Speakon connector
![]() | This article has multiple issues. Please help improve it or discuss these issues on the talk page. (Learn how and when to remove these template messages)
|
![](http://upload.wikimedia.org/wikipedia/commons/thumb/e/e6/Neutrik_Speakon.jpg/220px-Neutrik_Speakon.jpg)
![](http://upload.wikimedia.org/wikipedia/commons/thumb/3/36/Connectors_of_a_QSC_PLX2402_professional_PA_Power_Amplifier.jpg/220px-Connectors_of_a_QSC_PLX2402_professional_PA_Power_Amplifier.jpg)
The Speakon (stylized speakON) is a trademarked name for an electrical connector,[2] originally manufactured by Neutrik, mostly used in professional audio systems for connecting loudspeakers to amplifiers. Other manufacturers make compatible products,[3] often under the name "speaker twist connector".
Speakon connectors are rated for at least 30 A RMS continuous current,[4] higher than 1/4-inch TS phone connectors, two-pole twist lock, and XLR connectors for loudspeakers.[5]
Design
[edit]A Speakon connector is designed with a locking system that may be designed for soldered or screw-type connections. Line connectors (male) mate with (female) panel connectors and typically a cable will have identical connectors at both ends. If it is needed to join cables, a coupler can be used (which essentially consists of two panel connectors mounted on the ends of a plastic tube). The design was conceived in 1987.[6]
Speakon connectors are designed to be unambiguous in their use in speaker cables. With 1/4" speaker jacks and XLR connections, it is possible for users to erroneously use low-current shielded microphone or instrument cables in a high-current speaker application. Speakon cables are intended solely for use in high current audio applications.
Speakon connectors arrange their contacts in two concentric rings, with the inner contacts named +1, +2, etc. and the outer contacts connectors (in the four-pole and eight-pole version only) named −1, −2, etc.[7] The phase convention is that positive voltage on the + contact causes air to be pushed away from the speaker.
Speakon connectors are made in two, four and eight-pole configurations. The two-pole line connector will mate with the four-pole panel connector, connecting to +1 and −1; but the reverse combination will not work. The eight-pole connector is physically larger to accommodate the extra poles. The four-pole connector is the most common at least from the availability of ready-made leads, as it allows for things like bi-amping (two of the four connections for the higher-frequency signal, with the other two for the lower-frequency signal) without two separate cables. Similarly, the eight-pole connector could be used for tri-amping (two poles each for low, mid and high frequencies with two unused), or quad-amping (two poles each for high, mid, low and sub).
Another use for the four-pole cable is to carry two channels of amplified signal from an amplifier to a pair of loudspeakers using a 'combiner' Y-lead connected to the two output channels, and a 'splitter' Y-lead to feed the loudspeakers. The 'combiner' and 'splitter' Y-leads are the same: two two-pole connectors on one end, connected to the ±1 and ±2 pins, respectively, of a four-pole line connector at the other end.[8] Some amplifiers and mixer-amplifiers are configured to do this without the need for a 'combiner'.
Also available are 2-pole "combo" receptacles that can also accept 4-pole cables and 1/4″ phone plugs.
In 2019 the manufacturer introduced the STX series which included male line connectors and female panel connectors.[6]
See also
[edit]References
[edit]- ^ "NL2FX drawing". Neutrik.
- ^ "Speakon trademark page". Neutrik.
- ^ E.g. Switchcraft HPC (High Power Connectors) Series
- ^ Neutrik. "NL4FC". Neutrik. Retrieved 2018-12-04.
- ^ "Speakon Speaker Connectors - The Basics". gollihurmusic.com.
- ^ a b "speakON® Connectors". neutrik.com.
- ^ "Electronics 2000 | Pin-outs | Speakon Connectors". www.electronics2000.co.uk.
- ^ "MX21's bi-amp information: custom speakon cable".