Download
Share
Print this page
AMQ Amobi Desk Manual
  1. Manuals
  2. Brands
  3. AMQ Manuals
  4. Indoor Furnishing
  5. Amobi Desk One
  6. Manual

AMQ Amobi Desk Manual

Hide thumbs Also See for Amobi Desk:

Advertisement

Quick Links

Download this manual
Do NOT unpack with only one person.
Desk is heavy and can tip over causing serious injury.
Always use two or more people to unpack and set up desk.
Immediately rotate feet to 45 degrees or more.
2 person
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
Important: Changes or modifications to this product not authorized by AMQ could void your authority
to operate the product.
Amobi Desk
CAUTION
Warranty Replacement Instructions Guide
For commercial use only

Advertisement

loading

Related Manuals for AMQ Amobi Desk

Summary of Contents for AMQ Amobi Desk

  • Page 1 Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Important: Changes or modifications to this product not authorized by AMQ could void your authority to operate the product.

  • Page 2: Table Of Contents

    POWER CORD REPLACEMENT........53-64 amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 2...

  • Page 3: Important Safety Instructions

    RISK OF INJURY. Do not sit or stand on product. Use only as intended. Inspect regularly. STOP using if product is damaged or has loose parts. Only repair with AMQ authorized parts and methods. amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 3...
  • Page 4 Desk is heavy and can tip over causing serious injury. Always use two or more people to unpack and set up desk. Requires minimum of 2 person for removing Amobi Desk from its packaging & feet deployment. Immediately rotate feet to 45 degrees or more.
  • Page 5 A in Figure 1. Make sure that the product is connected to an outlet having the same configuration as the plug. GROUNDED OUTLET No adapter should be used with this product. GROUNDED OUTLET BOX Figure 1 Grounding methods amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 5...

  • Page 6: Worksurface Replacement

    WORKSURFACE REPLACEMENT COMPONENTS Worksurface amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 6...
  • Page 7 TOOL REQUIRED Electric Drill amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 7...
  • Page 8 Use an electric drill to remove 9 screws on the Worksurface. ST4.2 x 16 Step 2 Press and hold the Handle Button (1) and pulll down the Worksurface (2). Press the Handle Button amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 8...
  • Page 9 Step 3 Press down the Worksurface until a “click” can be felt when the Worksurface is rotated to a horizontal position. Press down the Worksurface Step 4 Pull out the Worksurface. amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 9...
  • Page 10 WORKSURFACE REPLACEMENT Step 5 Replace the damaged Worksurface. SWAP Step 6 Place the Worksurface on the cantilever plate, align the opening position and push it in to the end. amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 10...
  • Page 11 Worksurface & Main Body. Both side of the Worksurface & Main Body should have equal gaps and that the pre-pilot holes on the Worksurface are aligned with the holes on the Cantilever Plate. amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 11...
  • Page 12 WORKSURFACE REPLACEMENT Step 9 Use an electric drill to reinstall 9 screws(Torque : 1.4~1.8 N*m) to secure the Worksurface. ST4.2 x 16 amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 12...
  • Page 13 REAR PANEL SLOT REPLACEMENT COMPONENTS Rear Panel Slot amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 13...
  • Page 14 TOOL REQUIRED 4mm Hex Key amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 14...

  • Page 15: Rear Panel Slot Replacement

    Notice : To avoid damage, 2 person is required while installing/removing the Whiteboard or Felt Tackboard. LOCK UNLOCK Step 2 Then pull the Whiteboard/Felt Tackboard outwards then downwards to remove it. amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 15...
  • Page 16 REAR PANEL SLOT REPLACEMENT Step 3 hex key Hold the Rear Panel Slot with your hand, Use a 4mm to remove the two M6x14 screws. M6 x 14 Hold the Rear Panel Slot amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 16...
  • Page 17 Replace the damaged Rear Panel Slot. SWAP Step 5 hex key Hold the Rear Panel Slot with your hand, Use a 4mm to tightly the two M6x14 screws. M6 x 14 Hold the Rear Panel Slot amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 17...
  • Page 18 Notice : To avoid damage, 2 person is required while installing/removing the Whiteboard or Felt Tackboard. Step 7 Insert the Whiteboard/Felt Tackboard into the Rear Panel Slot at an angle with a straight trajectory. amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 18...
  • Page 19 Push-Lock Button on both sides to lock it in place. LOCK UNLOCK Push-Lock Button Whiteboard/Felt Tackboard can be locked or unlocked by pressing the Push-Lock Button. amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 19...

  • Page 20: Rear Handset Replacement

    REAR HANDSET REPLACEMENT COMPONENTS Rear Handset amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 20...
  • Page 21 TOOLS REQUIRED 3mm Hex Key 4mm Hex Key 5mm Hex Key amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 21...
  • Page 22 Notice : To avoid damage, 2 person is required while installing/removing the Whiteboard or Felt Tackboard. LOCK UNLOCK Step 2 Then pull the Whiteboard/Felt Tackboard outwards then downwards to remove it. amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 22...
  • Page 23 REAR HANDSET REPLACEMENT Step 3 Remove the 12 screws from the Rear Beam as shown in the figure below. M6 x 14 M5 x 14 M6 x 10 amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 23...
  • Page 24 REAR HANDSET REPLACEMENT Step 4 Remove the Rear Beam. Rear Beam Step 5 Unplug the Rear Handset Connector. Rear Handset Connector amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 24...
  • Page 25 REAR HANDSET REPLACEMENT Step 6 hex key Use a 4mm to remove the two M6x10 screws. Remove these two screws M6 x 10 Step 7 Replace the damaged Rear Handset. SWAP amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 25...
  • Page 26 Reinstall the new handset on the handset bracket and reconnect the wires. Step 9 hex key Use a 4mm to tightly the two M6x10 screws. Reinstall these two screws M6 x 10 amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 26...
  • Page 27 REAR HANDSET REPLACEMENT Step 10 Connect the power supply and check if the Amobi Desk can operate normally. When everything is ok, reinstall the Rear Beam. Rear Beam amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 27...
  • Page 28 Use a 4mm to tightly the four M6x14 screws and four M6x10 screws. hex key Use a 3mm to tightly the four M5x14 screws. M6 x 14 M5 x 14 M6 x 10 amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 28...
  • Page 29 Notice : To avoid damage, 2 person is required while installing/removing the Whiteboard or Felt Tackboard. Step 13 Insert the Whiteboard/Felt Tackboard into the Rear Panel Slot at an angle with a straight trajectory. amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 29...
  • Page 30 Push-Lock Button on both sides to lock it in place. LOCK UNLOCK Push-Lock Button Whiteboard/Felt Tackboard can be locked or unlocked by pressing the Push-Lock Button. amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 30...

  • Page 31: Front & Rear Castors Replacement

    FRONT & REAR CASTORS REPLACEMENT COMPONENTS Front Caster Rear Caster amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 31...
  • Page 32 TOOL REQUIRED 4mm Hex Key amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 32...
  • Page 33 Notice : To avoid damage, 2 person is required while installing/removing the Whiteboard or Felt Tackboard. LOCK UNLOCK Step 2 Then pull the Whiteboard/Felt Tackboard outwards then downwards to remove it. amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 33...
  • Page 34 FRONT & REAR CASTORS REPLACEMENT Step 3 Lower the Amobi Desk to its lowest position and unplug the power cable from the power supply. Step 4 Prepare a bench with soft cushion, as shown in the picture below. 20’’ 67’’...
  • Page 35 FRONT & REAR CASTORS REPLACEMENT Step 5 Lay the Amobi Desk with its Worksurface facing downwards on the cushion, exposing the rear section of the Amobi Desk upwards. 4 person Notice: It will take 4 person to tilt the Amobi Desk into a horizontal position like the diagram below.
  • Page 36 FRONT & REAR CASTORS REPLACEMENT Step 6 hex key Use a 4mm to remove the four M6x10 screws on the Rear Casters. M6 x 10 Step 7 Replace the damaged Rear Caster. SWAP amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 36...
  • Page 37 Use a 4mm to tightly the four M6x10 screws. M6 x 10 Step 9 hex key Use a 4mm to remove the four M6x10 screws on the Front Casters. M6 x 10 amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 37...
  • Page 38 FRONT & REAR CASTORS REPLACEMENT Step 10 Replace the damaged Front Caster. SWAP Step 11 hex key Use a 4mm to tightly the four M6x10 screws. M6 x 10 amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 38...
  • Page 39 4 person Notice: It will take 4 person to tilt the Amobi Desk into a horizontal position like the diagram below. Four people should carry the table by holding these four points. amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 39...
  • Page 40 Align the Whiteboard/Felt Tackboard into the Rear Panel Slot above at a slightly tilted angle. Rear Panel Slot 2 person Notice: To avoid damage, 2 person is required while installing/removing the Whiteboard or Felt Tackboard. amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 40...
  • Page 41 Push-Lock Button on both sides to lock it in place. LOCK UNLOCK Push-Lock Button Whiteboard/Felt Tackboard can be locked or unlocked by pressing the Push-Lock Button. amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 41...

  • Page 42: Foot Lock Switch Replacement

    FOOT LOCK SWITCH REPLACEMENT COMPONENTS Foot Lock Switch amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 42...
  • Page 43 TOOL REQUIRED 5mm Hex Key amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 43...
  • Page 44 2 person Notice: To avoid damage, 2 person is required while installing/removing the Whiteboard or Felt Tackboard. LOCK UNLOCK Step 2 Then pull the Whiteboard/Felt Tackboard outwards then downwards to remove it. amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 44...
  • Page 45 FOOT LOCK SWITCH REPLACEMENT Step 3 Lower the Amobi Desk to its lowest position and unplug the power cable from the power supply. Step 4 Prepare a bench with soft cushion, as shown in the picture below. 20’’ 67’’ Soft cushion 24’’...
  • Page 46 FOOT LOCK SWITCH REPLACEMENT Step 5 Lay the Amobi Desk with its Worksurface facing downwards on the cushion, exposing the rear section of the Amobi Desk upwards. 4 person Notice: It will take 4 person to tilt the Amobi Desk into a horizontal position like the diagram below.
  • Page 47 FOOT LOCK SWITCH REPLACEMENT Step 6 hex key Use a 5mm to remove the M8x12 screw on the Foot Lock Switch. M8 x 12 Step 7 Remove the damaged Foot Lock Switch. amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 47...
  • Page 48 FOOT LOCK SWITCH REPLACEMENT Step 8 Replace the damaged Foot Lock Switch. SWAP Step 9 Reinstall the Foot Lock Switch. amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 48...
  • Page 49 FOOT LOCK SWITCH REPLACEMENT Step 10 hex key Use a 5mm to tightly the M8x12 screw on the Foot Lock Switch. M8 x 12 amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 49...
  • Page 50 FOOT LOCK SWITCH REPLACEMENT Step 11 After making sure the Foot Lock Switch is properly installed and screws tighten, rotate the Amobi Desk back to its upright position. 4 person Notice: It will take 4 person to tilt the Amobi Desk into a horizontal position like the diagram below.
  • Page 51 Align the Whiteboard/Felt Tackboard into the Rear Panel Slot above at a slightly tilted angle. Rear Panel Slot 2 person Notice: To avoid damage, 2 person is required while installing/removing the Whiteboard or Felt Tackboard. amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 51...
  • Page 52 Push-Lock Button on both sides to lock it in place. LOCK UNLOCK Push-Lock Button Whiteboard/Felt Tackboard can be locked or unlocked by pressing the Push-Lock Button. amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 52...

  • Page 53: Power Cord Replacement

    POWER CORD REPLACEMENT COMPONENTS Power Cord amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 53...
  • Page 54 TOOLS REQUIRED 3mm Hex Key 4mm Hex Key 5mm Hex Key amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 54...
  • Page 55 Notice : To avoid damage, 2 person is required while installing/removing the Whiteboard or Felt Tackboard. LOCK UNLOCK Step 2 Then pull the Whiteboard/Felt Tackboard outwards then downwards to remove it. amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 55...
  • Page 56 POWER CORD REPLACEMENT Step 3 Remove the 12 screws from the Rear Beam as shown in the figure below. M6 x 14 M5 x 14 M6 x 10 amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 56...
  • Page 57 POWER CORD REPLACEMENT Step 4 Remove the Rear Beam. Rear Beam Step 5 hex key Use a 3mm to remove the two M4x16 screws. M4 x 16 amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 57...
  • Page 58 POWER CORD REPLACEMENT Step 6 Unplug the Power Cord connector. Unplug the connector Unscrew the plug Step 7 Remove the Protective Cover. Protective Cover amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 58...
  • Page 59 POWER CORD REPLACEMENT Step 8 Replace the damaged Power Cord. SWAP Step 9 Reinstall the Protective Cover. Protective Cover amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 59...
  • Page 60 POWER CORD REPLACEMENT Step 10 hex key Use a 3mm to tightly the two M4x16 screws. M4 x 16 Step 11 Reconnect the wires. amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 60...
  • Page 61 POWER CORD REPLACEMENT Step 12 Connect the power supply and check if the Amobi Desk can operate normally. When everything is ok, reinstall the Rear Beam. Rear Beam amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 61...
  • Page 62 Use a 4mm to tightly the four M6x14 screws and four M6x10 screws. hex key Use a 3mm to tightly the four M5x14 screws. M6 x 14 M5 x 14 M6 x 10 amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 62...
  • Page 63 Notice : To avoid damage, 2 person is required while installing/removing the Whiteboard or Felt Tackboard. Step 15 Insert the Whiteboard/Felt Tackboard into the Rear Panel Slot at an angle with a straight trajectory. amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 63...
  • Page 64 Push-Lock Button on both sides to lock it in place. LOCK UNLOCK Push-Lock Button Whiteboard/Felt Tackboard can be locked or unlocked by pressing the Push-Lock Button. amqsolutions.com AMOBI DESK Warranty Replacement Instructions Guide | 64...
  • Page 65 Please contact [email protected] if you are missing any parts, have difficulty with assembly, or have any product related questions.