Applications For Jigs and Fixtures

APPLICATIONS FOR JIGS AND FIXTURES
Typically, the jigs and fixtures found in a machine shop are for machining operations.
Other operations, however, such as assembly, inspection, testing, and layout, are also
areas where work holding devices are well suited. Figure 1-7 shows a list of the morecommon classifications and applications of jigs and fixtures used for manufacturing.
There are many distinct variations within each general classification, and many work
holders are actually combinations of two or more of the classifications shown.
EXTERNAL-MACHINING APPLICATIONS:
Flat-Surface Machining
Milling fixtures
Surface-grinding fixtures
Planing fixtures
Shaping fixtures
Cylindrical-Surface Machining
Lathe fixtures
Cylindrical-grinding fixtures
Irregular-Surface Machining
Band-sawing fixtures
External-broaching fixtures
INTERNAL-MACHINING APPLICATIONS:
Cylindrical- and Irregular-Hole Machining
Drill jigs
Boring jigs
Electrical-discharge-machining fixtures
Punching fixtures
Internal-broaching fixtures
NON-MACHINING APPLICATIONS:
Assembly
Welding fixtures
Mechanical-assembly fixtures
(Riveting, stapling, stitching, pinning, etc.)
Soldering fixtures
Inspection
Mechanical-inspection fixtures
Optical-inspection fixtures
Electronic-inspection fixtures
Finishing
Painting fixtures
Plating fixtures
Polishing fixtures
Lapping fixtures
Honing fixtures
Miscellaneous
Layout templates
Testing fixtures
Heat-treating fixtures
Modular Fixtures
Modular fixtures achieve many of the advantages of a permanent tool using only a
temporary setup. Depicted in Figure 1-4, these workholders combine ideas and
elements of permanent and general-purpose workholding.
Figure 1-4. Modular workholders combine ideas and elements of both permanent and
temporary workholding to make inexpensive-yet-durable workholders.
The primary advantage of modular fixtures is that a tool with the benefits of permanent
tooling (setup reduction, durability, productivity improvements, and reduced operator
decision-making) can be built from a set of standard components. The fixture can be
disassembled when the run is complete, to allow the reuse of the components in a
different fixture. At a later time the original can be readily reconstructed from drawings,
instructions, and photographic records. This reuse enables the construction of a
complex, high-precision tool without requiring the corresponding dedication of the fixture
components.
Elements of Jigs and Fixtures.

Various elements of jigs and fixtures and their details are follows.
1: Body
2: Locating devices
3: Clamping devices
4: Tool guide(jigs bushing)
1: Body:
The jig body is generally made of cost iron by casting process or
fabricated by welding together various slabs and bars of mild
steel. It may be heat treated to relief the stresses. Body is the
most prominent feature of the jig. Its main purpose is to support
and house the job.
The various jig body are follows:
(A):Plane Type Jig:

Plane type jig is the simplest type, it is used when plane holes are
to be drilled. It has either drill bushes for guiding the tools or the
holes without bushes.
(B): Channel Type Jig:

Channel type is made up from standard steel channel section.
(C): Box type Jig:

Box type jig is used where a component requires drilling in more
than one plane and the jig is to be provided with on equilant
number of drill bush plates. One side of the box is fitted with a lid
which can be opened for inserting the component and for
unloading it. It should be made as light as possible.
(D): The Built Up Jig:

The built up jig used dowels and screws for fabricating member
welded type. Standard steel sections are used in it for the limited
numbers of details, which are secured by means of screws and
dowels, the locating pins and the blocks are positioned so that the
greatest dimensional variation of the work piece may be
accommodated.
(E): Leaf Type Jig:
Leaf type jig is simple made from a block of steel fitted with two
adjustable locating screws and a spring loaded plunger. It is used
in case of measured large components where it may be both
unnecessary and construct a jig to hold the complete component ,
where madding is purely confined to a local section of the work
piece.
2:Locating Devices
The pins of various design and made of hardened steel are the
most common locating devices used to locate a work piece in a jig
or fixture. The shank of the pin is press fitted or driven into the
body of jig or fixture. The locating diameter of the pin is made
larger than the shank to prevent it from being forced into the jig
or fixture body due to the weight of the work piece or cutting
forces. Depending upon the mutual relation between the work
piece and the pin.
The pin may be classify as follows:
(A): Locating Pins:
When reamed or finally finished holes are available in work piece,

these can be used for locating purpose of the manner as shown ,
these are two types of locating pins:
Conical locating pins

Cylindrical locating pins
(B): Support Locating Pins:

With these pins (also known as rest pins) buttons or pads the
work piece with flat surfaces supported at convenient. In the fixed
support pins the locating face is either ground flat or curved.
Support pins with flat head are usually employed and provided
location and support to machine surface, because more contact
area is available during location. It would insure accurate and
stable location. The spherical head or round head rest buttons are
used for supporting rough surfaces (un machined and cast
surfaces) because they provide a point support which may be
stable under these circumstances. Adjustable type support pins
are used for work piece whose dimension can vary. For example
sand casting, forging or unmachined faces.
(C): Jack Pins:

Jack pins or spring pins are also used to locate the work piece
whose dimension are subjected to variation. The pin is allow to
come up under spring pressure or conversely is pressed down by
the work piece. When the location of the work piece is secured
the pin is locked in this position by means of locking screw.
Elements of jigs and fixtures:

3: Clamping devices:
If the work piece can not be restrained by the locating devices or
elements, it become necessary to clamp the work piece in jig or
fixture body. The most common example of clamping devices is
bench vice. The purpose of the clamping is to exert a pressure to
press a work piece against the locating surfaces and hold it there
in a position to the cutting forces. In bench vice the movable jaw
of the vice exert force on the work piece , their by holding it in

correct position of location in the fixed jaw of the vice.
The commonly used clamping devices are follows:
(A): Clamping Screws:
Clamping screws are used for light clamping. Clamping screws are
shown in fig.
(B): Hook Bolt Clamp:

This is very simple clamping device and is only suitable for light
work and where usual tip of the clamp is inconvenient. The typical
hook bolt clamp is shown.
(C): Bridge Clamp:

It is very simple and reliable clamping device. The clamping force
is applied by spring loaded nut.
(D): Heel Clamp:

These consists of a rusted plate, center stud and heel. This trap
should be strengthen at the point where the hole for the stud is
cut out, by increasing the thickness around the hole. The design
differ from simple bridge clamp in that a heel is provided at the
outer end of the clamp to guide its sliding motion for loading and
unloading the work piece.
(E): Swinging Strap(Latch Clamp):

This is a special type of clamp which provides a means of intry for
loading and unloading the work piece. For this the strap(latch or
lid) can be swing out from the work piece. The typical swing strap
or latch clamp is shown in figure.
(F): C-Clamp:
To unload the work piece, the locking nut is unscrewed by giving it
about one turn and this releases the c- clamp. When the clamp is
removed or swing away the work piece can freely pass over the
nut. To reverse procedure is adopted for loading the work piece.
>: Element of jigs and fixtures:
4: Tool Guide or Jig Bushing:

Sometimes the stiffness of the cutting tool may be in sufficient to
perform certain machining operations. Then to locate the tool
relative to the work, use is made of guiding parts such as jigs
bushing and templates. These must be precise, were resistance
and changeable.
Jig bushes are used in drilling and boring, a bush fits into the hole
of the jig, through which the drill passes. The diameter of the
bush depends on the diameter of the drill. Different type of
bushes are spot welded or screwed with the jig. Headless type
bushes are press fit into the hole of the job. Bushes are general
made of a good grade of tool steel to insure hardening at a fairly
no temperature and to lesson the danger of fire cracking.
Sometime the bushes for guiding tools may be of cast iron.
Hardened steel bushes are always preferable for guiding drills,
reamers and taps etc.
American standard bushes are classified in three categories.
1: press- fit wearing bushes
2: renewable wearing bushes
3: linear wearing bushes
Types of bushes (tool guide/jig bushes):

1: Press fit wearing bushes:
These bushes are used when little importance in put on accuracy
or finish and tool used is a twist drill. These bushing are installed
directly in the jig body and are used mainly for short protection.
There are two design of press fit bushing:
A> Plain or headless bush

B> Headed or flanged bush
2: Renewable bushes:
When the guide bushes requires periodic replacement (due to
wear of the inside diameter of the bush). Its replacement is simply
by using a renewable bush. These are of the flanged types and
sliding fit into the linear bush, which is installed press fitted into
the jig plate. The linear bush provides hardened wear resistance,
mating surface to the renewable bush. The renewable bushes

must be prevented from rotating or lifting with the drill. One
common method is to use a retaining screw.
3: Linear bushes:
These bushes are also known as master bushing, are permanently
fixed to the jig body. These acts as guides for renewable type
bushing. These bushes are be with or without head.

Applications For Jigs and Fixtures

Uploaded by

Copyright:

Available Formats

Applications For Jigs and Fixtures

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Applications For Jigs and Fixtures

Uploaded by

Copyright:

Available Formats

APPLICATIONS FOR JIGS AND FIXTURES

Elements of Jigs and Fixtures.

4: Tool guide(jigs bushing)

(A):Plane Type Jig:

(B): Channel Type Jig:

(C): Box type Jig:

(D): The Built Up Jig:

(E): Leaf Type Jig:

(A): Locating Pins:

When reamed or finally finished holes are available in work piece,

Conical locating pins

(B): Support Locating Pins:

(C): Jack Pins:

Elements of jigs and fixtures:

of the vice exert force on the work piece , their by holding it in

(B): Hook Bolt Clamp:

(C): Bridge Clamp:

(D): Heel Clamp:

(E): Swinging Strap(Latch Clamp):

>: Element of jigs and fixtures:

4: Tool Guide or Jig Bushing:

Types of bushes (tool guide/jig bushes):

A> Plain or headless bush

mating surface to the renewable bush. The renewable bushes

You might also like