Jump to content

Pennsylvania Railroad class FF1

From Wikipedia, the free encyclopedia
(Redirected from PRR FF1)
PRR FF1
Type and origin
Power typeElectric
BuilderAltoona Works
with Westinghouse
Build date1917
Total produced1
Specifications
Configuration:
 • Whyte2-6-6-2
 • AAR1-C+C-1
 • UIC1′C+C1'
Gauge4 ft 8+12 in (1,435 mm) standard gauge
Leading dia.36 in (914 mm)
Driver dia.72 in (1,829 mm)
Length76 ft 6 in (23.32 m)
Height14 ft 8 in (4.47 m)
Adhesive weight439,500 lb (199,400 kilograms; 199.4 metric tons)
Loco weight516,000 lb (234,100 kilograms; 234.1 metric tons)
Electric system/s11 kV  25 Hz AC Catenary
Current pickup(s)Pantograph
Traction motors4× Westinghouse model 451 1,910 hp (1,420 kW) three-phase motors
TransmissionRotary converter supplied 25 Hz three phase alternating current fed to motors able to run at one of two speeds and connected to the drivers through Jackshafts and side rods
Performance figures
Maximum speed20.6 mph (33.2 km/h)
Power output4,600 hp (3,400 kW)
Tractive effortContinuous: 87,200 lbf (388 kN)
Starting: 140,000 lbf (620 kN)
Career
ClassFF-1
Number in class1
Retired1940
DispositionScrapped
Detail of PRR FF1 truck

The Pennsylvania Railroad's class FF1 was an American electric locomotive, a prototype numbered #3931 and nicknamed "Big Liz". It was built in 1917 to haul freight trains across the Allegheny Mountains where the PRR planned to electrify. "Big Liz" proved workable but too powerful for the freight cars of the time with its 4,600 hp (3,400 kW) and 140,000 lbf (620 kN) of tractive effort. Pulling the train it regularly snapped couplers and when moved to the rear as a pusher its force was sufficient to pop cars in the middle of the train off the tracks.

It had a 2-6-6-2 wheel arrangement in two half-frames, connected in the center. Each frame had a pair of three-phase AC induction motors driving a jackshaft through gearing and a spring drive; side rods then drove the wheels. The jackshafts can be mistaken for an additional fourth axle but the "wheels" are cogwheels to transfer power from the motors to the jackshaft. Three-phase power for the 4 massive motors was supplied from the single phase overhead supply via a large rotary converter housed in the body of the locomotive. Combined rated output of the motors was 7,640 hp (5,700 kW), but the converter could only supply a short term 4,600 hp (3,400 kW) or a continuous 4,000 hp (3,000 kW). With three-phase induction motors there was no way to control the speed of the motors; changing the wiring of the motor poles allowed for two speed settings, 10.3 and 20.6 mph (16.6 and 33.2 km/h), which were considered enough to drag heavy freight trains up and down steep grades.

Its intended use as an Allegheny climber never realized and its power too much for the rolling stock in service at the time, Big Liz was sidelined until being cut up for scrap in 1940.

References

[edit]
  • Pennsylvania Railroad (July 1917). "Pennsylvania Electric Locomotive - Experimental Design for Heavy Trunk Line Service to Operate Over 24 Miles of One Per Cent Grade" (PDF). Railway Mechanical Engineer. 91 (7): 389–390.
  • Pennsylvania Railroad (February 1918). "Pennsylvania Electric Locomotive - A Description of Interesting Details in the Running Gear Construction and in the Electrical Equipment" (PDF). Railway Mechanical Engineer. 92 (2): 87–90.
  • Staufer, Alvin F.; Pennypacker, Bert (1962). Pennsy Power: Steam and Electric Locomotives of the Pennsylvania Railroad, 1900-1957. Research by Martin Flattley. Carollton, Ohio: Alvin F. Staufer. ISBN 978-0-9445-1304-0.