ United Nations (2022) The United Nations World Water Development Report 2022: Groundwater: Making the invisible visible. UNESCO, Paris Text was copied from this source, which is available under a Creative Commons Attribution 3.0 International License
  22. ↑ "The Great Artesian Basin" (PDF). Facts: Water Series. Queensland Department of Natural Resources and Water. Archived from the original (PDF) on 13 November 2006. Retrieved 3 January 2007.
  23. ↑ Joslyn North Mine Project: Environmental Impact Assessment Hydrologeology (PDF) (Report). Edmonton, Alberta: Deer Creek Energy. December 2005. p. 4. Archived from the original (PDF) on 2 December 2013.
  24. ↑ Barson, D., Bachu, S. and Esslinger, P. 2001. Flow systems in the Mannville Group in the east-central Athabasca area and implications for steam-assisted gravity drainage (SAGD) operations for in situ bitumen production. Bulletin of Canadian Petroleum Geology, vol. 49, no. 3, pp. 376–92.
  25. ↑ Griffiths, Mary; Woynillowicz, Dan (April 2003). Oil and Troubled Waters: Reducing the impact of the oil and gas industry on Alberta's water resources (PDF) (Report). Edmonton, Alberta: Pembina Institute. Archived (PDF) from the original on 2013-12-15.
  26. ↑ FMFN (June 2012). Fort McKay's Review of Teck Resources Ltd. – Frontier Oil Sands Mine Project Integrated Application (PDF) (Report). Fort McKay First Nation. Archived (PDF) from the original on 2013-06-20.
  27. ↑ Brittain, John (22 June 2015). "The International Atomic Energy Agency: Linking Nuclear Science and Diplomacy". Science and Diplomacy.
  28. 1 2 Konikow, Leonard F. Groundwater Depletion in the United States (1900–2008) (PDF) (Report). Scientific Investigations Report. Reston, VA: U.S. Department of the Interior, U.S. Geological Survey. p. 63. Archived (PDF) from the original on 2013-06-15.
  29. ↑ Zabarenko, Deborah (20 May 2013). "Drop in U.S. underground water levels has accelerated: USGS". Reuters. Washington, DC.
  30. ↑ "Edwards Aquifer Authority". Edwardsaquifer.org. Retrieved 15 December 2013.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.