Cockcroft–Walton generator: Difference between revisions

Content deleted Content added

Inline

Revision as of 20:43, 17 March 2023

This Cockcroft–Walton particle accelerator was used during the development of the atomic bomb. Built in 1937 by Philips of Eindhoven it is now in the National Science Museum in London, England.

750 kV Cockcroft-Walton accelerator used as the initial particle injector of the Japanese KEK accelerator, Tsukuba, Japan. The CW generator is on the right, the particle source is on the left.

The Cockcroft–Walton (CW) generator, or multiplier, is an electric circuit that generates a high DC voltage from a low-voltage AC or pulsing DC input. It was named after the British and Irish physicists John Douglas Cockcroft and Ernest Thomas Sinton Walton, who in 1932 used this circuit design to power their particle accelerator, performing the first artificial nuclear disintegration in history.^[1] They used this voltage multiplier cascade for most of their research, which in 1951 won them the Nobel Prize in Physics for "Transmutation of atomic nuclei by artificially accelerated atomic particles".

The circuit was develoepd in 1919, by Heinrich Greinacher, a Swiss physicist. For this reason, this doubler cascade is sometimes also referred to as the Greinacher multiplier. Cockcroft–Walton circuits are still used in particle accelerators. They also are used in everyday electronic devices that require high voltages, such as X-ray machines, microwave ovens and photocopiers.

Operation

The CW generator is a voltage multiplier that converts AC or pulsing DC electrical power from a low voltage level to a higher DC voltage level. It is made up of a voltage multiplier ladder network of capacitors and diodes to generate high voltages. Unlike transformers, this method eliminates the requirement for the heavy core and the bulk of insulation/potting required. Using only capacitors and diodes, these voltage multipliers can step up relatively low voltages to extremely high values, while at the same time being far lighter and cheaper than transformers. The biggest advantage of such circuits is that the voltage across each stage of the cascade is equal to only twice the peak input voltage in a half-wave rectifier. In a full-wave rectifier it is three times the input voltage. It has the advantage of requiring relatively low-cost components and being easy to insulate. One can also tap the output from any stage, like in a multitapped transformer.

To understand the circuit operation, see the diagram of the two-stage version at right. Assume the circuit is powered by an alternating voltage V_i with a peak value of V_p, and initially the capacitors are uncharged. After the input voltage is turned on

When the input voltage V_i reaches its negative peak −V_p, current flows through diode D1 to charge capacitor C1 to a voltage of V_p.
When V_i reverses polarity and reaches its positive peak +V_p, it adds to the capacitor's voltage to produce a voltage of 2V_p on C1s righthand plate. Since D1 is reverse-biased, current flows from C1 through diode D2, charging capacitor C2 to a voltage of 2V_p.
When V_i reverses polarity again, current from C2 flows through diode D3, charging capacitor C3 also to a voltage of 2V_p.
When V_i reverses polarity again, current from C3 flows through diode D4, charging capacitor C4 also to a voltage of 2V_p.

With each change in input polarity, current flows up the "stack" of capacitors through the diodes, until they are all charged. All the capacitors are charged to a voltage of 2V_p, except for C1, which is charged to V_p. The key to the voltage multiplication is that while the capacitors are charged in parallel, they are connected to the load in series. Since C2 and C4 are in series between the output and ground, the total output voltage (under no-load conditions) is V_o = 4V_p.

This circuit can be extended to any number of stages. The no-load output voltage is twice the peak input voltage multiplied by the number of stages N or equivalently the peak-to-peak input voltage swing (V_pp) times the number of stages

V_{o}=2NV_{p}=NV_{\text{pp}},

The number of stages is equal to the number of capacitors in series between the output and ground.

One way to look at the circuit is that it functions as a charge "pump", pumping electric charge in one direction, up the stack of capacitors. The CW circuit, along with other similar capacitor circuits, is often called charge pump. For substantial loads, the charge on the capacitors is partially depleted, and the output voltage drops according to the output current divided by the capacitance.

Characteristics

In practice, the CW has a number of drawbacks. As the number of stages is increased, the voltages of the higher stages begin to "sag", primarily due to the electrical impedance of the capacitors in the lower stages. And, when supplying an output current, the voltage ripple rapidly increases as the number of stages is increased (this can be corrected with an output filter, but it requires a stack of capacitors in order to withstand the high voltages involved). For these reasons, CW multipliers with large number of stages are used only where relatively low output current is required. The sag can be reduced by increasing the capacitance in the lower stages, and the ripple can be reduced by increasing the frequency of the input and by using a square waveform. By driving the CW from a high-frequency source, such as an inverter, or a combination of an inverter and HV transformer, the overall physical size and weight of the CW power supply can be substantially reduced.

CW multipliers are typically used to develop higher voltages for relatively low-current applications, such as bias voltages ranging from tens or hundreds of volts to millions of volts for high-energy physics experiments or lightning safety testing. CW multipliers are also found, with a higher number of stages, in laser systems, high-voltage power supplies, X-ray systems, LCD backlighting, traveling-wave tube amplifiers, ion pumps, electrostatic systems, air ionisers, particle accelerators, copy machines, scientific instrumentation, oscilloscopes, television sets and cathode-ray tubes, electroshock weapons, bug zappers and many other applications that use high-voltage DC.

Image gallery

1.2 MV 6-stage Cockcroft–Walton accelerator at Clarendon Lab, Oxford University in 1948

3 MV CW accelerator at Kaiser Wilhelm Institute, Berlin in 1937, said to be the most powerful CW at the time (the two 4-stage ladders produced opposite polarity). Note the three human figures at top center for scale.

Control panel of the Kaiser Wilhelm machine

3-stage semiconductor diode cascade multiplier (green) in anode supply of a cathode-ray tube television set

Notes

^ Kleppner, Daniel; Kolenkow, Robert J. (1973). An Introduction to Mechanics (2nd ed.). Boston: McGraw-Hill. p. 498. ISBN 0-07-035048-5.

External links

Cockcroft–Walton Multipliers Tutorial – EEVBlog at YouTube
Cockcroft Walton
Cockcroft Walton used in particle accelerators
US Department of Energy

[1] Kleppner, Daniel; Kolenkow, Robert J. (1973). An Introduction to Mechanics (2nd ed.). Boston: McGraw-Hill. p. 498. ISBN 0-07-035048-5.

[1]

@@ Line 14: / Line 14: @@
 {{refimprove|date=March 2017}}
-The '''Cockcroft–Walton''' ('''CW''') '''generator''', or '''multiplier''', is an [[electric circuit]] that generates a high [[Direct current|DC]] [[voltage]] from a low-voltage [[Alternating current|AC]] or pulsing DC input.  It was named after the British and Irish physicists [[John Douglas Cockcroft]] and [[Ernest Walton|Ernest Thomas Sinton Walton]], who in 1932 used this circuit design to power their [[particle accelerator]], performing the first artificial nuclear disintegration in history.<ref>{{cite book |title=An Introduction to Mechanics |last1=Kleppner |first1=Daniel |last2=Kolenkow |first2=Robert J. |year=1973 |publisher=McGraw-Hill |location=Boston |isbn=0-07-035048-5 |page=[https://archive.org/details/introductiontome00dani/page/498 498] |edition=2nd |url-access=registration |url=https://archive.org/details/introductiontome00dani/page/498 }}</ref>  They used this [[voltage multiplier]] cascade for most of their research, which in 1951 won them the [[Nobel Prize in Physics]] for "[[nuclear transmutation|Transmutation of atomic nuclei]] by artificially accelerated atomic particles". The circuit was discovered in 1919, by [[Heinrich Greinacher]], a Swiss [[physicist]]. For this reason, this doubler cascade is sometimes also referred to as the '''Greinacher multiplier'''.  Cockcroft–Walton circuits are still used in particle accelerators. They also are used in everyday electronic devices that require high voltages, such as [[X-ray machine]]s, [[microwave oven]]s and [[photocopier]]s.
+The '''Cockcroft–Walton''' ('''CW''') '''generator''', or '''multiplier''', is an [[electric circuit]] that generates a high [[Direct current|DC]] [[voltage]] from a low-voltage [[Alternating current|AC]] or pulsing DC input.  It was named after the British and Irish physicists [[John Douglas Cockcroft]] and [[Ernest Walton|Ernest Thomas Sinton Walton]], who in 1932 used this circuit design to power their [[particle accelerator]], performing the first artificial nuclear disintegration in history.<ref>{{cite book |title=An Introduction to Mechanics |last1=Kleppner |first1=Daniel |last2=Kolenkow |first2=Robert J. |year=1973 |publisher=McGraw-Hill |location=Boston |isbn=0-07-035048-5 |page=[https://archive.org/details/introductiontome00dani/page/498 498] |edition=2nd |url-access=registration |url=https://archive.org/details/introductiontome00dani/page/498 }}</ref>  They used this [[voltage multiplier]] cascade for most of their research, which in 1951 won them the [[Nobel Prize in Physics]] for "[[nuclear transmutation|Transmutation of atomic nuclei]] by artificially accelerated atomic particles".
+The circuit was develoepd in 1919, by [[Heinrich Greinacher]], a Swiss [[physicist]]. For this reason, this doubler cascade is sometimes also referred to as the '''Greinacher multiplier'''.  Cockcroft–Walton circuits are still used in particle accelerators. They also are used in everyday electronic devices that require high voltages, such as [[X-ray machine]]s, [[microwave oven]]s and [[photocopier]]s.
 ==Operation==