Victorian Railways H class
Victorian Railways H class | |||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
![]() Builder's photograph of H220, 1941 | |||||||||||||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||||||||||||
| |||||||||||||||||||||||||||||||||||||||||||
|
The Victorian Railways H class was an express passenger steam locomotive operated by the Victorian Railways from 1941 to 1958. Intended to eliminate the use of double heading A2 class locomotives on The Overland services on the steeply graded Western line to Adelaide, wartime restrictions led to only one locomotive being built. Nicknamed Heavy Harry, H220 was the largest locomotive ever built in Australia and the largest non-articulated steam locomotive to run on Australian railways.
History
[edit]By 1923, the A2 class 4-6-0 locomotives, which dated back to 1907, were frequently double-heading on interstate expresses to Serviceton and Albury, because increasing traffic saw loads exceed the eight-car maximum of a single A2. The Victorian Railways Commissioners recommended considerably more powerful locomotives, that could haul trains of up to eleven cars unassisted over the ruling gradients on those lines.[1] The S class 4-6-2 Pacifics displaced the A2s from North East line express services from 1928 onwards and allowed a faster timetable to be introduced. However, a Pacific-type locomotive was not well suited to the Western line. The section between Melbourne and Ballarat had sharply-curved, steep inclines, the most notorious of which was the 10-mile (16 km), 1 in 48 (2.08%) ruling gradient of the Ingliston Bank.[2] As early as 1923, VR locomotive designers were considering 4-8-2 Mountain-type locomotives for the purpose, along with the use of a third cylinder to provide increased power without exceeding the loading gauge.[1] The Victorian Railways H class was the third-most-powerful non-articulated steam locomotive to operate in Australia, after the NSWGR D57 4-8-2 and the South Australian Railways 500/500B class.
Design brief
[edit]![]() |
![]() |
Detail of the connecting rod for the third cylinder (left), and valve gear stem and crosshead guide, located between the outside cylinders. (right) |
![](http://upload.wikimedia.org/wikipedia/commons/thumb/f/fd/H220motion3.jpg/300px-H220motion3.jpg)
In 1936, the Victorian Railways Design Office finalised the major design requirements for a steam locomotive that was capable of hauling a load of 550 long tons (560 t; 620 short tons) at a minimum 20 miles per hour (32 km/h) up the Ingliston Bank unassisted.[2] In order to develop the power required, a very large grate and a very large boiler were needed, and the 4-8-4 wheel arrangement enabled that, because its four-wheeled trailing truck could support a large firebox, and four coupled axles would support a large boiler and ensure a good factor of adhesion.
VR designers wanted to improve on aspects of the earlier S class design. Those three-cylinder Pacifics, although capable of hauling heavy loads at high speed, had proved to be relatively maintenance-intensive, particularly with regard to servicing the valve gear and motion for the third (inside) cylinder. The Gresley conjugated valve gear, driven from the valve spindles of the outside cylinder piston valves, was prone to heat expansion and wear, causing timing difficulties, and it required dismantling and removal whenever the centre cylinder valve needed to be serviced.[3]
To overcome those problems, the H class was provided with a significantly different arrangement for its third cylinder. Rather than the Gresley mechanism, it had German Henschel & Son conjugated valve gear apparatus, driven from the combination levers of the Walschaert valve gear for the outside cylinders.[4][5] The inside cylinder was also positioned further forward of the outside cylinders, and it drove the leading coupled axle, with the outside cylinders driving the second coupled axle.[6][7]
The H class also became the first VR locomotive to feature a mechanical stoker, and boasted many other modern features, such as roller bearings, hydrostatically controlled load compensating brake gear on the tender,[8] power-operated reversing gear, American-style bar frame construction, thermic siphons, and duplex blast pipes.[6]
Production
[edit]Construction of three H class locomotives at Newport Workshops commenced in 1939 and three sets of frames were manufactured.[9] However, work was halted due to the outbreak of World War II. A shortage of motive power, caused by increased wartime traffic, led to the completion of class leader H220 being authorised and the locomotive entered service on 7 February 1941.[10][11] Streamlining, similar to that on the S class locomotives, was originally planned, but wartime economies saw that abandoned.[12][13]
The two additional, partly-built, H class locomotives remained incomplete while wartime production of armaments (and later postwar rebuilding of badly run-down infrastructure) took precedence over express passenger locomotive construction. They were never completed,[14] and the parts were subsequently scrapped.
Service life
[edit]![](http://upload.wikimedia.org/wikipedia/commons/thumb/6/64/H220-Essendon.jpg/300px-H220-Essendon.jpg)
Although it had been built to work the Western line to Ararat, a number of bridges along the route required strengthening before the H class locomotive, with its 23+1⁄4 long tons (23.6 t; 26.0 short tons) axle load, could enter regular service on the line. The necessary work was deferred due to wartime restrictions on available resources. Therefore, H220 was put to work on the North-Eastern line to Albury, the only line able to accommodate its loading gauge and high axle load. It mostly hauled fast goods services, but it also powered express passenger services, troop trains and, on the odd occasion when the regular S class Pacific was not available, the Spirit of Progress. That was particularly the case in the postwar period, when S class locomotives were affected by poor coal and reduced availability.[15] H220 gave an indication of its capabilities on one such run of the Spirit in the late 1940s, when it reportedly topped the 5-mile (8 km)-long 1 in 50 Glenroy Bank at 45 mph (72 km/h), three times the typical S class-hauled speed at that same point.[16] It went on to pass Seymour 13 minutes ahead of schedule, and arrived at Albury at 20 minutes ahead of the 10:40 pm scheduled arrival time.[17]
H220 never operated in its intended role as motive power for The Overland, although it did make a brief appearance on the Western line in 1949, when it ran a series of trials on goods trains from Melbourne to Ballarat, being assessed by the VR dynamometer car. Results from the dynamometer car showed that the locomotive developed around 3,300 drawbar horsepower (2,460 kW) at 47.5 mph (76.4 km/h), and a starting drawbar tractive effort of 52,000 lbf (230 kN).[18] The Australian Railway Historical Society, in listing the introduction of H220 among its "100 defining aspects of Australian railways", noted that test results as high as 3,600 hp (2,700 kW) at 50 mph (80 km/h) were recorded, a power output unequalled in Australia during the steam era, and only equalled in the modern era by the National Rail NR class diesel-electric locomotives.[19]
Although intended for express passenger use, H220 was found to be particularly effective when used as a fast goods locomotive. It typically hauled five return trips a week between Melbourne and Wodonga, covering around 1,875 miles (3,018 km) per week, and hauling loads of up to 820 tons (833 t) over the 1 in 50 gradients on that line.[20] By comparison, the maximum loads between Wodonga and Melbourne of the C class 2-8-0 and X class 2-8-2 heavy goods locomotives were 555 and 650 tons respectively. H220 was also able to complete the journey in a much shorter time, with its large tender requiring only a single stop for water, rather than the two stops for water and coal that the other locomotives required.[21] Even after the introduction of mainline diesel-electric traction from 1952 onwards, Victorian Railways' promotional literature featured H220 prominently. One advertisement in Walkabout in November 1953, headed "Trains we are proud of", promoted H220 as "Australia's mightiest engine" and noted its nightly service hauling the 21:25 Albury Interstate Fast Freight.[22]
From all accounts, H220 was a success, even though it spent its life hauling services and operating on a line it was not specifically designed for. Although one-off locomotives are often consigned to a short operating life, or underutilised due to non-standardisation of parts and maintenance requirements, H220 remained in service until finally being superseded by diesel electric locomotives in the late 1950s. In a service life of 15 years 3 months, it clocked up a total of 821,860 miles (1,322,660 km),[6] averaging over 4,800 miles per month.
Demise
[edit]Even after the war, upgrades on the line to Ararat necessary for H class operation were not made, as the VR struggled with a backlog of maintenance work which had built up during the 1940s. When the VR finally embarked on major capital investment in the early 1950s, diesel and electric traction was under consideration. Although diesel locomotives of the early 1950s typically had far lower power outputs than the H class, they could be run in multiple-unit operation, with one crew controlling two or more locomotives. In August 1952, two new B class diesel-electric locomotives established their credentials during trials by hauling a 1,121 long tons (1,139 t; 1,256 short tons) goods train up the Ingliston Bank, and covering in 44 minutes the same distance two A2 class locomotives took to haul a 690-long-ton (700 t; 770-short-ton) load in 67 minutes.[23][24] The B class locomotives proved their ability to provide the same (if not better) performance as the H class, but without the heavy axle load or the need for upgraded infrastructure. They became the new motive power for not only The Overland, but also mainline goods services. The days of mainline steam locomotives were numbered.
H220 continued in service until it was withdrawn for an overhaul on 20 May 1956.[25] By that time, the C and X class heavy goods locomotives were being progressively withdrawn from service and scrapped, having been made redundant by B class diesel-electric and L class electric locomotives. H220 was stored rather than overhauled, and never returned to service. It was written off the VR locomotive register on 30 April 1958.[25]
Preservation
[edit]![](http://upload.wikimedia.org/wikipedia/commons/thumb/6/60/H220.jpg/300px-H220.jpg)
H220 survived more-or-less intact until 1960, when the Australian Railway Historical Society successfully lobbied for the establishment of a railway museum. H220 entered the museum in 1962, and since this date has been its star exhibit.
In April 2008, 50 years after its official withdrawal from service, H220 was added to the Victorian Heritage Register. Heritage Council chairman Chris Gallagher noted that H220 represented the peak of steam motive power technology in Victoria and warranted the state's highest level of heritage protection.[26] In October 2020, a new roof, announced by local MP Melissa Horne in May 2019, was built over H220 and neighbouring exhibits to protect them from the weather.[27]
It is believed that H220 is the world's only remaining example of a three-cylinder 4-8-4.[28]
References
[edit]- Dee; et al. (1981). Power Parade. Melbourne: VicRail Public Relations Division. ISBN 978-0-7241-3323-9.
- Pearce; et al. (1980). North Williamstown Railway Museum. Melbourne: ARHS. ISBN 978-0-85849-018-5.
Specific
- ^ a b "NEW LOCOMOTIVES". The Argus. Melbourne: National Library of Australia. 26 September 1923. p. 22. Retrieved 12 February 2012.
- ^ a b "ARHS Railway Museum: What to see – H220". Archived from the original on 25 January 2008. Retrieved 15 October 2006.
- ^ Oberg, Leon (2007). Locomotives of Australia 1854–2007. Rosenberg Publishing. p. 201. ISBN 978-1-877058-54-7.
- ^ Lee, Robert (2007). The Railways of Victoria 1854–2004. Melbourne University Publishing Ltd. p. 165. ISBN 978-0-522-85134-2.
- ^ "Public Records Office Victoria – VPRS 12800/P1 H 4584C". Archived from the original on 28 September 2007. Retrieved 6 November 2006.
- ^ a b c Pearce et al., p. 19
- ^ "Australia's Largest Locomotive" Locomotive, Railway Carriage & Wagon Review issue 588 August 1941 pages 164/165
- ^ Dunn; et al. (2006). Super Power on the VR: Victorian Railways 4-8-4 'H' Class Pocono. Melbourne: Train Hobby Publications. p. 31. ISBN 1-921122-07-2.
- ^ "AHRS Railway Museum: History 1900–1950". Australian Railway Historical Society. Archived from the original on 19 July 2008. Retrieved 4 May 2008.
- ^ "New 4-8-4 Type Locomotive" Railway Gazette 9 May 1941 page 522
- ^ "4-8-4 Locomotive" Locomotive, Railway Carriage & Wagon Review issue 585 May 1941 pages 99/100
- ^ "New H Class 4-8-4 Locomotives" Railway Gazette 27 January 1939 page 133
- ^ "New Streamlined 4-8-4 Express Locomotives" Locomotive, Railway Carriage & Wagon Review issue 560 April 1939 page 98
- ^ Dunn; et al. (2006). Super Power on the VR: Victorian Railways 4-8-4 'H' Class Pocono. Melbourne: Train Hobby Publications. p. 15. ISBN 1-921122-07-2.
- ^ ""HEAVY HARRY" INVALUABLE IN EMERGENCY". The Argus. Melbourne: National Library of Australia. 26 May 1949. p. 3. Retrieved 15 November 2012.
- ^ "L 1150 makes the grade". The Victorian Railways Newsletter. May 1953. Retrieved 26 May 2007.
- ^ Holmes, Lloyd (February 1991). "Some memories of H 220". Newsrail. Volume. Vol. 19, no. 2. p. 44. ISSN 0310-7477.
- ^ "Public Record Office Victoria – VPRS 12903/P1 Box 626/08 Dynamometer Car Tests Locomotive H220". Archived from the original on 28 September 2007. Retrieved 8 November 2006.
- ^ "100 defining aspects of Australian railways" (PDF). Australian Railway Historical Society. Archived from the original (PDF) on 16 July 2011. Retrieved 10 May 2008.
- ^ Dunn; et al. (2006). Super Power on the VR: Victorian Railways 4-8-4 'H' Class Pocono. Melbourne: Train Hobby Publications. p. 28. ISBN 1-921122-07-2.
- ^ "Giant Locomotive". Morwell Advertiser. Morwell, Vic.: National Library of Australia. 12 April 1945. p. 8. Retrieved 15 February 2012.
- ^ "Railway Planned Service – Trains we are proud of". Walkabout. November 1953.
- ^ "DIESELS IN FAST HAUL". The Courier-Mail. Brisbane: National Library of Australia. 21 August 1952. p. 1. Retrieved 29 October 2012.
- ^ "Public Record Office Victoria VPRS 12800/P1 H 2545". Archived from the original on 14 October 2009. Retrieved 8 November 2006.
- ^ a b "H 220 maintenance history card". Retrieved 29 October 2012.
{{cite journal}}
: Cite journal requires|journal=
(help) - ^ Tzobanakis, Stella (29 April 2008). "Heavy metal gong". Hobsons Bay Leader. leadernews.com.au. Retrieved 20 April 2009.
- ^ Dmytryshchak, Goya (15 May 2019). "Wild about Heavy Harry". Star Weekly: Maribyrnong & Hobsons Bay. starweekly.com.au.
- ^ (based on SNCF 242A1 and DR BR 06 4-8-4 locomotives being scrapped) "VICTORIAN RAILWAYS H CLASS 4-8-4". Archived from the original on 11 October 2007. Retrieved 6 November 2006.
External links
[edit]![](http://upload.wikimedia.org/wikipedia/en/thumb/4/4a/Commons-logo.svg/30px-Commons-logo.svg.png)
- victorianrailways.net Glenroy Bank – comparison photographs of H220 (in 1941) and a modern V/Line diesel electric locomotive (in 2004) both hauling passenger services past the same vantage point, 63 years apart.
- victorianrailways.net Seymour – H220 on a livestock train, circa 1950. The valance below the cab appears to have been removed by this time.
- Museum of Victoria – Victorian Railways – H Class Loco 'Heavy Harry'
- Wandong Live Steam – Photograph of a 5" gauge live steam model of H220, adjacent to a New York Central Railroad 4-8-2 'Mohawk'. An interesting comparison of the relative loading gauge constraints of the VR and NYCRR, most notably the 14' height constraint of the VR.