Talk:Turbine
This is the talk page for discussing improvements to the Turbine article. This is not a forum for general discussion of the article's subject. |
Article policies
|
Find sources: Google (books · news · scholar · free images · WP refs) · FENS · JSTOR · TWL |
![]() | This ![]() It is of interest to the following WikiProjects: | |||||||||||||||||||||||||||||||||||||||||||||||||||
|
transonic turbine
[edit]This bit says that near supersonic speeds the turbine has a reduced efficiency. Are the rear turbines in a jet engine just inefficient, as the air is certainly supersonic in some of them? Or can turbines become more efficient at completly supersonic speeds? cc 24.137.78.34 00:22, 3 March 2006 (UTC)
"Turbine" is also a mathematical term: http://mathworld.wolfram.com/Turbine.html
-Todd
re-write
[edit]I re-wrote this page. Some of the material was already covered in Gas turbine or Steam turbine. And some of the material I moved to Steam turbine.
Also; organized, added theory, added sections and added external links. Pud 03:11, 17 Jun 2004 (UTC)
Quasiturbine
[edit]I removed the recent Quasiturbine entries, it belongs here about as much as rotary engine. Duk 06:25, 9 Dec 2004 (UTC)
removed material
[edit]I removed the following material since its un-organized and doesn't really belong on this page. Some of it would be better at gas turbine or jet engines;
- cooled turbine
Modern gas turbine engines often feature one, or more, air-cooled turbine stages. Relatively cool air, bled-off the compression system, is piped around the combustor and fed into the hollow turbine rotor blades and/or vanes, to prevent them melting in the hot gas stream. The used cooling air is dumped, eventually, into the main gas stream.
- high pressure turbine
In a multi-shaft gas turbine, the first turbine downstream of the combustor is usually called the high pressure (i.e. HP) turbine. Normally the HPT is a one or 2 stage unit, the latter usually being more efficient.
- intermediate pressure turbine
In 3 shaft gas turbine engines, (e.g. Rolls-Royce Trent), the middle unit in the turbine expansion system is often called the intermediate pressure (i.e. IP) turbine. The IPT is usually a single stage unit (i.e. a single row of stators, followed by a row of rotor blades).
- low pressure turbine
In a multi-shaft gas turbine, the last unit in the turbine expansion system, is usually called the low pressure (i.e. LP) turbine. Number of stages in an LPT can range from one to 7, or even more, depending on the load imposed.
- power turbine
In turboprop and turboshaft engines, the LP turbine is often called the power turbine
- transonic turbine
In most of the turbines employed in gas turbine engines, the flow exiting the nozzle guide vanes (NGV's) is at a high subsonic Mach number (e.g. 0.85). In a transonic turbine, the flow exits the NGV's at supersonic velocity, increasing the work capacity of the unit, albeit with a penalty on efficiency.
- statorless turbine
Most turbines have a set of stators or NGV's to direct the gas onto the turbine rotor blades. In a statorless turbine,(e.g. GE YF120 variable cycle engine) the exit swirl in the gasflow from a preceding turbine rotor is directed onto another contra-rotating rotor stage, situated immediately downstream. The work capacity of the statorless unit is, however, somewhat lower than normal.
- rotating stator turbine
Usually, being 'earthed' to the engine frame, the stators of a turbine are stationary. However, in the GE36 (UDF) propfan demonstrator engine, the 7 stage power turbine drives a set of contra-rotating propfan blades. The turbine rotors drive one set of propfan blades, whilst the 'unearthed' stators drive the other set of blades, in the opposite direction!
- shrouded turbine
Most turbine rotor blades have a shroud at the tip, which incorporates a seal, to minimize overtip leakage from the high pressure at inlet to the low pressure, downstream. One disadvantage of the shroud is that the extra mass imposes additional centrifugal stress on the aerofoil and the disc which holds the rotor blades. Another disadvantage is the shroud has to be cooled.
- unshrouded turbine
Today, some turbine rotor blades are unshrouded. However, careful design is required to prevent the tips of the blades suffering a 'haircut' (i.e. tip rub) under extreme conditions (e.g. high 'g' maneuver).
Modern aircraft are often fitted with a ram air turbine, which provides emergency electrical power, should the normal source of this power (i.e. offtake from the propulsion system) be lost. With unducted rotor blades, the unit behaves like a small windmill, extracting power from the external airstream. The unit is normally stowed within the airframe, to minimize drag, but automatically pops-out into the airstream if there is a power emergency.
Turbine driven fuel (or oxidizer) pump used in rocket motors and ramjet engines. Rockets often use a highly reactive chemical process to generate hot gases to drive the turbine, whereas ramjets usually use ram air.
betz limit and efficiency of turbines in air
[edit]in the solar updraft tower there are turbines ... are these turbines limited by the betz limit?
also: how efficient are turbines?--Flexme 01:55, 11 July 2006 (UTC)
Turbine operating in reverse
[edit]I claim that a turbine "operating in reverse" is not any compressor, but specifically a centrifugal compressor (also called a turbo compressor). E.g. a "reversed" piston compressor is a combustion engine (Otto cycle engine), not a turbine. The expression "operating in reverse" should probably be rephrased: A turbine operates inversely to a centrifugal compressor.--EvenT 20:40, 1 August 2006 (UTC)
- How about axial compressor then? Meggar 02:34, 3 August 2006 (UTC)
- An axial compressor is close to operating inversely to a turbine and could be included in the sentence. A centrifugual compressor is however closer by having curved blades like most turbines, while an axial compressor has straight blades. A reciprocating compressor or a screw compressor are far from being candidates.--EvenT 19:52, 4 August 2006 (UTC)
- We disagree only on the nomenclature. I believe that the two relevant wiki articles have it about right. Axial compressor has multistage airfoil shaped rotor and stator blades, along the lines of a turbine. Centrifugal compressor uses an impeller, often only one, followed by a diffuser stage. The impeller will have fins but not discrete blades. The only question is whether “axial compressor” is a good general name for the device. It is correct in the gas-turbine field of course. The second image now in the article is actually a centrifugal impeller, unhelpfully labeled “turbine” on the source page, and should be replaced.
Meggar 04:36, 17 August 2006 (UTC)
- is actually a centrifugal impeller -- no it isn't, it's a turbine wheel. Did you read the image source page at [1] ?--Duk 08:51, 21 October 2006 (UTC)
- Further down on that page is an image of a differently shaped part also with a "turbine" caption. Clearly the term is used there loosely for any spinning engine part. There is nothing wrong with that on a page about a fabrication process, just so we don't let it make the wiki article less clear. Meggar 20:44, 17 November 2006 (UTC)
- Both turbines and compressors may be of either radial or axial design, or somewhere in between. For example, see Image:Turbocharger.jpg - one side is a turbine and the other side is a compressor - both are a radial design. So yes, [2] labels two different designs as turbines -- not because they are applying the term loosely to any spinning part, but because turbines come in various different designs. The article could be expanded to cover this. I think an image gallery near the end showing different designs would be useful (if the images are carefully chosen). You can also get a good idea of different designs by searching for "Axial turbines" and "Radial turbines"--Duk 22:29, 17 November 2006 (UTC)
- Yes, carefully chosen and well explained images later in the article. Pud's image with parts in the housing is great. An indeterminate, unexplained image at the front of the article from a source page about a fabrication process is poor. Meggar 22:52, 17 November 2006 (UTC)
- Better keep your eye on that User:Pud! I originally added the image to the article because it was the best public domain image of a radial design that I came across (at the time). Considering this thread, I think having an image of a radial design is especially important. --Duk 23:03, 17 November 2006 (UTC)
- Yes, carefully chosen and well explained images later in the article. Pud's image with parts in the housing is great. An indeterminate, unexplained image at the front of the article from a source page about a fabrication process is poor. Meggar 22:52, 17 November 2006 (UTC)
- Both turbines and compressors may be of either radial or axial design, or somewhere in between. For example, see Image:Turbocharger.jpg - one side is a turbine and the other side is a compressor - both are a radial design. So yes, [2] labels two different designs as turbines -- not because they are applying the term loosely to any spinning part, but because turbines come in various different designs. The article could be expanded to cover this. I think an image gallery near the end showing different designs would be useful (if the images are carefully chosen). You can also get a good idea of different designs by searching for "Axial turbines" and "Radial turbines"--Duk 22:29, 17 November 2006 (UTC)
- Further down on that page is an image of a differently shaped part also with a "turbine" caption. Clearly the term is used there loosely for any spinning engine part. There is nothing wrong with that on a page about a fabrication process, just so we don't let it make the wiki article less clear. Meggar 20:44, 17 November 2006 (UTC)
- is actually a centrifugal impeller -- no it isn't, it's a turbine wheel. Did you read the image source page at [1] ?--Duk 08:51, 21 October 2006 (UTC)
- While we are on the subject of nomenclature . . .
When I worked for Rotoflow (General Electric) in the 1970's they had the unique distinction of calling the turboexpander turbine the "rotor" and the compressor the "impeller".
While this may not be accurate by definition (impeller = One that impels, as a rotating device used to force a fluid in a desired direction under pressure. A rotor or rotor blade. - Yahoo Dictionary) it does show a need to define and distinguish the two applications . . . one that is driven by the fluid . . . one that drives the fluid.
Morehugh 21:53, 16 January 2007 (UTC)
- While we are on the subject of nomenclature . . .
Useful image
[edit]I'm not a subject expert, and the article has too many images already, but Image:Turbines impulse v reaction.png seems like a pretty informative image that should be added somewhere in this article. I don't think I could have understood the difference between impulse and reaction turbines so quickly without it. --Interiot 18:39, 10 November 2006 (UTC)
- How about this:
- replace the first four images with Image:Dampfturbine Montage01.jpg in the intro.
- add the one you've noted to theory section (important to try to explain the difference between impulse and reaction turbines, but very hard to do)
- Image:Turbinengvrotor.gif should eventually be redone as an svg
- I'm not opposed to a thumbnail gallery near the end if it carefully selects images to illustrate different designs (water, wind, radial, centrifugal, impulse, reaction ... ) --Duk 19:40, 10 November 2006 (UTC)
Why RMS Lusitania?
[edit]Why does the see also section have a link to RMS Lusitania? The article notes that she had steam turbines, but makes no special mention otherwise. The first turbine powered merchant vessel was the Clyde steamer TS King Edward, built in 1901. References available on request, must try to get round to writing an article for that ship sometime. .. dave souza, talk 09:26, 10 February 2008 (UTC)
The internal structure and illistration of a hydro eletric turbine
[edit]i want to know the answer to the headline i posted. Additions by anyone with some personal expierience or good knowledge would be greatly appreciated —Preceding unsigned comment added by 67.167.231.242 (talk • contribs) 08:08, 21 April 2008
- This talk page is for discussions on improvements to the article. Questions like you put above, can be asked at the reference desk. Crowsnest (talk) 12:38, 21 April 2008 (UTC)
Bi-directional turbine
[edit]I recently heard about a bi-directional turbine used for generating electricity from waves - basically set in a hole in a cliff/shore line. The wave breaks and water is channeled through the turbine, generating electricity then the returning water drives the turbine from the opposite direction. Does anyone know anything about this? It would appear to be an obvious omission if I have my facts straight. Purple Aubergine (talk) 22:43, 7 July 2008 (UTC)
- As it's a type of water turbine it would be better to ask there - it sounds like an application of one of the standard turbine types. Hydroelectricity would be the relevent article.
Fluid couplings
[edit]Fluid couplings and torque converters - should they be mentioned here - being both turbines and impellors.? FengRail (talk) 17:06, 13 April 2009 (UTC)
Buoyancy turbines
[edit]http://picasaweb.google.ca/evexano/UntitledAlbum —Preceding unsigned comment added by 99.199.26.97 (talk) 23:41, 1 June 2009 (UTC)
TURBINE BLADES
[edit]Ok. And where is the "Turbine blades"? Somebody deleted this article, but this blades are almost absent in this article. This is very interesting theme and necessary to creat individual article. Sorry my bad English. ---- Pretenderrs =TALK= —Preceding undated comment added 20:03, 1 July 2009 (UTC).
Definition
[edit]A turbine is the whole of a rotor and stator (or a electrical generator without the blades). Turbines are thus only used in electrical generators.— Preceding unsigned comment added by 81.245.90.148 (talk)
-->this correct ?, if so, change the definition of article.— Preceding unsigned comment added by 81.245.90.148 (talk)
- No, it's not correct - in fact it's completely false. - BilCat (talk) 03:35, 21 October 2009 (UTC)
OTHER
[edit]Weeding Windmill - this is a certain type of windmill that produces vasts amount of pump.
No other source on the web appears to know what a "weeding windmill" is, although it seems to be a headword. The sentence is also moderately illiterate. Vandalism? Lee-Anne (talk) 01:33, 13 June 2010 (UTC)
Impulse Turbine - Reaction Turbine
[edit]I do not understand the connection between the two pictures describing the reaction turbine. The top picture has no blades, and the middle picture has no nozzels. Bo Jacoby. —Preceding unsigned comment added by 80.163.2.94 (talk) 13:35, 26 January 2011 (UTC)
Nothing...absolutely nothing...so much worth doing as messing around with boats
[edit]- Turbinia:the world's first tubine-driven ship
- New Scientist, April 1960 ...the ship is to be reassembled...'
--Wtshymanski (talk) 23:54, 17 August 2011 (UTC)
- Still just semantics, and better argued at Talk:Turbina, but at least he added a source. Perhaps we should reword the phrase to avoid the use of ship or boat? WTS suggested "yacht", which is better than "large mobile floating thing on water". - BilCat (talk) 00:17, 18 August 2011 (UTC)
- In the last hour or two on Google Books I've seen Turbinia called a ship, a steam launch, a "special vessel", a "steamer", a steam yacht... No idea what the preponderance of sources say; does it matter, really? Maybe someone has a crisp definition of what things floating in the water are called; certainly the most potentially lethal warships ever made are called "boats" by their crews, and they are much bigger than the Turbinia. I tried to find a picture of a dinghy on the aft deck of the Turbinia but all the pictures favor that high speed bow wave, or show it broken after the collision. --Wtshymanski (talk)
- I've always called it a boat, but Parsons' contemporary description sources quite clearly as "launch".
- The point is that it isn't a ship, and this is also an important description for steam turbines.
- Steam turbines were no use for marine propulsion - and they remained of little use for large ships until the geared turbine, some decades later. Compared to their piston contemporaries (which were highly developed by this time, far in excess of steam locomotive practice) they were too powerful and too fast. A steam turbine (even now) is a pain to use, having slow warm-up times and serious problems with inefficiency if run at fractional power. For marine propulsion, circa 1900 or before, they were too powerful for a small boat, too complex to justify themselves if made smaller, yet also too fast a shaft speed to allow themselves to be coupled to the slow-speed screws of a slower ship. Parsons wasn't the first to contemplate adding a turbine to a ship or boat, but others rejected it for these reasons.
- Parsons built Turbinia with a specific market in mind - the Navy. He'd realised that there was a niche for turbines, even as they were, and that was the torpedo boats and torpedo boat destroyers that were then under such active development. Here was a niche that needed high power, light weight and also could use (or at least tolerate) the high shaft speed that was still inevitable for turbines. So Turbinia is broadly a TBD hull, although even narrower in the beam.
- Turbinia was not a ship - no one could build a credible large ship with turbines for another 10 years, even on a naval budget. Parsons had no interest in advertising ever larger turbines at ship scale, he recognised they were as yet unsaleable, but he did see that a faster TBD was something that the Admiralty would (and did) take an immediate interest in.
- Andy Dingley (talk) 09:02, 18 August 2011 (UTC)
- Interesting, but other than the Parson's cite, it's all your OR as written. Other sources do call the Turbina a ship, as WTS has shown. - BilCat (talk) 09:10, 18 August 2011 (UTC)
- Your sources? An 11 page pamphlet, and a news article that calls it in turn a craft, launch and ship. Compelling. Andy Dingley (talk) 09:15, 18 August 2011 (UTC)
- Interesting, but other than the Parson's cite, it's all your OR as written. Other sources do call the Turbina a ship, as WTS has shown. - BilCat (talk) 09:10, 18 August 2011 (UTC)
- Glad you think so, as they do show a variety of terms are often used. Since you've cited the text to support "steam launch), as requested, and no one has challenged the text since, perhaps we can move on now. - BilCat (talk) 09:40, 18 August 2011 (UTC)
There is a change from the top of the article between what is impulse and what is reaction. Rateau at the bottom is referred to as impulse. Rateau is referred to as impulse at the bottom portion of the article, but is usually referred to as reaction as shown in the diagram on the top. Curtis bucket type are impulse as shown in the same diagram at the top. 207.11.243.2 (talk) 17:12, 20 February 2019 (UTC)Wilfred Lyon
A Commons file used on this page has been nominated for deletion
[edit]The following Wikimedia Commons file used on this page has been nominated for deletion:
Participate in the deletion discussion at the nomination page. —Community Tech bot (talk) 12:37, 12 July 2019 (UTC)
Parson or De Laval
[edit]Didn’t De Laval develope the first commercial reaction turbine. His seperator used a reaction turbine? Also aren’t the turbines used in power plants reaction+impulse turbines. --94.191.131.65 (talk) 08:49, 14 February 2020 (UTC)
Safety issue with first image
[edit]The first image shows incorrect rigging practices- maybe find a similar image that shows rigging that follows current safety guidelines. 2600:1014:B030:5A2:E13E:7E2B:6E8E:8F1C (talk) 22:10, 12 September 2023 (UTC)
- C-Class vital articles
- Wikipedia level-4 vital articles
- Wikipedia vital articles in Technology
- C-Class level-4 vital articles
- Wikipedia level-4 vital articles in Technology
- C-Class vital articles in Technology
- C-Class Engineering articles
- High-importance Engineering articles
- WikiProject Engineering articles
- C-Class aviation articles
- C-Class aircraft articles
- WikiProject Aircraft articles
- C-Class aircraft engine articles
- Aircraft engine task force articles
- WikiProject Aviation articles
- C-Class energy articles
- High-importance energy articles