Dust can have detrimental effects on electrical and electronic systems. In this commentary paper, we examine the composition of common dust and debris, discuss how it can be introduced into sensitive equipment enclosures, and detail the cascade of potential failures that can unfold. https://bit.ly/45YsxMY
EFI Global’s Post
More Relevant Posts
-
Insulated Male Disconnects https://lnkd.in/gG8G4q5v.. The optical isolation terminal has the advantages of low signal loss at the control end, high switching frequency, no mechanical contact jitter, no wear switching, high insulation voltage, no vibration, no positional influence, and long life. Therefore, male disconnect terminal is widely used in the field of automatic control.
To view or add a comment, sign in
-
-
What is damper and why used in transmission lines??? A damper in transmission lines is a device designed to absorb and dissipate mechanical vibrations or oscillations. It's used to reduce the amplitude of these vibrations caused by various factors like wind, ice, or the line's own weight. By doing so, dampers help prevent damage to the transmission line and its components, ensuring stability and reliability in the system.
To view or add a comment, sign in
-
🚨New Blog Alert🚨 We discuss some of the electrical malfunctions that can happen inside of your furnace ➡️ https://bit.ly/3vAiy2t
Some Electrical Malfunctions in a Gas Furnace | Americool Heating & Air Conditioning
To view or add a comment, sign in
-
According to the principle of capacitive induction, when the height of the measured medium soaking the measuring electrode changes, its capacitance changes. It can convert the height changes of various material and liquid media into standard current signals and transmit them to the operation control room for centralized display, alarm or automatic control by secondary instruments or computer devices. Its good structure and installation method can be applied to high temperature, high pressure, strong corrosion, easy crystallization, anti-blocking, anti-freezing and solid powder and granular materials. whatspp+8613764891810
To view or add a comment, sign in
-
Refine your electronic circuit board repairs with our comprehensive guide! Discover the top 12 mistakes technicians make and learn how to avoid them. Whether you're a seasoned pro or just starting out, these tips will save you time, money, and headaches: https://lnkd.in/egTxhx8q
To view or add a comment, sign in
-
-
Repair Workshop Supervisor | Electrical Transformer Diagnostic Specialist | High-Voltage Testing Expert | commissioning of electrical equipment | field engineering
A DC high pot test, or a dielectric withstand test, is a way of assessing the cable insulation by applying a high voltage and observing the leakage current. The test can reveal flaws like nicks, cracks, or pinholes in the cable insulation, as well as insufficient creepage and clearance distances.
To view or add a comment, sign in
-
DIAGNOSING OPEN CIRCUITS. 🇦🇺 Of all the types of electrical problems, open circuit problems are the most common. Open circuits are typically caused by: 1. Disconnected connectors 2. Bad switches 3. Poor terminal contacts 4. Cut wires 5. Blown or defective fuses You can assume that you have an open circuit problem whenever there is no visible sign of operation. You can use a number of tools to find the location of an open circuit. Each of the tools has its advantages and disad vantages, so it's probably best to use a combination of them, depending on the situation.
To view or add a comment, sign in
-
-
Flying probe test may detect a cold joint that an in-circuit test (ICT) may not . The primary difference between the two tests is that ICT is a contact-based test, while flying probe testing is a non-contact test . In an ICT, a bed of nails fixture is used to make contact with the test points on the PCB, while in a flying probe test, small probes are used to make contact with the test points . The bed of nails fixture can sometimes cause damage to the PCB, which can lead to false positives or negatives. Cold joints may not always affect electrical continuity immediately but could cause intermittent issues over time. Cold joint can lead to reliability issues for electronic components, as it increases the electrical resistance of the joint, reducing its reliability.
To view or add a comment, sign in
-
-
Good Practice for Extending Thermocouples Watch the video to learn about the types of thermocouple grade cables, when to use them, what not to do as well as the consequences of using the wrong cables. https://lnkd.in/gRi6eYUs
Good Practice for Extending Thermocouples - Pyrosales
https://www.pyrosales.com.au
To view or add a comment, sign in
-
PM Quality Consulting Mexico Founder & Operations Manager Black Belt Six Sigma & Lean Manufacturing Consultant Quality Engineer in Electronic Manufacturing
What about if you repair your electronic process board instead of new one? here some outputs of what you can improve, we will be happy to support you!
Shut down due to electronic board damaged, please call us and we will make diagnosis and repair. Here some ideas of what you can improve 😀
To view or add a comment, sign in
-