What is damper and why used in transmission lines??? A damper in transmission lines is a device designed to absorb and dissipate mechanical vibrations or oscillations. It's used to reduce the amplitude of these vibrations caused by various factors like wind, ice, or the line's own weight. By doing so, dampers help prevent damage to the transmission line and its components, ensuring stability and reliability in the system.
Suruchi Tripathi’s Post
More Relevant Posts
-
The vibrating rod of the vibrating rod material level switch is excited by an electronic circuit and maintains resonance. When the measured medium reaches and partially covers the probe of the vibrating rod switch, the vibration damping of the vibrating rod switch suddenly increases. This change in vibration parameters will The relay is triggered by the detection loop, thereby providing upper and lower limit switch signals for material level control.whastapp+8613764891810
To view or add a comment, sign in
-
Insulated Male Disconnects https://lnkd.in/gG8G4q5v.. The optical isolation terminal has the advantages of low signal loss at the control end, high switching frequency, no mechanical contact jitter, no wear switching, high insulation voltage, no vibration, no positional influence, and long life. Therefore, male disconnect terminal is widely used in the field of automatic control.
To view or add a comment, sign in
-
Purchasing Manager|Beidou/GPS antennas, RF adapter connectors, plug connector, electrical data connectors|Kinghelm
What are the basic performance of connectors? Mechanical performance: insertion force, extraction force, mechanical life; Electrical performance: contact resistance, insulation resistance, electrical strength (resistance strength); Environmental performance: resistance to humidity, temperature, salt spray, vibration and impact.For RF coaxial connectors, there are also electrical indicators such as characteristic impedance, insertion loss, reflection coefficient, and voltage standing wave ratio (VSWR). https://lnkd.in/gMMrjMwQ
To view or add a comment, sign in
-
The optical isolation terminal has the advantages of low signal loss at the control end, high switching frequency, no mechanical contact jitter, no wear switching, high insulation voltage, no vibration, no positional influence, and long life. Therefore, male disconnect terminal is widely used in the field of automatic control.
To view or add a comment, sign in
-
Our core technology is sealless pumps (canned motor, magnetic driven and liquid ring vacuum types). For the safe transport of refrigerant, aggressive, toxic, hot, explosive, valuable and flammable liquids and liquefied gases :- Range of Applications: ❖ system pressures up to 1200 bar ❖ fluid temperatures from -160 C up to +480 C ❖ shaft powers from 1kW to 690 kW
To view or add a comment, sign in
-
Proper Tensioning Can Improve Belt Life. The number one cause of power transmission belt failure is improper tensioning. Belt Tension Meter The measured value is shown as frequency in Hz or strand force in N. Non-contact measuring occurs by sonic. https://lnkd.in/gb2JE_SG
To view or add a comment, sign in
-
The TPI Smart Vibration Analyzer 9085 Interprets, Analyzes and Trends Machine Conditions including bearing wear and temperature. Includes wireless charging! Additionally the 9085-Ex is an intrinsically safe version rated for use in Zone 0 environments. https://lnkd.in/dMeWUBj5
To view or add a comment, sign in
-
Question: Which of these tests would give you an idea of power transformer winding deformation in any way qualitatively or quantitatively: 1. Sweep Frequency Response Analysis 2. Impedance 3. Capacitance in C&DF 4. All of the above Share after answering but give explanation also for your answers. #Share
To view or add a comment, sign in
-
The working principle of small circuit breaker MCB and internal structure diagram are composed of insulating flame retardant shell, switch handle, electromagnetic coil, action contact, static contact, connecting plate, arc extinguishing hood, terminal column and other main parts.
To view or add a comment, sign in
-
A shock absorber is a device used to reduce or eliminate vibrations in a mechanical system. Its working principle is based on the use of elements such as springs, dampers and masses to absorb and dissipate vibration energy.
To view or add a comment, sign in