Jump to content

Belt-driven bicycle

From Wikipedia, the free encyclopedia

belt driven bike front belt drive system
Gates bike belt drive system
Belt-drive
Belt-drive single-speed rear hub on a Trek District
Belt-drive crankset on a Trek District
Belt-drive multi-speed rear hub gear on a Trek Soho

A belt-driven bicycle is a chainless bicycle that uses a flexible belt, typically a synchronous toothed design, in order to transmit power from the pedals to the wheel.

The application of belt drives to bicycles is growing, especially in the commuter bicycle market, due to the low maintenance and lubrication-free benefits. Belt drives are also available for stationary and fitness bicycles.[1]

Benefits

[edit]
  • Belts do not rust.
  • Lubrication is not required.
    • Cleanliness due to lack of lubrication.
    • Little to no maintenance.
  • Smoother operation.[2]
  • Quieter than chain.[3][4]
  • Longer life than metal bicycle chains.[5][6]
  • Some belt systems are lighter than conventional chain-driven system.[5][6]

Drawbacks

[edit]
  • Derailleurs cannot be used, so a hub gear is used if multiple gear ratios are required.
  • Most belts cannot be taken apart as a chain can, so a frame must be able to accommodate the belt by having an opening in the rear triangle or an elevated chain stay. There is only one option where the belt can be spliced and joined through the rear triangle.[7]
  • Belts come in limited selection of lengths, which must be accommodated in the design of the frame.
  • Belt-driven bicycles and their repair or replacement parts are scarcer at shops than bicycles with conventional chain.
  • Front and rear pulleys or sprockets must be well aligned to avoid excessive friction and wear. A chain is more flexible in this respect.[8]
  • Compared to a chain, belts are typically run at a much higher tension. This is done in order to avoid skipping of the belt while in use. However, high belt tensions can reduce the life expectancy of the bearings in the bottom bracket, as well as in the rear hub.[citation needed]
  • First-generation pulleys with dual guides had problems with snow becoming compacted and trapped in the pulley (up to complete inoperability in some cases). Second generation (one guide, wheel side) and third generation (center guide) improve upon the design.[citation needed]

Tensioning

[edit]

Tensioning can be implemented in all the same ways that single-speed chain drives can be tensioned. The fork ends for the rear axle are horizontal, in line with the belt, with or without chain tugs, which allows the distance between the rear wheel axle and the crank axle to be adjusted. The fork ends themselves can be moved, to change the distance between the rear wheel axle and the crank spindle. The fork ends are fixed but there is a separate tensioner pulley, which changes the travel distance of the belt.

History

[edit]

A belt drive for a bicycle was patented in the United States on April 8, 1890 by Charles D. Rice, Patent # 425,390.[9]

Mathew J. Steffens

In 1898, Mathew Joseph Steffens of Chicago, Illinois received a patent for a rear-wheel drive electric bicycle using a driving belt attached to the periphery of the pneumatic-tired wheel. By the early 1900s, some motorcycles were using leather drive belts.

Bridgestone Picnica

The Bridgestone Picnica belt-drive bicycle was introduced in the early 1980s. It used a tooth-belt drive like auto timing belts and Harley-Davidson drive belts, along with a novel two-part chainring that increased belt tension with increasing load. The Picnica was a folding bicycle, and part of the appeal of the belt drive was cleanliness. The Picnica was a small-wheel bicycle, so belt tension may have been less than on a bicycle with standard-size wheels. It was apparently successful, but was offered mainly in Japan.

Bridgestone offered belt-drive bicycles in the USA until they left the market about 1994. Since their innovation, they have continuously offered belt-drive bicycles in Japan including their best-selling Albelt model.

In 1984 and 1985, Mark Sanders, a designer who had earned his degree in mechanical engineering from Imperial College, London, designed a folding bicycle as part of his graduate studies in an Industrial Design Engineering (IDE) program. The program was run jointly by Imperial College and the Royal College of Art in London. He collaborated with a design engineer from Gates Corporation to outfit his bicycle with a belt, rather than a chain.

Strida 3 with kevlar belt drive

When his project was complete, Sanders chose entrepreneur and former Greg Norman manager James Marshall and a Glasgow manufacturer to turn his award-winning design into a product. The manufacturer coined the name Strida, and in 1987 the bicycle began rolling off the production line. In 2002 production was moved to Taiwanese manufacturer Ming Cycle in order to meet increased demand, and as of 2007, Ming Cycle fully owned the Strida brand and intellectual property rights.

iXi bicycles, distributed in the United States by Delta Cycle Corporation, followed in 2004 with a compact design that, like Strida, featured a belt drive. Other folding-bike manufacturers that have implemented a belt drive include U.S. company Bike Friday and Netherlands-based Bernds.

In 2007, Gates Corporation developed a high-modulus 8mm synchronous belt and sprocket system called the Carbon Drive System. The belt's pitch allowed for lower tension requirements to help prevent skipping. Lightweight, patent-pending sprockets have mud ports, openings under each tooth, which work to slough off debris.

In 2009, an increasing number of bicycle companies, including Trek and f8 Cycles, offered belt-driven bicycles. While builders initially focused on single-speeds and internal hubs, in early 2009 f8 used a Gates-compatible fixed-gear cog designed by Phil Wood & Co.,[10] offering a belt-driven fixed-gear bicycle.

In 2009, Wayne Lumpkin, owner of Spot Brand and best known as the founder of Avid, designed a belt system called CenterTrack. In 2010, Gates Corporation acquired a patent from Lumpkin for CenterTrack,[11] a new belt-and-pulley design that improves on the initial Carbon Drive System design. CenterTrack is more tolerant to misalignment than its predecessors. It is also lighter, 20% stronger due to a wider 11mm belt, yet has narrower pulleys, making packaging with the latest generation of internally geared hubs much easier.[3][12] The company’s CDX belt is the first belt drive designed for severe off-road use on mountain bikes.

In 2010, Daimler introduced the Smart eBike, a power-electric hybrid bicycle featuring Gates Carbon drive-belt system. The eBike is designed for a clean, grease-free ride.[13] Other notable eBike brands include Grace and Pi-Mobility.

In 2012, Continental AG’s subsidiary ContiTech introduced the CONTI® DRIVE SYSTEM for bicycles.[14] The CDS belt drive shared the basic operation of the early 8mm Gates Carbon Drive system, but employed aramid instead of carbon fibers in its construction. The Conti CDS was designed exclusively for ‘normal use on properly laid’ roads and paths.[15] ContiTech eventually switched to carbon belts for bicycle use, citing issues with traction using aramid fibers.[16]

The CDS belt drive was utilized on some Trek bicycles and the Sladda utility cycle marketed by IKEA of Sweden. After reports of failures of the belt itself and a recall, CDS was withdrawn from the belt-drive bicycle market.[17][18]

In 2018, Veer Cycles created the first belt drive conversion kit that allows riders to convert their chain driven bikes to belt drives. The belt is spliced to fit through the rear triangle and eliminates the need for a frame with a split already in it.[19][7] Veer has also shown a concept where the rear cog can change size (and thus gearing),[20] a concept that is reminiscent of derailleurs and implies that a hub gear with planetary gears may not be necessary in order to implement multi-speed gears on a belt-driven bike.

The possibilities for belt-driven bicycles are increasing as manufacturers of internal hub gears (gears inside the rear hub, which allow riders of belt-driven bicycles to shift easily) introduce new designs such as the Shimano Alfine 11 and Fallbrook Technologies's NuVinci. Other major internally geared hub makers include SRAM, Sturmey-Archer, Rohloff and Kindernay.

Another option to provide gears is to create a gearbox bicycle using a bracket-mounted gearbox like the Pinion P.18.[21]

Manufacturers

[edit]

The belts are typically made by the same manufacturing companies that produce toothed belts for automobiles, machinery, and other synchronous belt-drive applications.[citation needed]

Belt-drive manufacturers

[edit]

Current and former manufacturers of belt-drive bicycles and pedal belt-drive systems include:

OEM bicycle manufacturers

[edit]

Current and former bicycle manufacturers who have incorporated belt-drive on their bicycles include:

[edit]

See also

[edit]

References

[edit]
  1. ^ "Freemotion Fitness Carbon Drive". Archived from the original on 19 February 2013. Retrieved 2 May 2012.
  2. ^ Huang, James (2 January 2013). "Chain or belt drive: which is faster?". BikeRadar. Retrieved 26 August 2015.
  3. ^ a b "Building a Better Belt". Archived from the original on 9 April 2012. Retrieved 2 May 2012.
  4. ^ a b "Stuff We Like: Gates Carbon Drive Systems". Archived from the original on 6 December 2011. Retrieved 2 May 2012.
  5. ^ a b "Gates Carbon Drive Systems". Retrieved 5 August 2009.
  6. ^ a b "Cycle Drive Systems: FAQ". Archived from the original on 10 July 2009. Retrieved 5 August 2009.
  7. ^ a b "SOC18: Veer Belt Drive works on any bicycle frame...by cutting the belt". Bikerumor. 24 April 2018. Retrieved 27 June 2018.
  8. ^ Pardey, Hans-Heinrich (11 July 2011). "Spannend ist die richtige Spannung". Frankfurter Allgemeine Zeitung.
  9. ^ "Bicycle".
  10. ^ "f8 Cycles: Function". Archived from the original on 30 January 2010. Retrieved 9 February 2010.
  11. ^ Eisenberg, Anne (23 October 2010). "Bicycles, Unchained and Grease-Free". The New York Times.
  12. ^ "Gates Carbon Drive Products". Retrieved 2 May 2012.
  13. ^ "News from smart". Archived from the original on 1 May 2012. Retrieved 2 May 2012.
  14. ^ "From the magazine: Continental, Benchmark Drives develop belt drive". Retrieved 29 June 2023.
  15. ^ "Conti Drive System User Manual" (PDF). Retrieved 3 July 2023.
  16. ^ "Continental: Conti Drive System to use highly durable carbon belt". Retrieved 3 July 2023.
  17. ^ "Trek Safety Recall Notice" (PDF). Retrieved 29 June 2023.
  18. ^ "Consumer Products Safety Recall Notice No. 18-166". Retrieved 29 June 2023.
  19. ^ "Add a belt drive to any bike with Veer's belt drive". Retrieved 9 September 2023.
  20. ^ a b c Denham, Alee (28 June 2023). "3 Promising New Bicycle Belt Drivetrains From Eurobike 2023". Retrieved 9 September 2023.
  21. ^ "Pinion drive". Retrieved 6 March 2015.
  22. ^ System overview - advanced belt drive
  23. ^ optibelt TWIN TRACK
  24. ^ "Daimler Begins Deliveries of smart Electric Bikes". EV World. 2012. Archived from the original on 29 July 2012. Retrieved 10 May 2012. The drive is also of a very high quality with a completely maintenance- and oil-free carbon toothed belt instead of a conventional bicycle chain.
  25. ^ "On the road: Ikea Sladda bicycle review – 'Build your own Ikea bike? It's either a masterstroke or a recipe for disaster'". TheGuardian.com. 2 July 2016. Retrieved 2 July 2016.
[edit]
  • BikeCAD modeling a chain or belt drive.